Tegra only supports, and always enables, device tree. Remove all ifdefs
and runtime checks for DT support from the driver. Platform data is
therefore no longer required. Rework the driver to parse the device tree
directly into struct sdhci_tegra.
Signed-off-by: NStephen Warren <swarren@nvidia.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Many MMC capability flags are platform-dependent and are traditionally set
in platform data. With DT often each such capability requires a special
binding. Add bindings for MMC_CAP_SD_HIGHSPEED, MMC_CAP_MMC_HIGHSPEED,
MMC_CAP_POWER_OFF_CARD and MMC_CAP_SDIO_IRQ capabilities. Also add code to
DT parser to look up "keep-power-in-suspend" and "enable-sdio-wakeup"
bindings and set MMC_PM_KEEP_POWER and MMC_PM_WAKE_SDIO_IRQ respectively,
if found.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some SD/MMC interfaces use 2 power regulators: one to power the card itself
(Vcc) and another one to pull signal lines up (VccQ). In case of eMMC and
UHS SD cards the regulators also have to be configured to supply different
voltages. The preferred order of turning supply power on and off is to
turn Vcc first on and last off.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The tmio_mmc_cd_wakeup() inline function has been deprecated since 3.4 and
is unused since 3.4 too. Remove them.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use managed allocations to get memory, clock and interrupts . This
significantly simplifies clean up paths.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The struct sh_mobile_sdhi_info::pdata field was only used for platform-
based card detection and isn't used anymore since the migration to GPIO-
based MMC slot functions. Remove it.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add parsing of common and driver-specific DT bindings to the tmio-mmc
MMC host driver and the sh_mobile_sdhi interface layer.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Define device-tree bindings for the tmio-mmc driver to be able to specify
parameters, currently provided in platform data.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Use mmc_of_parse() to get interface capability flags and used GPIOs from
device-tree bindings.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

The "extern" keyword isn't required in function declarations, remove it.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

MMC defines a number of standard DT bindings. Having each driver parse
them individually adds code redundancy and is error prone. Provide a
standard function to unify the parsing. After all drivers are converted
to using it instead of their own parsers, this function can be integrated
into mmc_alloc_host().
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Clarify ways to specify write-protect and card-detect MMC lines in FDT.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

tmio-mmc platform flags can be set by various means, including caller
drivers and device-tree bindings, therefore it is better to only check
them in the tmio-mmc driver proper, not in caller drivers themselves.
Signed-off-by: NGuennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

3714f4315354 ("mmc: sdhci: update signal voltage switch code") changed the
type of the second parameter of sdhci_do_start_signal_voltage_switch(),
from "struct mmc_ios *ios" to "int signal_voltage" which causes the
following build warning:

drivers/mmc/host/sdhci.c:2044:2: warning: initialization from incompatible pointer type [enabled by default]
drivers/mmc/host/sdhci.c:2044:2: warning: (near initialization for 'sdhci_ops.start_signal_voltage_switch') [enabled by default]

Use the previous type so that it matches the start_signal_voltage_switch()
definition from host.h.
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Reviewed-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Some regulators don't report any voltage values, so checking supported
voltage range results in disabling all SDHCI_CAN_VDD_* flags and
registration failure. This patch finally provides a correct fix for the
registration of SDHCI driver with all possible voltage regulators:
dummy, fixed and regulated without using regulator_count_voltages()
hacks.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SDHCI_QUIRK_DATA_TIMEOUT_USES_SDCLK does basically the same as
implementing struct sdhci_ops .get_timeout_clock, so simply set that
quirk and remove the custom code to simplify the driver.
Reported-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NStephen Warren <swarren@wwwdotorg.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch supports packed write command of eMMC4.5 devices.  Several
writes can be grouped in packed command and all data of the individual
commands can be sent in a single transfer on the bus. Large amounts of
data in one transfer rather than several data of small size are
effective for eMMC write internally.  As a result, packed command help
write throughput be improved.  The following tables show the results
of packed write.

Type A:
test     none |  packed
iozone   25.8 |  31
tiotest  27.6 |  31.2
lmdd     31.2 |  35.4

Type B:
test     none |  packed
iozone   44.1 |  51.1
tiotest  47.9 |  52.5
lmdd     51.6 |  59.2

Type C:
test     none |  packed
iozone   19.5 |  32
tiotest  19.9 |  34.5
lmdd     22.8 |  40.7
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch adds packed command feature of eMMC4.5.  The maximum number
for packing read (or write) is offered and exception event relevant to
packed command which is used for error handling is enabled. If host
wants to use this feature, MMC_CAP2_PACKED_CMD should be set.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: NMaya Erez <merez@codeaurora.org>
Reviewed-by: NSubhash Jadavani <subhashj@codeaurora.org>
Reviewed-by: NNamjae Jeon <linkinjeon@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Several new models of readers use different way to select driving
capability (a necessary adjustment along with voltage change). Removing
this from device-independent rtsx_pci_sdmmc module. It will be implemented
in device-depend calls encapsulated by rtsx_pci_switch_output_voltage().
Signed-off-by: NRoger Tseng <rogerable@realtek.com>
Reviewed-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

mmc_regulator_set_ocr() depends on the ability of regulator to change the
voltage value. When regulator cannot change its voltage output, some code
is skipped to avoid reporting false errors on some boards, which use MMC
hosts with fixed regulators (e.g. Samsung Goni and UniversalC210 boards).

This patch replaces a hacky workaround based on regulator_count_voltages()
value with the correct call to recently introduced
regulator_can_change_voltage() function in regulators core.
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NKevin Liu <kliu5@marvell.com>
Signed-off-by: NJialing Fu <jlfu@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch fixes incorrect indentation.  (Just code cleanup)
Signed-off-by: NJaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

It's not necessary to start a new request while error handling if
the card was removed.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NKonstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This patch is derived from:
"mmc: fix async request mechanism for sequential read scenarios".

According as async transfer, a request is handled with twice mmc_start_req.
When the card is removed, the request is actually not issued in the first
mmc_start_req [__mmc_start_data_req]. And then mmc_wait_for_data_req_done
will come in the next mmc_start_req. But there is no event for completions.
wake_up_interruptible is needed in __mmc_start_data_req for the case of
removed card.
Signed-off-by: NSeungwon Jeon <tgih.jun@samsung.com>
Acked-by: NJaehoon Chung <jh80.chung@samsung.com>
Tested-by: NKonstantin Dorfman <kdorfman@codeaurora.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

4d55c5a1 ("mmc: sdhci: enable preset value after uhs initialization")
added preset value support and enabled it by default during sd card init.

Below are the enhancements introduced by this patch:

1. In current code, preset value is enabled after setting clock finished,
which means the clock is manually set by driver firstly and then suddenly
switched to preset value at this point. So the first setting is useless
and unnecessary. What's more, the first clock setting may differ from the
preset one.  The better way is enable preset value just after switch to
UHS mode so the preset value can take effect immediately. So move preset
value enable from mmc_sd_init_card to sdhci_set_ios which will be called
during set timing.

2. In current code, preset value is disabled at the beginning of
mmc_attach_sd.  It's too late since low freq (400khz) should be set in
mmc_power_up.  So move preset value disable to sdhci_set_ios which will
be called during power up.

3. host->clock and ios->drv_type should also be updated according to the
preset value if it's enabled. Current code missed this.

4. This patch also introduce a quirk to disable preset value in case
preset value doesn't work.

This patch has been verified on sdhci-pxav3 platform with both preset
enabled and disabled.
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Reviewed-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

When irq_of_parse_and_map() returns an error, it does as zero. But in
mmc_spi_get_pdata(), the error return case is compared against NO_IRQ.
This might work where NO_IRQ is zero (defaults to zero when undefined,
as on MIPS) but not where NO_IRQ is different, e.g. on ARM where it's -1.

This patch changes to comparison with 0 which is the error return value
of irq_of_parse_and_map().

Tested on ARM that mmc_spi is working now.
Signed-off-by: NRoland Stigge <stigge@antcom.de>
Signed-off-by: NChris Ball <cjb@laptop.org>

Update Maintainer email for omap_hsmmc, as Venkatraman will no longer
be able to maintain omap_hsmmc driver.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Acked-by: NVenkatraman S <svenkatr@gmail.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

Quite a few drivers have a implementation of the get_timeout_clock
callback which simply returns the result of clk_get_rate on the device's
clock. This patch adds a common implementation of this to the sdhci-pltfm
module and replaces all custom implementations with the common one.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Tested-by: NStephen Warren <swarren@wwwdotorg.org>
Acked-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NKevin Liu <kliu5@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The protocol related code is moved to core stack. So update the host
driver accordingly.
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Tested-by: NTim Wang <wangtt@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

When switching SD and SDIO cards from 3.3V to 1.8V signal levels, the
clock should be gated for 5 ms during the step. After enabling the
clock, the host should wait for at least 1 ms before checking for
failure. Failure by the card to switch is indicated by dat[0:3] being
pulled low. The host should check for this condition and power-cycle
the card if failure is indicated.

Add a retry mechanism for the SDIO case.

If the voltage switch fails repeatedly, give up and continue the
initialization using the original voltage.

This patch places a couple of requirements on the host driver:

 1) mmc_set_ios with ios.clock = 0 must gate the clock
 2) mmc_power_off must actually cut the power to the card
 3) The card_busy host_ops member must be implemented

if these requirements are not fulfilled, the 1.8V signal voltage switch
will still be attempted but may not be successful.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Signed-off-by: NKevin Liu <kliu5@marvell.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

Allow callers to access the start_signal_voltage_switch host_ops
member without going through any cmd11 logic. This is mostly a
preparation for the following signal voltage switch patch.

Also, reset ios.signal_voltage to its original value if
start_signal_voltage_switch fails.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

This host_ops member is used to test if the card is signaling busy by
pulling dat[0:3] low.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

Add mmc_power_cycle which can be used to power cycle for instance
SD-cards.
Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Tested-by: NWei WANG <wei_wang@realsil.com.cn>
Signed-off-by: NChris Ball <cjb@laptop.org>

Signed-off-by: NJohan Rudholm <johan.rudholm@stericsson.com>
Acked-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

SET_BLOCK_COUNT CMD23 is needed for all access to RPMB partition.  If
block count is not set by CMD23, all subsequent read/write commands fail
as per eMMC specification. So, If the host does not support CMD23, do not
expose RPMB partition.

Accessing RPMB partition can cause hang / huge delay for hosts which do
not support CMD23.
Signed-off-by: NBalaji T K <balajitk@ti.com>
Reported-and-Tested-by: NPeter Ujfalusi <peter.ujfalusi@ti.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

This driver handles the virtual MMC device present in the Goldfish emulator.
The patch folds together initial work from Mike Lockwood and patches by
San Mehat, Jun Nakajima and Tom Keel <thomas.keel@intel.com> plus cleanups
by Alan Cox to get it all into 3.6 shape.
Signed-off-by: NMike A. Chan <mikechan@google.com>
[cleaned up and x86 support added]
Signed-off-by: NSheng Yang <sheng@linux.intel.com>
Signed-off-by: NYunhong Jiang <yunhong.jiang@intel.com>
Signed-off-by: NXiaohui Xin <xiaohui.xin@intel.com>
Signed-off-by: NJun Nakajima <jun.nakajima@intel.com>
Signed-off-by: NBruce Beare <bruce.j.beare@intel.com>
[Moved to 3.4]
Signed-off-by: NTom Keel <thomas.keel@intel.com>
[Moved to 3.7]
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

None of mmc drivers implements bus-width as a required device tree
property.  Instead, some drivers like atmel-mci, dw_mmc, sdhci-s3c
implement it as an optional one, and will force bus width to be 1
when the property is absent.  Let's change the common binding to
reflect what the drivers are usually doing.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Signed-off-by: NChris Ball <cjb@laptop.org>

The i.MX esdhc has a nonstandard bit layout for the SDHCI_HOST_CONTROL
register. To support 8bit bus width on i.MX populate the platform_bus_width
callback. This is tested on an i.MX25, but should according to the datasheets
work on the other i.MX using this hardware aswell. The i.MX6, while having
a SDHCI_SPEC_300 controller, still uses the same nonstandard register layout.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

The 8bit in the function name is misleading. When set, it will be
used to set the bus width, regardless of whether 8bit or another
bus width is requested, so change the function name to
platform_bus_width.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>

SDHCI core will try to use Auto CMD23 for mmc card.  Currently, we will
see the following message with mmc card on usdhc due to the lacking of
Auto CMD23 support in the driver.

$ mmc0: new high speed MMC card at address 0001
mmcblk1: mmc0:0001 MMC02G 1.87 GiB
mmcblk1: error -84 transferring data, sector 0, nr 8, cmd response 0x900, card status 0xb00
mmcblk1: retrying using single block read
 mmcblk1:

Enable Auto CMD23 support for usdhc so that mmc card can work in
multiple block mode.
Signed-off-by: NShawn Guo <shawn.guo@linaro.org>
Tested-by: NDirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: NChris Ball <cjb@laptop.org>