Some devices with a builtin panel have the panel mounted upside down,
this is indicated by the rotate_180 bit in the BDB_GENERAL_FEATURES VBT
block.

We store this info in dev_priv->vbt.orientation, use this to set the
connector's orientation property so that fbcon and userspace will show
the image the right way up on devices with an upside-down mounted panel.

This fixes the image being upside-down on a Teclast X89 tablet.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228114110.187792-3-hdegoede@redhat.com

Commit 82daca29 ("drm/i915: Add "panel orientation" property to the
panel connector, v6.") uses hardware state readback to determine if the
GOP is rotating the image by 180 degrees to compensate for upside-down
mounted panels.

When I wrote that commit I tried to find the VBT bits the GOP used to
decide to rotate the image, but I could not find them. Back then I only
looked at the rotation bits in struct mipi_config and these read 0 on
the 1 BYT device I have with an upside-down mounted panel
(a GP-electronic T701 tablet). While working on a similar problem on a
BYT device with an eDP panel I noticed that the new
intel_dsi_get_panel_orientation() helper which gets used on newer
SoCs (Apollo-Lake, etc.) checks the rotate_180 bit in the
BDB_GENERAL_FEATURES VBT block.

I've checked and this bit indeed is set on the GP-electronic T701 tablet,
so using the generic intel_dsi_get_panel_orientation() helper there does
the right thing without needing any extra readback of hw state.

This commit removes the special handling of the panel orientation for
DSI panels on BYT/CHT devices, bringing the handling in line with the
handling of DSI panels on other devices.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228114110.187792-2-hdegoede@redhat.com

Unused since commit f97108d1 ("drm/i915: add dynamic performance
control support for Ironlake"). That's a little over ten years. Good
riddance.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227170047.31089-2-jani.nikula@intel.com

Keep reducing i915_drv.h.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227170047.31089-1-jani.nikula@intel.com

Finish the job started in d28ae3b2 ("drm/i915: split out
intel_dram.[ch] from i915_drv.c") by moving struct dram_dimm_info and
dram_channel_info inside intel_dram.c, the only user of the structs.
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227145359.17543-1-jani.nikula@intel.com

Having an array pipe_crc[I915_MAX_PIPES] in struct drm_i915_private
should be an obvious clue this should be located in struct intel_crtc
instead. Make it so.

As a side-effect, fix some errors in indexing pipe_crc with both pipe
and crtc index. And, of course, reduce the size of i915_drv.h.

Cc: Anshuman Gupta <anshuman.gupta@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227161253.15741-1-jani.nikula@intel.com

We monitor the health of the system via periodic heartbeat pulses. The
pulses also provide the opportunity to perform garbage collection.
However, we interpret an incomplete pulse (a missed heartbeat) as an
indication that the system is no longer responsive, i.e. hung, and
perform an engine or full GPU reset. Given that the preemption
granularity can be very coarse on a system, we let the sysadmin override
our legacy timeouts which were "optimised" for desktop applications.

The heartbeat interval can be adjusted per-engine using,

	/sys/class/drm/card?/engine/*/heartbeat_interval_ms
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NSteve Carbonari <steven.carbonari@intel.com>
Tested-by: NSteve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-7-chris@chris-wilson.co.uk

After initialising a preemption request, we give the current resident a
small amount of time to vacate the GPU. The preemption request is for a
higher priority context and should be immediate to maintain high
quality of service (and avoid priority inversion). However, the
preemption granularity of the GPU can be quite coarse and so we need a
compromise.

The preempt timeout can be adjusted per-engine using,

	/sys/class/drm/card?/engine/*/preempt_timeout_ms

and can be disabled by setting it to 0.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NSteve Carbonari <steven.carbonari@intel.com>
Tested-by: NSteve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-6-chris@chris-wilson.co.uk

When we allow ourselves to sleep before a GPU reset after disabling
submission, even for a few milliseconds, gives an innocent context the
opportunity to clear the GPU before the reset occurs. However, how long
to sleep depends on the typical non-preemptible duration (a similar
problem to determining the ideal preempt-reset timeout or even the
heartbeat interval). As this seems of a hard policy decision, punt it to
userspace.

The timeout can be adjusted using

	/sys/class/drm/card?/engine/*/stop_timeout_ms
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Reviewed-by: NSteve Carbonari <steven.carbonari@intel.com>
Tested-by: NSteve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-5-chris@chris-wilson.co.uk

We busywait on an inflight request (one that is currently executing on
HW, and so might complete quickly) prior to setting up an interrupt and
sleeping. The trade off is that we keep an expensive CPU core busy in
order to avoid wake up latency: where that trade off should lie is best
left to the sysadmin.

The busywait mechanism can be compiled out with

	./scripts/config --set-val DRM_I915_SPIN_REQUEST 0

The maximum busywait duration can be adjusted per-engine using,

	/sys/class/drm/card?/engine/*/ms_busywait_duration_ns
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NSteve Carbonari <steven.carbonari@intel.com>
Tested-by: NSteve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-4-chris@chris-wilson.co.uk

Execlists uses a scheduling quantum (a timeslice) to alternate execution
between ready-to-run contexts of equal priority. This ensures that all
users (though only if they of equal importance) have the opportunity to
run and prevents livelocks where contexts may have implicit ordering due
to userspace semaphores.

The timeslicing mechanism can be compiled out with

	./scripts/config --set-val DRM_I915_TIMESLICE_DURATION 0

The timeslice duration can be adjusted per-engine using,

	/sys/class/drm/card?/engine/*/timeslice_duration_ms
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Reviewed-by: NSteve Carbonari <steven.carbonari@intel.com>
Tested-by: NSteve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-3-chris@chris-wilson.co.uk

Use the per-engine sysfs directory to let userspace discover the
mmio_base of each engine. Prior to recent generations, the user
accessible registers on each engine are at a fixed offset relative to
each engine -- but require absolute addressing. As the absolute address
depends on the actual physical engine, this is not always possible to
determine from userspace (for example icl may expose vcs1 or vcs2 as the
second vcs engine). Make this easy for userspace to discover by
providing the mmio_base in sysfs.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Acked-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NSteve Carbonari <steven.carbonari@intel.com>
Tested-by: NSteve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-2-chris@chris-wilson.co.uk

Preliminary stub to add engines underneath /sys/class/drm/cardN/, so
that we can expose properties on each engine to the sysadmin.

To start with we have basic analogues of the i915_query ioctl so that we
can pretty print engine discovery from the shell, and flesh out the
directory structure. Later we will add writeable sysadmin properties such
as per-engine timeout controls.

An example tree of the engine properties on Braswell:
    /sys/class/drm/card0
    └── engine
        ├── bcs0
        │   ├── capabilities
        │   ├── class
        │   ├── instance
        │   ├── known_capabilities
        │   └── name
        ├── rcs0
        │   ├── capabilities
        │   ├── class
        │   ├── instance
        │   ├── known_capabilities
        │   └── name
        ├── vcs0
        │   ├── capabilities
        │   ├── class
        │   ├── instance
        │   ├── known_capabilities
        │   └── name
        └── vecs0
            ├── capabilities
            ├── class
            ├── instance
            ├── known_capabilities
            └── name

v2: Include stringified capabilities
v3: Include all known capabilities for futureproofing.
v4: Combine the two caps loops into one

v5: Hide underneath Kconfig.unstable for wider discussion
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Daniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Acked-by: NRodrigo Vivi <rodrigo.vivi@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Tested-by: NSteve Carbonari <steven.carbonari@intel.com>
Reviewed-by: NSteve Carbonari <steven.carbonari@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228131716.3243616-1-chris@chris-wilson.co.uk

The assert_mmap_offset() returns type bool so if we return an error
pointer that is "return true;" or success.  If we have an error, then
we should return false.

Fixes: 3d81d589 ("drm/i915: Test exhaustion of the mmap space")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228141413.qfjf4abr323drlo4@kili.mountain

WaDDIIOTimeout is only for A1 (pre-prod) glk steppings. Nuke it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-3-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

TGL+ supposedly do not need Wa_1405510057 so limit it to
gen11 only.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-2-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

w/a #1139 is only needed for pre-production GLK. Nuke it.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-1-ville.syrjala@linux.intel.comReviewed-by: NImre Deak <imre.deak@intel.com>

An odd and highly unlikely path caught us out. On delayed submission
(due to an asynchronous reset handler), we poked the priority_hint and
kicked the tasklet. However, we had already marked the device as wedged
and swapped out the tasklet for a no-op. The result was that we never
cleared the priority hint and became upset when we later checked.

<0> [574.303565] i915_sel-6278    2.... 481822445us : __i915_subtests: Running intel_execlists_live_selftests/live_error_interrupt
<0> [574.303565] i915_sel-6278    2.... 481822472us : __engine_unpark: 0000:00:02.0 rcs0:
<0> [574.303565] i915_sel-6278    2.... 481822491us : __gt_unpark: 0000:00:02.0
<0> [574.303565] i915_sel-6278    2.... 481823220us : execlists_context_reset: 0000:00:02.0 rcs0: context:f4ee reset
<0> [574.303565] i915_sel-6278    2.... 481824830us : __intel_context_active: 0000:00:02.0 rcs0: context:f51b active
<0> [574.303565] i915_sel-6278    2.... 481825258us : __intel_context_do_pin: 0000:00:02.0 rcs0: context:f51b pin ring:{start:00006000, head:0000, tail:0000}
<0> [574.303565] i915_sel-6278    2.... 481825311us : __i915_request_commit: 0000:00:02.0 rcs0: fence f51b:2, current 0
<0> [574.303565] i915_sel-6278    2d..1 481825347us : __i915_request_submit: 0000:00:02.0 rcs0: fence f51b:2, current 0
<0> [574.303565] i915_sel-6278    2d..1 481825363us : trace_ports: 0000:00:02.0 rcs0: submit { f51b:2, 0:0 }
<0> [574.303565] i915_sel-6278    2.... 481826809us : __intel_context_active: 0000:00:02.0 rcs0: context:f51c active
<0> [574.303565]   <idle>-0       7d.h2 481827326us : cs_irq_handler: 0000:00:02.0 rcs0: CS error: 1
<0> [574.303565]   <idle>-0       7..s1 481827377us : process_csb: 0000:00:02.0 rcs0: cs-irq head=3, tail=4
<0> [574.303565]   <idle>-0       7..s1 481827379us : process_csb: 0000:00:02.0 rcs0: csb[4]: status=0x10000001:0x00000000
<0> [574.305593]   <idle>-0       7..s1 481827385us : trace_ports: 0000:00:02.0 rcs0: promote { f51b:2*, 0:0 }
<0> [574.305611]   <idle>-0       7..s1 481828179us : execlists_reset: 0000:00:02.0 rcs0: reset for CS error
<0> [574.305611] i915_sel-6278    2.... 481828284us : __intel_context_do_pin: 0000:00:02.0 rcs0: context:f51c pin ring:{start:00007000, head:0000, tail:0000}
<0> [574.305611] i915_sel-6278    2.... 481828345us : __i915_request_commit: 0000:00:02.0 rcs0: fence f51c:2, current 0
<0> [574.305611]   <idle>-0       7dNs2 481847823us : __i915_request_unsubmit: 0000:00:02.0 rcs0: fence f51b:2, current 1
<0> [574.305611]   <idle>-0       7dNs2 481847857us : execlists_hold: 0000:00:02.0 rcs0: fence f51b:2, current 1 on hold
<0> [574.305611]   <idle>-0       7.Ns1 481847863us : intel_engine_reset: 0000:00:02.0 rcs0: flags=4
<0> [574.305611]   <idle>-0       7.Ns1 481847945us : execlists_reset_prepare: 0000:00:02.0 rcs0: depth<-1
<0> [574.305611]   <idle>-0       7.Ns1 481847946us : intel_engine_stop_cs: 0000:00:02.0 rcs0:
<0> [574.305611]   <idle>-0       7.Ns1 538584284us : intel_engine_stop_cs: 0000:00:02.0 rcs0: timed out on STOP_RING -> IDLE
<0> [574.305611]   <idle>-0       7.Ns1 538584347us : __intel_gt_reset: 0000:00:02.0 engine_mask=1
<0> [574.305611]   <idle>-0       7.Ns1 538584406us : execlists_reset_rewind: 0000:00:02.0 rcs0:
<0> [574.305611]   <idle>-0       7dNs2 538585050us : __i915_request_reset: 0000:00:02.0 rcs0: fence f51b:2, current 1 guilty? yes
<0> [574.305611]   <idle>-0       7dNs2 538585063us : __execlists_reset: 0000:00:02.0 rcs0: replay {head:0000, tail:0068}
<0> [574.306565]   <idle>-0       7.Ns1 538588457us : intel_engine_cancel_stop_cs: 0000:00:02.0 rcs0:
<0> [574.306565]   <idle>-0       7dNs2 538588462us : __i915_request_submit: 0000:00:02.0 rcs0: fence f51c:2, current 0
<0> [574.306565]   <idle>-0       7dNs2 538588471us : trace_ports: 0000:00:02.0 rcs0: submit { f51c:2, 0:0 }
<0> [574.306565]   <idle>-0       7.Ns1 538588474us : execlists_reset_finish: 0000:00:02.0 rcs0: depth->1
<0> [574.306565] kworker/-202     2.... 538588755us : i915_request_retire: 0000:00:02.0 rcs0: fence f51c:2, current 2
<0> [574.306565] ksoftirq-46      7..s. 538588773us : process_csb: 0000:00:02.0 rcs0: cs-irq head=11, tail=1
<0> [574.306565] ksoftirq-46      7..s. 538588774us : process_csb: 0000:00:02.0 rcs0: csb[0]: status=0x10000001:0x00000000
<0> [574.306565] ksoftirq-46      7..s. 538588776us : trace_ports: 0000:00:02.0 rcs0: promote { f51c:2!, 0:0 }
<0> [574.306565] ksoftirq-46      7..s. 538588778us : process_csb: 0000:00:02.0 rcs0: csb[1]: status=0x10000018:0x00000020
<0> [574.306565] ksoftirq-46      7..s. 538588779us : trace_ports: 0000:00:02.0 rcs0: completed { f51c:2!, 0:0 }
<0> [574.306565] kworker/-202     2.... 538588826us : intel_context_unpin: 0000:00:02.0 rcs0: context:f51c unpin
<0> [574.306565] i915_sel-6278    6.... 538589663us : __intel_gt_set_wedged.part.32: 0000:00:02.0 start
<0> [574.306565] i915_sel-6278    6.... 538589667us : execlists_reset_prepare: 0000:00:02.0 rcs0: depth<-0
<0> [574.306565] i915_sel-6278    6.... 538589710us : intel_engine_stop_cs: 0000:00:02.0 rcs0:
<0> [574.306565] i915_sel-6278    6.... 538589732us : execlists_reset_prepare: 0000:00:02.0 bcs0: depth<-0
<0> [574.307591] i915_sel-6278    6.... 538589733us : intel_engine_stop_cs: 0000:00:02.0 bcs0:
<0> [574.307591] i915_sel-6278    6.... 538589757us : execlists_reset_prepare: 0000:00:02.0 vcs0: depth<-0
<0> [574.307591] i915_sel-6278    6.... 538589758us : intel_engine_stop_cs: 0000:00:02.0 vcs0:
<0> [574.307591] i915_sel-6278    6.... 538589771us : execlists_reset_prepare: 0000:00:02.0 vcs1: depth<-0
<0> [574.307591] i915_sel-6278    6.... 538589772us : intel_engine_stop_cs: 0000:00:02.0 vcs1:
<0> [574.307591] i915_sel-6278    6.... 538589778us : execlists_reset_prepare: 0000:00:02.0 vecs0: depth<-0
<0> [574.307591] i915_sel-6278    6.... 538589780us : intel_engine_stop_cs: 0000:00:02.0 vecs0:
<0> [574.307591] i915_sel-6278    6.... 538589786us : __intel_gt_reset: 0000:00:02.0 engine_mask=ff
<0> [574.307591] i915_sel-6278    6.... 538591175us : execlists_reset_cancel: 0000:00:02.0 rcs0:
<0> [574.307591] i915_sel-6278    6.... 538591970us : execlists_reset_cancel: 0000:00:02.0 bcs0:
<0> [574.307591] i915_sel-6278    6.... 538591982us : execlists_reset_cancel: 0000:00:02.0 vcs0:
<0> [574.307591] i915_sel-6278    6.... 538591996us : execlists_reset_cancel: 0000:00:02.0 vcs1:
<0> [574.307591] i915_sel-6278    6.... 538592759us : execlists_reset_cancel: 0000:00:02.0 vecs0:
<0> [574.307591] i915_sel-6278    6.... 538592977us : execlists_reset_finish: 0000:00:02.0 rcs0: depth->0
<0> [574.307591] i915_sel-6278    6.N.. 538592996us : execlists_reset_finish: 0000:00:02.0 bcs0: depth->0
<0> [574.307591] i915_sel-6278    6.N.. 538593023us : execlists_reset_finish: 0000:00:02.0 vcs0: depth->0
<0> [574.307591] i915_sel-6278    6.N.. 538593037us : execlists_reset_finish: 0000:00:02.0 vcs1: depth->0
<0> [574.307591] i915_sel-6278    6.N.. 538593051us : execlists_reset_finish: 0000:00:02.0 vecs0: depth->0
<0> [574.307591] i915_sel-6278    6.... 538593407us : __intel_gt_set_wedged.part.32: 0000:00:02.0 end
<0> [574.307591] kworker/-210     7d..1 551958381us : execlists_unhold: 0000:00:02.0 rcs0: fence f51b:2, current 2 hold release
<0> [574.307591] i915_sel-6278    0.... 559490788us : i915_request_retire: 0000:00:02.0 rcs0: fence f51b:2, current 2
<0> [574.307591] i915_sel-6278    0.... 559490793us : intel_context_unpin: 0000:00:02.0 rcs0: context:f51b unpin
<0> [574.307591] i915_sel-6278    0.... 559490798us : __engine_park: 0000:00:02.0 rcs0: parked
<0> [574.307591] i915_sel-6278    0.... 559490982us : __intel_context_retire: 0000:00:02.0 rcs0: context:f51c retire runtime: { total:30004ns, avg:30004ns }
<0> [574.307591] i915_sel-6278    0.... 559491372us : __engine_park: __engine_park:261 GEM_BUG_ON(engine->execlists.queue_priority_hint != (-((int)(~0U >> 1)) - 1))
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-9-chris@chris-wilson.co.uk

Give the reset worker a kick before losing help when waiting for hang
recovery, as the CPU scheduler is a little unreliable.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-15-chris@chris-wilson.co.uk

Detect GLK pre-production steppings. Not 100% of A2 being pre-prod
since the spec is a bit of a mess but feels more or less correct.
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200128155152.21977-4-ville.syrjala@linux.intel.comAcked-by: NChris Wilson <chris@chris-wilson.co.uk>

As we require a context switch to ensure that the current context is
switched out and saved to memory, perform an explicit switch to the
kernel context and wait for it.

Closes: https://gitlab.freedesktop.org/drm/intel/issues/1336Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200228082330.2411941-18-chris@chris-wilson.co.uk

The engine->kernel_context is a special case for request emission. Since
it is used as the barrier within the engine's wakeref, we must acquire the
wakeref before submitting a request to the kernel_context.
Reported-by: NLionel Landwerlin <lionel.g.landwerlin@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-3-chris@chris-wilson.co.uk

Inside the general i915_oa_init_reg_state() we avoid using the
perf->mutex. However, we rely on perf->exclusive_stream being valid to
access at that point, and for that we have to control the race with
disabling perf. This relies on the disabling being a heavy barrier that
inspects all active contexts, after marking the perf->exclusive_stream
as not available. This should ensure that there are no more concurrent
accesses to the perf->exclusive_stream as we destroy it.

Mark up the races around the perf->exclusive_stream so that they stand
out much more. (And hopefully we will be running kcsan to start
validating that the only races we have are carefully controlled.)
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-2-chris@chris-wilson.co.uk

As a disabled pipe in pipe_mask is not having a valid intel crtc,
driver wrongly populates the possible_crtcs mask while initializing
the plane for a CRTC. Fixing up the plane possible_crtcs mask.

changes since RFC:
- Simplify the possible_crtcs initialization. [Ville]
v2:
- Removed the unnecessary stack garbage possible_crtcs to
  drm_universal_plane_init. [Ville]
v3:
- Combine the intel_crtc assignment and declaration. [Ville]
v4:
- Fix possible_crtcs abused bits from
  intel_{primary,curosr,sprite}_plane_create(). [Ville]

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NAnshuman Gupta <anshuman.gupta@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226163517.31234-1-anshuman.gupta@intel.com

We need to be extremely careful inside i915_request_await_start() as it
needs to walk the list of requests in the foreign timeline with very
little protection. As we hold our own timeline mutex, we can not nest
inside the signaler's timeline mutex, so all that remains is our RCU
protection. However, to be safe we need to tell the compiler that we may
be traversing the list only under RCU protection, and furthermore we
need to start declaring requests as elements of the timeline from their
construction.

Fixes: 9ddc8ec0 ("drm/i915: Eliminate the trylock for awaiting an earlier request")
Fixes: 6a79d848 ("drm/i915: Lock signaler timeline while navigating")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-11-chris@chris-wilson.co.uk

Check that we can recover if the LRC is totally corrupted. Based on a
very simple theory that anything that can be adjusted via the context
(i.e. on behalf of the user), should be under the purview of the
per-engine-reset.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-13-chris@chris-wilson.co.uk

Record the LRC registers before/after a preemption event to ensure that
the first context sees nothing from the second client; at least in the
normal per-context register state.

References: https://gitlab.freedesktop.org/drm/intel/issues/1233Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-12-chris@chris-wilson.co.uk

Pull the final atomic_dec of vm->open (marking the vm as closed)
underneath the same vm->mutex as used to close it. This is required to
correctly serialise with attempting to reuse the vma as the vm is closed
by a second thread.

References: 00de702c ("drm/i915: Check that the vma hasn't been closed before we insert it")
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-10-chris@chris-wilson.co.uk

As we drop the engine-pm on retiring, that may happen while there are
still CS events in the buffer. As such we cannot assert the engine is
still active on reset, until we know that the current request is still
in flight.

Closes: https://gitlab.freedesktop.org/drm/intel/issues/1338Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NAndi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227204727.2009346-1-chris@chris-wilson.co.uk

Still chasing the mystery of the stray idle flush, let's ensure that the
heartbeat does not run at the same time as our test and confuse us.

References: https://gitlab.freedesktop.org/drm/intel/issues/541Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NAndi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-8-chris@chris-wilson.co.uk

Attaching to the i915_active barrier is a two stage process, and a flush
is only effective when the barrier is activation. Thus it is possible
for us to see a barrier, and attempt to flush, only for our flush to
have no effect. As such, before attempting to activate signaling on the
fence we need to double check it is a fence!

Fixes: d13a3177 ("drm/i915: Flush idle barriers when waiting")
Closes: https://gitlab.freedesktop.org/drm/intel/issues/1333Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NAndi Shyti <andi.shyti@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200227085723.1961649-1-chris@chris-wilson.co.uk

On TGL, bits 2-4 in the GGTT PTE are not ignored anymore and are
instead used for some extra VT-d capabilities. We don't (yet?) have
support for those capabilities, but, given that we shared the pte_encode
function betweed GGTT and PPGTT, we still set those bits to the PPGTT
PPAT values. The DMA engine gets very confused when those bits are
set while the iommu is enabled, leading to errors. E.g. when loading
the GuC we get:

[    9.796218] DMAR: DRHD: handling fault status reg 2
[    9.796235] DMAR: [DMA Write] Request device [00:02.0] PASID ffffffff fault addr 0 [fault reason 02] Present bit in context entry is clear
[    9.899215] [drm:intel_guc_fw_upload [i915]] *ERROR* GuC firmware signature verification failed

To fix this, just have dedicated gen8_pte_encode function per type of
gtt. Also, explicitly set vm->pte_encode for gen8_ppgtt, even if we
don't use it, to make sure we don't accidentally assign it to the GGTT
one, like we do for gen6_ppgtt, in case we need it in the future.
Reported-by: N"Sodhi, Vunny" <vunny.sodhi@intel.com>
Signed-off-by: NDaniele Ceraolo Spurio <daniele.ceraolospurio@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@linux.intel.com>
Cc: Matthew Auld <matthew.auld@intel.com>
Cc: Michal Wajdeczko <michal.wajdeczko@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@linux.intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226185657.26445-1-daniele.ceraolospurio@intel.com

Wa_1608008084 is an additional WA that applies to writes on FF_MODE2
register. We can't read it back either from CPU or GPU. Since the other
bits should be 0, recommendation to handle Wa_1604555607 is to actually
just write the timer value.

Do a write only and don't try to read it, neither before or after
the WA is applied.

Fixes: ff690b21 ("drm/i915/tgl: Implement Wa_1604555607")
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224191258.15668-1-lucas.demarchi@intel.com

Looks like the pipe rounding mode bit has moved from PIPE_CHICKEN to
PIPE_MISC on tgl. Frob the new location.

Bspec does still document the old bits as well, so I left the code
for them as is until we get clarification from the hw folks on
whether the old bits still do something useful.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200226163054.9509-1-ville.syrjala@linux.intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>

This register was placed in the middle of the PP_STATUS definition
instead of together with the PP_CONTROL where it should. Since it's not
used and there are no current plans to use it, just remove the
definition.

v2: remove the define rather than moving it.
Signed-off-by: NLucas De Marchi <lucas.demarchi@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190308232321.30168-1-lucas.demarchi@intel.com

The implicit "dev_priv" local variable use has been a long-standing pain
point in the register access macros I915_READ(), I915_WRITE(),
POSTING_READ(), I915_READ_FW(), and I915_WRITE_FW().

Replace the sole remaining I915_WRITE() in i915_drv.c with
intel_uncore_write(), although it might be better to keep the entire
file void of direct register access.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225111509.21879-3-jani.nikula@intel.com

The implicit "dev_priv" local variable use has been a long-standing pain
point in the register access macros I915_READ(), I915_WRITE(),
POSTING_READ(), I915_READ_FW(), and I915_WRITE_FW().

Replace them with the corresponding uncore register accessors
intel_uncore_read(), intel_uncore_write(), intel_uncore_posting_read(),
intel_uncore_read_fw(), and intel_uncore_write_fw().

Rename dev_priv to i915 while at it.

No functional changes.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225111509.21879-2-jani.nikula@intel.com

The DRAM related routines are pretty isolated from the rest of the
i915_drv.c, split it out to a separate file. Put the eDRAM stuff in the
same bag, and rename the visible functions to have intel_dram_
prefix. Do some benign whitespace fixes and dev_priv -> i915 conversions
while at it.
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225111509.21879-1-jani.nikula@intel.com

The #include has been splattered all over the place, but there are
precious few places, all .c files, that actually need it.

v2: remove leftover double newlines
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200225133131.3301-1-jani.nikula@intel.com

On Tiger Lake we do not support source keying in the pixel formats P010,
P012, P016.

v2: Move WA to end of function. Create helper function for format
check. Less verbose debugging messaging.

v3: whitespace

v4(MattR):
 - Actually return EINVAL to reject this combination.
 - Pass format parameter as u32.
 - Make test TGL-specific for now.
 - Switch to per-device logging.
 - Shorten/simplify comment.

Bspec: 52890
Cc: Matt Roper <matthew.d.roper@intel.com>
Cc: Manasi Navare <manasi.d.navare@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NMatt Atwood <matthew.s.atwood@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20200224223651.3801646-1-matthew.d.roper@intel.comReviewed-by: NJosé Roberto de Souza <jose.souza@intel.com>