The sky2 driver combines auto speed negotiation with automatic negotiation
of pause parameters; but the ethtool interface expects them to be
split. This patch allows autonegotiation to be used for speed, but
manually disable flow control.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Transmit completion can safely run lockless against transmit start.
In the normal case, completion is done from NAPI and only looks
at elements that are at the tail of the ring.  When doing shutdown
or reset, the transmiter should be completely block by NAPI disable
and blocking of transmit queue. 

Based on earlier work by Mike McCormack.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This unifies the places that bounce the device (suspend/resume
and restart). And makes the operations have the same semantics
as normal dev_open/dev_stop.

This also avoids setting the multicast addresses twice when
device is brought up.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The suspend and shutdown code plays with shared state. Use consistent
locking, for extra protection.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Avoid any possible problems with accessing PHY registers on shutdown.
This is a purely theoretical issue and is not related to any of the
outstanding bug reports. Since receiver and transmitter are already
shutdown and phy interrupts for this device are already disabled,
there should already be enough protection. Suggested by Mike McCormack.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reseting the tx chain too soon results in invalid tx queue positions
being delivered in the status queue.  This also makes sure there's no
overlap between the cleanup done by sky2_tx_clean() and
sky2_tx_done().
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is pure refactoring.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Keep sky2->tx_prod consistent since int might be examined by
an softirq poll or restart.
Signed-off-by: NMike McCormack <mikem@ring3k.org>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Also implement get/set BB mult, get/set TX gain, set RX gain,
disable/restore CRS, run/stop DDFS, RX IQ est and QDIV roundup
in the process.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Acked-by: NMichael Buesch <mb@bu3sch.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug in ath9k_stop() where the HW
was not put into FULL_SLEEP state. Not doing so will
cause issues in suspend-resume and the HW will not respond
to chip resets.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch fixes a bug where the device was enabled
before restoring the PCI state.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

diversity_control and antenna_switch_swap are already
present in ath9k_ops_config. Remove duplicate occurrences
in ath_hw.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

PHY counters are available in all chipsets supported
by ath9k. Remove the check.
Signed-off-by: NSujith <Sujith.Manoharan@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

ath9k supports the AR9002 family of chipsets. This includes
the AR9285 and the miniPCI AR9223 and AR9220 (which themselves
have AR9280+AR5133).

We now refer people to the wiki page as it seems this is not
as popular as we would have hoped.
Reported-by: NJD <jd1008@gmail.com>
Cc: Dakota Lee <Dakota.Lee@Atheros.com>
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Sometimes drivers might have a good reason to override
the PS default, like iwlwifi right now where it affects
RX performance significantly at this point. This will
allow them to override the default, if desired, in a
way that users can still change it according to their
trade-off choices, not the driver's, like would happen
if the driver just disabled PS completely then.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If you trigger a scan request on an interface and then
take it down, or rmmod the module or unplug the device
the driver might "forget" to cancel the scan request.
That is a bug in the driver, but the current behaviour
is that we just hang endlessly waiting for the netdev
refcount to become 0 which it never will. To improve
robustness, check for this situation in cfg80211, warn
about it and clean up behind the driver. I don't just
clean up silently because it's likely that the driver
also has some internal state it has now leaked.

Additionally, this fixes a locking bug, clearing the
scan_req pointer should be done under the rdev lock.

Finally, we also need to _wait_ for the scan work and
not just abort it since it might be pending and wanting
to do a cleanup.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The length of the fixed portion of plink confirm frames is 4 bytes longer than
the other plink_action frames.  This path corrects an error in the length
adjustment done for these type of frames.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

If a PREQ frame is received giving us a fresher DSN than what we have, record
the new dsn and mark it as valid.  This patch fixes a bug in the setting of the
MESH_PATH_DSN_VALID flag.

Also, minor fix to coding style on that file.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This matches ath9k, providing consistency when reading both drivers.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Now that its shared we can remove ath5k's own implementation.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Turns out ath5k and ath9k can share the same helper to
allocates RX skbs. We allocate skbs aligned to the cache line
size. This requirement seems to have come from AR5210; when
this was not done it seems sometimes we'd get bogus data. I'm
also told it may have been a performance enhancement
consideration. In the end I can't be sure we can remove this
on new hardware so just keep this and start sharing it through
ath.ko.

Make ath9k start using this, ath5k is next.
Signed-off-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Luis reported that IRQ_MASK conflicts with include/pcmcia/cs.h on
compat-wireless. Remove that and a bunch of other unused defines
from wl1251_reg.h.
Reported-by: NLuis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "wl1251: remove wl1251_ops" originally removed file wl1251_ops.c,
but while I rebased the patch the removal got lost. Now remote the file
for real.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Commit "iwlwifi: Traffic type and counter for debugFs" broke iwl3945 in
a case when CONFIG_IWLWIFI_LEDS is disabled:

drivers/net/wireless/iwlwifi/iwl-3945.c:580: error: 'hdr' undeclared (first use in this function)

Fix it by removing the ifdef check for hdr variable.
Signed-off-by: NKalle Valo <kalle.valo@iki.fi>
Acked-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make it possible to write individual gain table entries.
Allow gain table entries to be written outside gain table init.
Add version-agnostic helpers for writing gain tables.
Use the new TX gain table helpers during table init.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Add rx queue pausing to usbnet. This is needed by rndis_wlan so that it can
control rx queue and prevent received packets from being send forward before
rndis_wlan receives and handles 'media connect'-indication. Without this
establishing WPA connections is hard and fail often.

[v2] - removed unneeded use of skb_clone

Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NJussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Some of the new variables in b43_phy_lp appear to be dead code in
the vendor driver; they will be removed if they remain unused when
LP-PHY implementation is finished.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Devices created by the libertas driver are currently called eth%d. Which
is wrong, because the device does not at all have anything to do with
Ethernet. And it is also confusing when used on devices with more than
one network device.

Fix this by calling it wlan%d.
Signed-off-by: NDaniel Mack <daniel@caiaq.de>
Cc: Roel Kluin <roel.kluin@gmail.com>
Acked-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Mesh frames that could not be immediately resolved were queued with a NULL
info->control.vif.  This patch moves the call to mesh_nexthop_lookup closer to
the point where it is handed over to ieee80211_tx().  This ensures that the
unresolved frames are ready to be sent once the path is resolved.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Signed-off-by: NThadeu Lima de Souza Cascardo <cascardo@holoscopio.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There were a few warnings when compiling the wl1271 driver on 64 bit
architectures.  This was due to size mismatch of integers.

This commit fixes the following warnings:

drivers/net/wireless/wl12xx/wl1271_main.c: In function 'wl1271_irq_work':
drivers/net/wireless/wl12xx/wl1271_main.c:184: warning: large integer implicitly truncated to unsigned type
drivers/net/wireless/wl12xx/wl1271_boot.c: In function 'wl1271_boot_upload_firmware_chunk':
drivers/net/wireless/wl12xx/wl1271_boot.c:103: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
drivers/net/wireless/wl12xx/wl1271_boot.c:150: warning: format '%d' expects type 'int', but argument 2 has type 'size_t'
drivers/net/wireless/wl12xx/wl1271_boot.c: In function 'wl1271_boot_enable_interrupts':
drivers/net/wireless/wl12xx/wl1271_boot.c:278: warning: large integer implicitly truncated to unsigned type
Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NLuciano Coelho <luciano.coelho@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I completely missed the "one's complement" instruction from the specs.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Also add a "SPEX32" macro for extracting 32-bit SPROM variables.
Signed-off-by: NGábor Stefanik <netrolller.3d@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This prevents calling rcu_synchronize from within the tx path by moving the
table growth code to the mesh workqueue.

Move mesh_table_free and mesh_table_grow from mesh.c to mesh_pathtbl.c and
declare them static.

Also, re-enable mesh in Kconfig and update the configuration description.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Tested-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The mesh stack was enabling beaconing without specifying an interval.  This
patch defines a default beaconing interval of 1s.

Incidentally, this fixes mesh beaconing in mac80211_hwsim devices.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This change triggers a path discovery as soon as the link quality degrades
below a certain threshold.  This results in a faster path recovery time than
by simply relying on the periodic path refresh mechanism to detect broken
links.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The fail_avg value is used to compute the mesh metric, and was only being set
by the pid rate control module. This fixes the mesh path selection mechanism
for cards that use mistrel for rate control.
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The 11s task group recently changed the frame mesh multicast/broadcast frame
format to use 3-address.  This was done to avoid interactions with widely
deployed lazy-WDS access points.

This patch changes the format of group addressed frames, both mesh-originated
and proxied, to use the data format defined in draft D2.08 and forward.  The
address fields used for group addressed frames is:

In 802.11 header
 ToDS:0  FromDS:1
 addr1: DA  (broadcast/multicast address)
 addr2: TA
 addr3: Mesh SA

In address extension header:
 addr4: SA  (only present if frame was proxied)

Note that this change breaks backward compatibility with earlier mesh stack
versions.
Signed-off-by: NAndrey Yurovsky <andrey@cozybit.com>
Signed-off-by: NJavier Cardona <javier@cozybit.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>