When the firmware doesn't support LLDP or DCBX, the driver should switch
to "software LLDP mode". This patch adds support for the same.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds a new function ice_pf_dcb_cfg (and related helpers)
which applies the DCB configuration obtained from the firmware. As
part of this, VSIs/netdevs are updated with traffic class information.

This patch requires a bit of a refactor of existing code.

1. For a MIB change event, the associated VSI is closed and brought up
   again. The gap between closing and opening the VSI can cause a race
   condition. Fix this by grabbing the rtnl_lock prior to closing the
   VSI and then only free it after re-opening the VSI during a MIB
   change event.

2. ice_sched_query_elem is used in ice_sched.c and with this patch, in
   ice_dcb.c as well. However, ice_dcb.c is not built when CONFIG_DCB is
   unset. This results in namespace warnings (ice_sched.o: Externally
   defined symbols with no external references) when CONFIG_DCB is unset.
   To avoid this move ice_sched_query_elem from ice_sched.c to
   ice_common.c.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a new top level function ice_init_dcb (and
related lower level helper functions) which continues the DCB init
flow.

This function uses ice_get_dcb_cfg to get, parse and store the DCB
configuration. Once this is done, it sets itself up to be notified
by the firmware on LLDP MIB change events.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch introduces a skeleton for ice_init_pf_dcb, the top level
function for DCB initialization. Subsequent patches will add to this
DCB init flow.

In this patch, ice_init_pf_dcb checks if DCB is a supported capability.
If so, an admin queue call to start the LLDP and DCBx in firmware is
issued. If not, an error is reported. Note that we don't fail the driver
init if DCB init fails.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump driver version to 0.7.3
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Capitalize abbreviations and spell out some that aren't obvious.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes typos in code comments.
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are two reasons for this.

First, the xmit_more flag conceptually doesn't fit into the skb, as
xmit_more is not a property related to the skb.
Its only a hint to the driver that the stack is about to transmit another
packet immediately.

Second, it was only done this way to not have to pass another argument
to ndo_start_xmit().

We can place xmit_more in the softnet data, next to the device recursion.
The recursion counter is already written to on each transmit. The "more"
indicator is placed right next to it.

Drivers can use the netdev_xmit_more() helper instead of skb->xmit_more
to check the "more packets coming" hint.

skb->xmit_more is retained (but always 0) to not cause build breakage.

This change takes care of the simple s/skb->xmit_more/netdev_xmit_more()/
conversions.  Remaining drivers are converted in the next patches.
Suggested-by: NEric Dumazet <edumazet@google.com>
Signed-off-by: NFlorian Westphal <fw@strlen.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Some enums in ice_tx_desc_cmd_bits have a trailing /* 2 BITS */ comment,
but the value has just one bit set (ex. ICE_TX_DESC_CMD_L4T_EOFT_SCTP
has the value 0x200 (i.e. only bit 9 is set). This is confusing and
misleading. So remove the comment.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since the driver now hard codes the ITR granularity to 2 us in the
GLINT_CTL register the comment next to ITR_GRAN_S needs to be updated.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove some redundant text in the function header for __ice_vsi_get_qs
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Single statement if conditions don't need braces. Remove it.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 37bb8390 ("ice: Move common functions out of ice_main.c part
7/7") seems to have inadvertently introduced a function prototype for
ice_vsi_cfg_tc without a corresponding function implementation. Remove it.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we aren't checking for the ICE_FC_NONE case for the current
flow control mode. This is causing "Unknown" to be printed for the
current flow control method if flow control is disabled. Fix this by
adding the case for ICE_FC_NONE to print "None".
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently the ice_q_vector structure and ice_ring_container structure
are taking up more space than necessary due to cache alignment holes
and unnecessary variables respectively. This is not helping the
driver's performance. The following fixes were done to improve cache
alignment, reduce wasted space, and increase performance.

1. Remove the ice_latency_range enum as it is unused.
2. Remove the latency_range variable in the ice_ring_container structure.
3. Change the size of the itr_idx in the ice_ring_container structure
   from an int to an u16. This reduced the size of ice_ring_container
   structure to 32 Bytes so it has no holes or padding.
4. Re-arrange the ice_q_vector structure using pahole to align
   members as best as possible in regards to 64 Byte cache line size.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

If filter already exists, do not go through error path flow but instead
continue to process rest of the function. Hence have an appropriate check
after adding MAC filters.
Signed-off-by: NPreethi Banala <preethi.banala@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes issue that occurs when VF is attempting to remove
default LAN/MAC address, which is programmed by the administrator.
We shouldn't return error for the call by the VF, but continue with
the remaining steps to handle MAC opcode. Also update the dev_err
message to explicitly say that VF can't change MAC programmed by PF.

Also change "mac" to "MAC" for kernel print statements in the same file.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VPINT_MBX_CTL register array must be programmed to enable VF admin
queue interrupts. Without this, VFs never get interrupts on vector 0,
and some VF drivers will fail to init.
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

commit 63f545ed ("ice: Add support for adaptive interrupt moderation")
was meant to add support for adaptive interrupt moderation but there was
an error on my part while formatting the patch, and thus only part of the
patch ended up being submitted.

This patch rectifies the error by adding the rest of the code.

Fixes: 63f545ed ("ice: Add support for adaptive interrupt moderation")
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch implements the following pci_error_handler ops:
	.error_detected = ice_pci_err_detected
	.slot_reset = ice_pci_err_slot_reset
	.reset_notify = ice_pci_err_reset_notify
	.reset_prepare = ice_pci_err_reset_prepare
	.reset_done = ice_pci_err_reset_done
	.resume = ice_pci_err_resume
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Currently we check if the __ICE_PREPARED_FOR_RESET bit is set prior to
calling ice_prepare_for_reset in ice_reset_subtask(), but we aren't
checking that bit in ice_do_reset() before calling
ice_prepare_for_reset(). This is not consistent and can cause issues if
ice_prepare_for_reset() is called prior to ice_do_reset(). Fix this by
checking if the __ICE_PREPARED_FOR_RESET bit is set internal to
ice_prepare_for_reset().
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When communicating with the AVF driver, we need to use the status codes
from virtchnl.h, not our own ice-specific codes. Without this, when an
error occurs, the VF will report nonsensical results.

NOTE: this depends on changes made to include/linux/avf/virtchnl.h by
commit bb58fd7e ("i40e: Update status codes")
Signed-off-by: NMitch Williams <mitch.a.williams@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Two log messages contained newlines in the middle of the message. This
resulted in unexpected driver log output.

This patch removes the newlines to restore consistency with the rest of
the driver log messages.
Signed-off-by: NJeremiah Kyle <jeremiah.kyle@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This structure is used to define the packet flags. These flags are
applicable for both TX and RX packet. Thus, this patch changes its
name from ice_rx_flag64_bits to ice_flg64_bits, and its member definition.
Signed-off-by: NChinh T Cao <chinh.t.cao@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

There are numerous for() loops iterating over each of the max traffic
classes.  Use a simple iterator macro instead to make the code cleaner.
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Update VF VSI tc info along with vsi->num_txq/num_rxq when VF requests to
configure queues.
Signed-off-by: NPreethi Banala <preethi.banala@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In the current implementation of ice_reset_subtask, if multiple reset
types are set in the pf->state, the most intrusive one is meant to be
performed only, but the bits requesting the other types are not being
cleared. This would lead to another reset being performed the next time
the service task is scheduled.

Change the flow of ice_reset_subtask so that all reset request bits in
pf->state are cleared, and we still perform the most intrusive of the
resets requested.
Signed-off-by: NDave Ertman <david.m.ertman@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Provide DMA_ATTR_WEAK_ORDERING and DMA_ATTR_SKIP_CPU_SYNC attributes to
the DMA API during the mapping operations on Rx side. With this change
the non-x86 platforms will be able to sync only with what is being used
(2k buffer) instead of entire page. This should yield a slight
performance improvement.

Furthermore, DMA unmap may destroy the changes that were made to the
buffer by CPU when platform is not a x86 one. DMA_ATTR_SKIP_CPU_SYNC
attribute usage fixes this issue.

Also add a sync_single_for_device call during the Rx buffer assignment,
to make sure that the cache lines are cleared before device attempting
to write to the buffer.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Refactor ice_fetch_rx_buf and ice_add_rx_frag in a way that we have
standalone functions that do either the skb construction or frag
addition to previously constructed skb.

The skb handling between rx_bufs is spread among various functions. The
ice_get_rx_buf will retrieve the skb pointer from rx_buf and if it is a
NULL pointer then we do the ice_construct_skb, otherwise we add a frag
to the current skb via ice_add_rx_frag. Then, on the ice_put_rx_buf the
skb pointer that belongs to rx_buf will be cleared. Moving further, if
the current frame is not EOP frame we assign the current skb to the
rx_buf that is pointed by updated next_to_clean indicator.

What is more during the buffer reuse let's assign each member of
ice_rx_buf individually so we avoid the unnecessary copy of skb.

Last but not least, this logic split will allow us for better code reuse
when adding a support for build_skb.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Pull out the code responsible for page counting and buffer recycling so
that it will be possible to clean up the Rx buffers in cases where we
won't allocate skb (ex. XDP)
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

{get,put}_page are atomic operations which we use for page count
handling. The current logic for refcount handling is that we increment
it when passing a skb with the data from the first half of page up to
netstack and recycle the second half of page. This operation protects us
from losing a page since the network stack can decrement the refcount of
page from skb.

The performance can be gently improved by doing the bulk updates of
refcount instead of doing it one by one. During the buffer initialization,
maximize the page's refcount and don't allow the refcount to become
less than two.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Instead of adding a frag and later when dealing with EOP frame accessing
that frag in order to copy the headers onto linear part of skb, we can do
this in ice_add_rx_frag in case where the data_len is still 0 and frame
won't fit onto the linear part as a whole.

Function comment of ice_pull_tail was a bit misleading because of
mentioned optimizations that can be performed (drop a frag/maintaining
accurate truesize of skb) - it seems that this part of logic was dropped
and the comment was not updated to reflect this change.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Introduce ice_can_reuse_rx_page which will verify whether the page can
be reused and return the boolean result to caller.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Introduce ice_get_rx_buf, which will fetch the Rx buffer and do the DMA
synchronization. Length of the packet that hardware Rx descriptor
contains is now read in ice_clean_rx_irq, so we can feed ice_get_rx_buf
with it and resign from rx_desc passed as argument in ice_fetch_rx_buf
and ice_add_rx_frag.
Signed-off-by: NMaciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware now supports link events over the admin receive queue (ARQ),
so enable HW link events over the ARQ and remove code for link event
polling.
Signed-off-by: NBrett Creeley <brett.creeley@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Someone went through the effort of making this a variable so let's use
it instead of recalculating it again.
Signed-off-by: NAlan Brady <alan.brady@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The VLAN rule is lost when VM starts or the AVF driver (iavf.ko) is
reloaded. So it is necessary to add this rule again.
Signed-off-by: NMichal Swiatkowski <michal.swiatkowski@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When VSI increases the number of queues dynamically, the scheduler
just needs to add the new required nodes rather than re-adjusting with
previously allocated number of nodes. Readjusting didn't provide enough
parents to add the upper layer nodes also can't place lan and rdma
subtrees separately.

In decrease case, keep the VSI configuration with max number of queues
always. This will leave some extra nodes in the tree but no harm done.
Signed-off-by: NVictor Raj <victor.raj@intel.com>
Reviewed-by: NBruce Allan <bruce.w.allan@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch changes how we get VF VSIs instances. Instead of relying on
mailbox virtual channel message to retrieve VSI, it is more reliable
getting it directly via VF object in PF data structure.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Don't let the VF know it's not trusted when it tries to add more than
permitted additional MAC addresses.
Signed-off-by: NAkeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>