To get the chip into the expected state, even when the hardware reset pin
isn't connected, do a software reset in this case. It isn't as thorough as
the hardware reset, as the I2C communication block can not be reset for
obvious reasons, but it's getting the chip into a defined state.
Signed-off-by: NLucas Stach <l.stach@pengutronix.de>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190627085958.28331-1-l.stach@pengutronix.de

Transfer size of zero means a request to do an address-only
transfer. Since the HW support this, we probably shouldn't be just
ignoring such requests. While at it allow DP_AUX_I2C_MOT flag to pass
through, since it is supported by the HW as well.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-16-andrew.smirnov@gmail.com

We don't need 8 byte array, DP_LINK_STATUS_SIZE (6) should be
enough. This also gets rid of a magic number as a bonus.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-15-andrew.smirnov@gmail.com

tc_get_display_props() never reads more than a byte via AUX, so
there's no need to reserve 8 for that purpose. No function change
intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-14-andrew.smirnov@gmail.com

We never pass anything but 100 as timeout_ms to tc_aux_wait_busy(), so
we may as well hardcode that value and simplify function's signature.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-13-andrew.smirnov@gmail.com

tc_wait_pll_lock() is always called as a follow-up for updating
PLLUPDATE and PLLEN bit of a given PLL control register. To simplify
things, merge the two operation into a single helper function
tc_pllupdate() and convert the rest of the code to use it. No
functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-12-andrew.smirnov@gmail.com

Move common code converting clock rate to an appropriate constant and
configuring SYS_PLLPARAM register into a separate routine and convert
the rest of the code to use it. No functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-11-andrew.smirnov@gmail.com

Don't assume that requested data transfer size is the same as amount
of data that was transferred. Change the code to get that information
from DP0_AUXSTATUS instead.

Since the check for AUX_BUSY in tc_aux_get_status() is pointless (it
will always called after tc_aux_wait_busy()) and there's only one user
of it, inline its code into tc_aux_transfer() instead of trying to
accommodate the change above.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-10-andrew.smirnov@gmail.com

According to the datasheet tc358767 can transfer up to 16 bytes via
its AUX channel, so the artificial limit of 8 appears to be too
low. However only up to 15-bytes seem to be actually supported and
trying to use 16-byte transfers results in transfers failing
sporadically (with bogus status in case of I2C transfers), so limit it
to 15.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-9-andrew.smirnov@gmail.com

Simplify AUX data write by dropping index arithmetic and shifting and
replacing it with a call to a helper function that does two things:

    1. Copies user-provided data into a write buffer
    2. Transfers contents of the write buffer to up to 4 32-bit
       registers on the chip

Note that separate data endianness fix:

    tmp = (tmp << 8) | buf[i];

that was reserved for DP_AUX_I2C_WRITE looks really strange, since it
will place data differently depending on the passed user-data
size. E.g. for a write of 1 byte, data transferred to the chip would
look like:

[byte0] [dummy1] [dummy2] [dummy3]

whereas for a write of 4 bytes we'd get:

[byte3] [byte2] [byte1] [byte0]

Since there's no indication in the datasheet that I2C write buffer
should be treated differently than AUX write buffer and no comment in
the original code explaining why it was done this way, that special
I2C write buffer transformation was dropped in this patch.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-8-andrew.smirnov@gmail.com

Simplify AUX data read by removing index arithmetic and shifting with
a helper function that does two things:

    1. Fetch data from up to 4 32-bit registers from the chip
    2. Copy read data into user provided array.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-7-andrew.smirnov@gmail.com

A very unfortunate aspect of tc_write()/tc_read() macro helpers is
that they capture quite a bit of context around them and thus require
the caller to have magic variables 'ret' and 'tc' as well as label
'err'. That makes a number of code paths rather counter-intuitive and
somewhat clunky, for example tc_stream_clock_calc() ends up being like
this:

	int ret;

	tc_write(DP0_VIDMNGEN1, 32768);

	return 0;
err:
	return ret;

which is rather surprising when you read the code for the first
time. Since those helpers arguably aren't really saving that much code
and there's no way of fixing them without making them too verbose to
be worth it change the driver code to not use them at all.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-6-andrew.smirnov@gmail.com

Simplify tc_set_video_mode() by replacing explicit shifting using
macros from <linux/bitfield.h>. No functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-5-andrew.smirnov@gmail.com

Replace explicit polling in tc_link_training() with equivalent call to
tc_poll_timeout() for simplicity. No functional change intended (not
including slightly altered debug output).
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-4-andrew.smirnov@gmail.com

Replace explicit polling loop with equivalent call to
tc_poll_timeout() for brevity. No functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-3-andrew.smirnov@gmail.com

Implementation of tc_poll_timeout() is almost a 100% copy-and-paste of
the code for regmap_read_poll_timeout(). Replace copied code with a
call to the original. While at it change tc_poll_timeout to accept
"struct tc_data *" instead of "struct regmap *" for brevity. No
functional change intended.
Signed-off-by: NAndrey Smirnov <andrew.smirnov@gmail.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Cc: Laurent Pinchart <Laurent.pinchart@ideasonboard.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: Andrey Gusakov <andrey.gusakov@cogentembedded.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Cory Tusar <cory.tusar@zii.aero>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: dri-devel@lists.freedesktop.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190619052716.16831-2-andrew.smirnov@gmail.com

Add support for interrupt and hotplug handling. Both are optional.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-24-tomi.valkeinen@ti.com

Add GPIO and interrupt related registers for HPD work. Mark INTSTS_G and
GPIOI as volatile.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-23-tomi.valkeinen@ti.com

We need to know the link bandwidth to filter out modes we cannot
support, so we need to have read the display props before doing the
filtering.

To ensure we have up to date display props, call tc_get_display_props()
in the beginning of tc_connector_get_modes().
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-22-tomi.valkeinen@ti.com

In tc_bridge_mode_set callback, we store the pointer to the given
drm_display_mode, and use the mode later. Storing a pointer in such a
way looks very suspicious to me, and I have observed odd issues where
the timings were apparently (at least mostly) zero.

Do a copy of the drm_display_mode instead to ensure we don't refer to
freed/modified data.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-21-tomi.valkeinen@ti.com

drm_connector_helper_funcs.best_encoder is only needed when the
connector can have more than one encoder, and that is never the case
here.

So remove tc_connector_best_encoder.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-20-tomi.valkeinen@ti.com

We have tc_connector_mode_valid() to filter out videomdoes that the
tc358767 cannot support. As it is a bridge limitation, change the code
to use drm_bridge_funcs's mode_valid instead.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-19-tomi.valkeinen@ti.com

tc_main_link_enable() checks if videomode has been set, and fails if
there's no videomode. As tc_main_link_enable() no longer depends on the
videomode, we can drop the check.

Also, while tc_stream_enable() does depend on the videomode, we can
expect that a mode has been set before drm_bridge_funcs.enable is
called, so we don't need the check there either.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-18-tomi.valkeinen@ti.com

The current link training code does unnecessary retry-loops, and does
extra writes to the registers. It is easier to follow the flow and
ensure it's similar to Toshiba's documentation if we deal with LT inside
tc_main_link_enable() function.

This patch adds tc_wait_link_training() which handles waiting for the LT
phase to finish, and does the necessary LT register setups in
tc_main_link_enable, without extra loops.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-17-tomi.valkeinen@ti.com

The driver has a loop after ending link training, where it reads the
DPCD link status and prints an error if that status is not ok.

The loop is unnecessary, as far as I can understand from DP specs, so
let's remove it. We can also print the more specific errors to help
debugging.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-16-tomi.valkeinen@ti.com

At the end of the link training, two steps have to be taken: 1)
tc358767's LT mode is disabled by a write to DP0_SRCCTRL, and 2) Remove
LT flag in DPCD 0x102.

Toshiba's documentation tells to first write the DPCD, then modify
DP0_SRCCTRL. In my testing this often causes issues, and the link
disconnects right after those steps.

If I reverse the steps, it works every time. There's a chance that this
is DP sink specific, though, but as my testing shows this sequence to be
much more reliable, let's change it.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-15-tomi.valkeinen@ti.com

For some reason the driver has a msleep(100) after writing to
DP_PHY_CTRL. Toshiba's documentation doesn't suggest any delay is
needed, and I have not seen any issues with the sleep removed.

Drop it, as msleep(100) is a rather big one.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NAndrey Gusakov <andrey.gusakov@cogentembedded.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-14-tomi.valkeinen@ti.com

Link training will sometimes fail if the DP link is enabled when
tc_main_link_enable() is called. The driver makes sure the DP link is
disabled when the DP output is disabled, and we never enable the DP
without first disabling it, so this should never happen.

However, as the HW behavior seems to be somewhat random if DP link has
erroneously been left enabled, let's add a WARN_ON() for the case and
set DP0CTL to 0.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-13-tomi.valkeinen@ti.com

Currently the code writes 0 to DP0CTL in tc_stream_disable(), which
disables the whole DP link instead of just the video stream. We always
disable the link and the stream together from tc_bridge_disable(), so
this doesn't cause any issues.

Nevertheless, fix this by only clearing VID_EN in tc_stream_disable to
stop the video stream while keeping the link enabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-12-tomi.valkeinen@ti.com

Currently we have tc_main_link_setup(), which configures and enabled the
link, but we have no counter-part for disabling the link.

Add tc_main_link_disable, and rename tc_main_link_setup to
tc_main_link_enable.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-11-tomi.valkeinen@ti.com

We set up the PXL PLL inside tc_main_link_setup. This is unnecessary,
and makes tc_main_link_setup depend on the video-mode, which should not
be the case. As PXL PLL is used only for the video stream (and only when
using the HW test pattern), let's move the PXL PLL setup into
tc_stream_enable.

Also, currently the PXL PLL is only disabled if the driver if removed.
Let's disable the PXL PLL when the stream is disabled.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-10-tomi.valkeinen@ti.com

It is nicer to have enable/disable functions instead of set(bool enable)
style function.

Split tc_main_link_stream into tc_stream_enable and tc_stream_disable.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-9-tomi.valkeinen@ti.com

The driver currently sets the video stream registers in
tc_main_link_setup. One should be able to establish the DP link without
any video stream, so a more logical place is to configure the stream in
the tc_main_link_stream. So move them there.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-8-tomi.valkeinen@ti.com

The driver sets up AUX link at probe time, but, for some reason, also
sets the main link's number of lanes using tc->link.base.num_lanes. This
is not needed nor correct, as the number of lanes has not been decided
yet. The number of lanes will be set later during main link setup.

Modify aux_link_setup so that it does not use tc->link, and thus makes
aux setup independent of the link probing.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-7-tomi.valkeinen@ti.com

swing and preemp fields are not used. Remove them.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-6-tomi.valkeinen@ti.com

Minor cleanups:
- Use bool for boolean fields
- Use DP_MAX_DOWNSPREAD_0_5 instead of BIT(0)
- debug print down-spread and scrambler status
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Reviewed-by: NLaurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-5-tomi.valkeinen@ti.com

DP always uses ANSI 8B10B encoding. Some monitors (old?) may not have
the ANSI 8B10B bit set in DPCD, even if it should always be set.

The tc358767 driver currently respects that flag, and turns the encoding
off if the monitor does not have the bit set, which then results in the
monitor not working.

This patch makes the driver to always use ANSI 8B10B encoding, and drops
the 'coding8b10b' field which is no longer used.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-4-tomi.valkeinen@ti.com

We need to reset DPCD voltage-swing & pre-emphasis before starting the
link training, as otherwise tc358767 will use the previous values as
minimums.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-3-tomi.valkeinen@ti.com

tc_aux_get_status() does not report AUX_TIMEOUT correctly, as it only
checks the AUX_TIMEOUT if aux is still busy. Fix this by always checking
for AUX_TIMEOUT.
Signed-off-by: NTomi Valkeinen <tomi.valkeinen@ti.com>
Reviewed-by: NAndrzej Hajda <a.hajda@samsung.com>
Signed-off-by: NAndrzej Hajda <a.hajda@samsung.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190528082747.3631-2-tomi.valkeinen@ti.com

Based on 3 normalized pattern(s):

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version this program is distributed in the
  hope that it will be useful but without any warranty without even
  the implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version [author] [kishon] [vijay] [abraham]
  [i] [kishon]@[ti] [com] this program is distributed in the hope that
  it will be useful but without any warranty without even the implied
  warranty of merchantability or fitness for a particular purpose see
  the gnu general public license for more details

  this program is free software you can redistribute it and or modify
  it under the terms of the gnu general public license as published by
  the free software foundation either version 2 of the license or at
  your option any later version [author] [graeme] [gregory]
  [gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
  [kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
  [hk] [hemahk]@[ti] [com] this program is distributed in the hope
  that it will be useful but without any warranty without even the
  implied warranty of merchantability or fitness for a particular
  purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

  GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1105 file(s).
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NAllison Randal <allison@lohutok.net>
Reviewed-by: NRichard Fontana <rfontana@redhat.com>
Reviewed-by: NKate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.deSigned-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>