An errata with GLQF_PCNT causes it to not wrap as expected. This
can cause an error in flow director statistics. This patch resets
affected counters just after reading.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Fortville and Fort Park devices are often on different firmware release
schedules. This change relaxes the minor version warning message,
so it is only displayed for older FW warning version for old
firmware Fortville 3 or earlier.
Signed-off-by: NMariusz Stachura <mariusz.stachura@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This commit replaces usage of vsi->back in i40e_print_link_message()
(which is actually a PF pointer) with temp variable.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

i40e_print_link_message() is intended to compare new
link state with current link state and print log message
only if the new state is different from current state.

However in current driver the new state does not get updated
when link is going down because of the if condition. When an
interface is brought down, vsi->state is set to I40E_VSI_DOWN
in i40e_vsi_close() and later i40e_print_link_message() does
not get invoked in i40e_link_event due to if condition. Hence
link down message doesn't appear when link is going down. The
down state is seen  later during i40e_open() and old state
gets printed. The actual link state doesn't get updated in
i40e_close() or i40e_open() but when i40e_handle_link_event is
called inside i40e_clean_adminq_subtask.

This change allows i40e_print_link_message() to be called when
interface is going down and keeps the state information updated.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

In current driver, when ifconfig ethx up is done, the link state
doesn't transition to UP inside i40e_open(). It changes after AQ
command response is handled in i40e_handle_link_event().

When pf->hw.phy.link_info.link_info is DOWN inside i40e_open(),
The state is transient and invalid. So log message gets printed
based on incorrect info (i.e link_info and an_info).

This commit removes check for unqualified module inside
i40e_up_complete(). The existing check in i40e_handle_link_event()
logs the error message based on correct link state information.
Signed-off-by: NSudheer Mogilappagari <sudheer.mogilappagari@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

This value is not calculating bytes_per_int, which would actually just
be bytes/ITR_COUNTDOWN_START, but rather it's calculating bytes/usecs.

Rename the variable for clarity so that future developers understand
what the value is actually calculating.
Signed-off-by: NJacob Keller <jacob.e.keller@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

When using lldptool to configure DCB parameter, hclge_dcb module
call the client_ops->setup_tc to tell network stack which queue
and priority is using for specific tc.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After the DCB feature is supported, fc_mode and dcb enable flag
must be set according to the DCB parameter.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add dcb netlink interface by calling the interface from
hclge_dcb module.

This patch also update Makefile in order to build hns3_dcbnl module.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hclge_dcb module calls the interface from hclge_main/tm
and provide interface for the dcb netlink interface.

This patch also update Makefiles required to build the DCB
supported code in HNS3 Ethernet driver and update the existing
Kconfig file in the hisilicon folder.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add some interface and export some interface from
hclge_tm and hclgc_main to support the upcoming DCB feature.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When sriov is enabled and TM is in tc-based mode, vf's TM
parameters is not set in TM initialization process.
This patch add the tc_based TM support for sriov enabled
using the information in vport struct.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add a tm_port_shaper cmd and set port shaper
to HCLGE_ETHER_MAX_RATE on TM initialization process.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add a pfc_pause_en cmd, and use it to configure
PFC option according to fc_mode in hdev->tm_info.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Current buffer allocation can only happen at init, when
doing buffer reallocation after init, care must be taken
care of memory which priv_buf points to.
This patch fixes it by using a dynamic allocated temporary
memory. Because we only do buffer reallocation at init or
when setting up the DCB parameter, and priv_buf is only
used at buffer allocation process, so it is ok to use a
dynamic allocated temporary memory.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch add support of dynamically assigning tx buffer to
TC when the TC is enabled.
It will save buffer for rx direction to avoid packet loss.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix the following scenario:
1. tx_free_poll is running on cpu X
2. xmit function is running on cpu Y and fails to get sq wqe
3. tx_free_poll frees wqes on cpu X and checks the queue is not stopped
4. xmit function stops the queue after failed to get sq wqe
5. The queue is stopped forever
Signed-off-by: NAviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set Rxq irq to specific cpu for allocating and receiving the skb from
the same node.
Signed-off-by: NAviad Krawczyk <aviad.krawczyk@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function ch_flower_stats_cb is local to the source and does not need
to be in global scope, so make it static.

Cleans up sparse warnings:
symbol 'ch_flower_stats_cb' was not declared. Should it be static?
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Make the Spectrum router logic not ignore the RTNL_FAMILY_IPMR FIB
notifications.

Past commits added the IPMR VIF and MFC add/del notifications via the
fib_notifier chain. In addition, a code for handling these notifications in
the Spectrum router logic was added. Make the Spectrum router logic not
ignore these notifications and forward the requests to the Spectrum
multicast router offloading logic.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Due to the fact that multicast routes hold the minimum MTU of all the
egress RIFs and trap packets that don't meet it, notify the mulitcast
router code on RIF MTU changes.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add functionality for calling the multicast routing offloading logic upon
MFC and VIF add and delete notifications. In addition, call the multicast
routing upon RIF addition and deletion events.

As the multicast routing offload logic may sleep, the actual calls are done
in a deferred work. To ensure the MFC object is not freed in that interval,
a reference is held to it. In case of a failure, the abort mechanism is
used, which ejects all the routes from the hardware and triggers the
traffic to flow through the kernel.

Note: At that stage, the FIB notifications are still ignored, and will be
enabled in a further patch.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently, the mlxsw Spectrum driver offloads only either the RT_TABLE_MAIN
FIB table or the VRF tables, so the RT_TABLE_LOCAL table is squashed to the
RT_TABLE_MAIN table to allow local routes to be offloaded too.

By default, multicast MFC routes which are not assigned to any user
requested table are put in the RT_TABLE_DEFAULT table.

Due to the fact that offloading multicast MFC routes support in Spectrum
router logic is going to be introduced soon, squash the default table to
MAIN too.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the multicast routing hardware API introduced in previous patch
for the specific spectrum hardware.

The spectrum hardware multicast routes are written using the RMFT2 register
and point to an ACL flexible action set. The actions used for multicast
routes are:
 - Counter action, which allows counting bytes and packets on multicast
   routes.
 - Multicast route action, which provide RPF check and do the actual packet
   duplication to a list of RIFs.
 - Trap action, in the case the route action specified by the called is
   trap.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add the multicast router offloading logic, which is in charge of handling
the VIF and MFC notifications and translating it to the hardware logic API.

The offloading logic has to overcome several obstacles in order to safely
comply with the kernel multicast router user API:
 - It must keep track of the mapping between VIFs to netdevices. The user
   can add an MFC cache entry pointing to a VIF, delete the VIF and add
   re-add it with a different netdevice. The offloading logic has to handle
   this in order to be compatible with the kernel logic.
 - It must keep track of the mapping between netdevices to spectrum RIFs,
   as the current hardware implementation assume having a RIF for every
   port in a multicast router.
 - It must handle routes pointing to pimreg device to be trapped to the
   kernel, as the packet should be delivered to userspace.
 - It must handle routes pointing tunnel VIFs. The current implementation
   does not support multicast forwarding to tunnels, thus routes that point
   to a tunnel should be trapped to the kernel.
 - It must be aware of proxy multicast routes, which include both (*,*)
   routes and duplicate routes. Currently proxy routes are not offloaded
   and trigger the abort mechanism: removal of all routes from hardware and
   triggering the traffic to go through the kernel.

The multicast routing offloading logic also updates the counters of the
offloaded MFC routes in a periodic work.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Periodically receive messages containing the destination IPs of tunnels
that have recently forwarded traffic. Update the neighbour entries 'used'
value for these IPs next hop.

This prevents the neighbour entry from expiring on timeout but rather
signals an ARP to verify the connection. From an NFP perspective, packets
will not fall back mid-flow unless the link is verified to be down.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Receive a request when the NFP does not know the next hop for a packet
that is to be encapsulated in a VXLAN tunnel. Do a route lookup, determine
the next hop entry and update neighbour table on NFP. Monitor the kernel
neighbour table for link changes and update NFP with relevant information.
Overwrite routes with zero values on the NFP when they expire.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Maintain a list of IPv4 addresses used as the tunnel destination IP match
fields in currently active flower rules. Offload the entire list of
NFP_FL_IPV4_ADDRS_MAX (even if some are unused) when new IPs are added or
removed. The NFP should only be aware of tunnel end points that are
currently used by rules on the device
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generate a list of MAC addresses of netdevs that could be used as VXLAN
tunnel end points. Give offloaded MACs an index for storage on the NFP in
the ranges:
0x100-0x1ff physical port representors
0x200-0x2ff VF port representors
0x300-0x3ff other offloads (e.g. vxlan netdevs, ovs bridges)

Assign phys and vf indexes based on unique 8 bit values in the port num.
Maintain list of other netdevs to ensure same netdev is not offloaded
twice and each gets a unique ID without exhausting the entries. Because
the IDs are unique but constant for a netdev, any changes are implemented
by overwriting the index on NFP.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile set tunnel actions for tc flower. Only support VXLAN and ensure a
tunnel destination port of 4789 is used.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Compile ovs-tc flower vxlan metadata match fields for offloading. Only
support offload of tunnel data when the VXLAN port specifically matches
well known port 4789.
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add a helper function that returns the length of the cmsg data when given
the cmsg skb
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Signed-off-by: NSimon Horman <simon.horman@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If action is "gact_ok", offload it to HW.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate error instead of doing WARN_ON right away.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for controlling nexthop counters via dpipe.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for adjacency table dump.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add support for setting counters on nexthops based on dpipe's adjacency
table counter status. This patch also adds the ability for getting the
counter value, which will be used by the dpipe adjacency table dump
implementation in the next patches.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to add the ability for setting counters on nexthops the RATR
register should be extended.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add initial support for router adjacency table. The table does lookup
based on the nexthop-group index and the local nexthop offset. After
locating the nexthop entry it sets the destination MAC address and the
egress RIF.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is done as a preparation before introducing the ability to dump the
adjacency table via dpipe, and to count the table size. The current table
implementation avoids tunnel entries, thus a helper for checking if
the nexthop group contains tunnel entries is also provided. The mlxsw's
nexthop representative struct stays private to the router module.
Signed-off-by: NArkadi Sharshevsky <arkadis@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>