Document debug level module options and
tda18271_config attach-time parameters.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Store IF Frequency in a u16 instead of a u32.  Multiply by 1000 before use.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Allow drivers to pass device-specific configuration parameters during attach.

If these parameters are omitted, default values will be used.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Move some common code to a new file to make this easier to look at.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Tested successfully with QAM256 digital cable.
Analog television is limping, needs more work.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

version 0.1
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

make set_analog_params function look consistent with set_params function
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Try to load non-MTS firmware instead.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Older em28xx devices does implement standard Audio Class.

However, on newer devices, this were replaced by a Vendor Class. This
patch autodetects that an em28xx lacks Audio Class and auto-loads
em28xx-alsa, for the devices that implements only a Vendor Class.

For devices with Audio Class, snd-usb-audio module will provide an ALSA
interface.

This patch uses the request_module_async function as defined on cx88-mpeg.c, 
originally wrote by Markus Rechberger.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Also fixes the remaining CodingStyle issues that Lindent didn't fix.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

em28xx-audio module exports em28xx Vendor Class audio as an -alsa
driver. This module were written based on usbaudio driver by Markus
Rechberger. Recently, he acked to allow us to merge it on kernel:

http://lists-archives.org/video4linux/20408-supporting-prolink-pixelview-405-dvd-maker.html

Thanks to Markus Rechberger <mrechberger@gmail.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Thanks to Markus Rechberger <mrechberger@gmail.com> for retriving those
commands.

Also, MTS firmware is required for audio to work on HVR950.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

It is possible to select audio inputs via em28xx or via ac97 functions.
This patch allows configuring a board to use either one way.

It also do some cleanups at audio setup configurations.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Due to tuner-xc2028.h, some extra directories should be added at .h search.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

This tool allows the extraction of xc3028 v2.7 firmware from HVR 12x0 file.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Basic cleanup.
Signed-off-by: NSteven Toth <stoth@hauppauge.com>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Break out the following new functions from tda18271_tune:

tda18271_calc_bp_filter
tda18271_calc_km
tda18271_calc_rf_band
tda18271_calc_gain_taper
tda18271_calc_ir_measure
tda18271_calc_rf_cal
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

We don't need to do a dbg_info during tda18271_attach anymore, since
the tda18271_get_id function will call dbg_info with the same information
and more.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Fix the following compiler error:

v4l2-i2c-drv.h:72: error: implicit declaration of function 'v4l2_i2c_attach'

Also, prevent multiple inclusions of v4l2-i2c-drv.h
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

tuner-core was checking if analog_ops->set_config is set.  If set, it would
complain that it isn't.  Fix this backwards logic to the proper behavior.
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Everybody forgets to add the Kconfig stuff after they add new card support :-/
Signed-off-by: NMichael Krufky <mkrufky@linuxtv.org>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NJean Delvare <khali@linux-fr.org>
Signed-off-by: NHans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

bttv driver is working as previously. An additional gain of about 1,5Kb were
obtained with the driver conversion to vidioc_ioctl2:

   text    data     bss     dec     hex filename
  89208   40244   57556  187008   2da80 old/bttv.ko
  88960   38740   57556  185256   2d3a8 new/bttv.ko

(measured on a x86_64)
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>

Since there are a few vidioc_ functions that were exported, rename those
functions to bttv_ in order to avoid poluting namespace.

The other functions were also renamed, to standardize inside the driver.
Signed-off-by: NMauro Carvalho Chehab <mchehab@infradead.org>