This patch removes the extra compatibility string "st,stm32-usart" to
avoid confusion, save some time & space.
Signed-off-by: NVikas Manocha <vikas.manocha@st.com>
Reviewed-by: NPatrice Chotard <patrice.chotard@st.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The atmel serial port driver reported the following warning on suspend:
atmel_usart f8020000.serial: ttyS1: Unable to drain transmitter

As the ATMEL_US_TXEMPTY status bit in ATMEL_US_CSR is always cleared
when the transmitter is disabled, we need to know the transmitter's
state to return the real fifo state. And as ATMEL_US_CR is write-only,
it is necessary to save the state of the transmitter in a local
variable, and update the variable when TXEN and TXDIS is written in
ATMEL_US_CR.

After those changes, atmel_tx_empty can return "empty" on suspend, the
warning in uart_suspend_port disappears, and suspending is 20ms shorter
for each enabled Atmel serial port.
Signed-off-by: NRomain Izard <romain.izard.pro@gmail.com>
Tested-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

HSCIF has facilities that allow changing the timeout after which an RX
interrupt is triggered even if the FIFO is not filled. This patch allows
changing the default (15 bits of silence) using the existing sysfs
attribute "rx_fifo_timeout".
Signed-off-by: NUlrich Hecht <ulrich.hecht+renesas@gmail.com>
Reviewed-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch fixes the checkpatch.pl error complain:

ERROR: space required before the open brace '{'
Signed-off-by: NGimcuan Hui <gimcuan@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch is fix the warning reported by smatch as following:

drivers/tty/serial/8250/8250_fintek.c:294 fintek_8250_goto_highspeed()
warn: inconsistent indenting
Signed-off-by: NJi-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The F81216H had 4 clocksource 1.8432/18.432/14.769/24MHzand  baud rates can
be up to 1.5Mbits with 24MHz. The register value and mask is the same with
F81866. But F81866 register address is F2h, F81216H is F0h.

We'll implements the dynamic clocksource in fintek_8250_set_termios().
Signed-off-by: NJi-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The F81866 had 4 clocksource 1.8432/18.432/14.769/24MHz and baud rates can
be up to 1.5Mbits with 24MHz. We'll implements the dynamic clocksource in
fintek_8250_set_termios().
Signed-off-by: NJi-Ze Hong (Peter Hong) <hpeter+linux_kernel@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

    Use setup_timer function instead of initializing timer with the
    function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

        Use setup_timer function instead of initializing timer with the
        function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

        Use setup_timer function instead of initializing timer with the
        function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

        Use setup_timer function instead of initializing timer with the
        function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

    Use setup_timer function instead of initializing timer with the
    function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

    Use setup_timer function instead of initializing timer with the
    function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

    Use setup_timer function instead of initializing timer with the
    function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

    Use setup_timer function instead of initializing timer with the
    function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

    Use setup_timer function instead of initializing timer with the
    function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The variable "dma_is_txing" is an unsigned int, set as either "0" or "1"
in all but one location, where it is instead set to "false". For
consistency, set dma_is_txing to "0" in this location too.
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The imx serial driver uses PAGE_SIZE when allocating rx_buf, but then
uses RX_BUF_SIZE (which is currently defined as PAGE_SIZE) to describe
the length of the buffer when initialising the scatter gather list.

In order to ensure that this stays consistent, use RX_BUF_SIZE in both
locations.
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Acked-by: NUwe Kleine-König <u.kleine-könig@pengtronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The variable dma_is_rxing is currently set to 1 in imx_disable_rx_int().
This is problematic as:

- whilst imx_disable_rx_int() is currently always called before
  start_rx_dma() this dependency isn't obvious.
- start_rx_dma() does error checking and might exit without
  enabling DMA. Currently this will result in dma_is_rxing suggesting
  that DMA is being used for recieving.

To avoid these issues, move the setting of dma_is_rxing to
start_rx_dma() when appropriate.
Signed-off-by: NRomain Perier <romain.perier@collabora.com>
Signed-off-by: NMartyn Welch <martyn.welch@collabora.co.uk>
Reviewed-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

    Use setup_timer function instead of initializing timer with the
    function and data fields.
Signed-off-by: NAllen Pais <allen.lkml@gmail.com>
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

UART core function uart_update_mctrl relies on a cached value of
modem control lines. This was used but not updated by local RTS
control functions within imx.c. These are used for RS485 line
driver enable signalling. Having an out-of-date value in the cached
mctrl can result in the transmitter being enabled when it shouldn't
be.

Fix this by updating the mctrl value before applying it.
Signed-off-by: NIan Jamison <ian.dev@arkver.com>
Origin: id:8195c96e674517b82a6ff7fe914c7ba0f86e702b.1505375165.git.ian.dev@arkver.com
Acked-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: NClemens Gruber <clemens.gruber@pqgruber.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for the rs485 specific properties defined in
Documentation/devicetree/bindings/serial/rs485.txt.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Forwarded: id:20170913081833.2740-7-u.kleine-koenig@pengutronix.de (v5)
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The i.MX driver defaulted to full duplex rs485 which is rather
unusual and doesn't match the default implemented in other drivers.

So change the default to half duplex.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.

As a side effect this adds support for parsing rs485-rts-delay and
rs485-rx-during-tx. As the driver doesn't support this though, probing
fails if these are defined.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

We just got a common helper for parsing the rs485 specific
device tree properties. Use it and drop the open coded parser.

Note that there is a small difference between the removed and the now
used implementation: The former cleared flags to 0 if rs485-rts-delay
was given, the common helper clears SER_RS485_RX_DURING_TX and
SER_RS485_ENABLED only but always which makes more sense.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
[ukleinek: point out semantic change in commit log]
Acked-by: NNicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: NRichard Genoud <richard.genoud@gmail.com>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Several drivers have the same device tree parsing code. Create
a common helper function for it.

This patch bases on work done by Sascha Hauer.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit a6d7514b ("tty: serial: lpuart: add a more accurate baud
rate calculation method") the baud rate is now calculated inside the
lpuart32_serial_setbrg() function, so we no longer need to read the
UARTBAUD register inside lpuart32_set_termios().

The 'bd' variable can be simply removed.

This fixes the following build warning with W=1:

drivers/tty/serial/fsl_lpuart.c: In function 'lpuart32_set_termios':
drivers/tty/serial/fsl_lpuart.c:1652:32: warning: variable 'bd' set but not used [-Wunused-but-set-variable]

Fixes: a6d7514b ("tty: serial: lpuart: add a more accurate baud rate calculation method")
Signed-off-by: NFabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In order to avoid code duplication and to be more consistent with the
other error handling paths in this function, we should 'goto errout'.
Signed-off-by: NChristophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Use bsearch library function instead of duplicated functionality.
Signed-off-by: NThomas Meyer <thomas@m3y3r.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make this const as it is only stored in the const field 'ops' of an
uart_port structure. It is not referenced in any other file and therefore
make it static too.

Done using Coccinelle.
Signed-off-by: NBhumika Goyal <bhumirks@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix some minor typo spotted in comments:
- s/wit ha/with a/
- s/doestroyed/destroyed/
Signed-off-by: NAntonio Borneo <borneo.antonio@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This dirver try to implement the Magic SysRq support[1] for
Amlogic Inc's meson platfo
>From the hardware perspective, the UART IP can't detect the 'BREAK' command
clearly via the status register. Instead, we rely on the combination of
'FRAME_ERR bit && ch == 0', and it works fine.

[1] Documentation/admin-guide/sysrq.rst
Signed-off-by: NYixun Lan <dlan@gentoo.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull UBI updates from Richard Weinberger:
 "Minor improvements"

* tag 'upstream-4.14-rc1' of git://git.infradead.org/linux-ubifs:
  UBI: Fix two typos in comments
  ubi: fastmap: fix spelling mistake: "invalidiate" -> "invalidate"
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines
  ubi: pr_err() strings should end with newlines

Pull UML updates from Richard Weinberger:

 - minor improvements

 - fixes for Debian's new gcc defaults (pie enabled by default)

 - fixes for XSTATE/XSAVE to make UML work again on modern systems

* 'for-linus-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
  um: return negative in tuntap_open_tramp()
  um: remove a stray tab
  um: Use relative modversions with LD_SCRIPT_DYN
  um: link vmlinux with -no-pie
  um: Fix CONFIG_GCOV for modules.
  Fix minor typos and grammar in UML start_up help
  um: defconfig: Cleanup from old Kconfig options
  um: Fix FP register size for XSTATE/XSAVE

Pull networking fixes from David Miller:

 1) Fix hotplug deadlock in hv_netvsc, from Stephen Hemminger.

 2) Fix double-free in rmnet driver, from Dan Carpenter.

 3) INET connection socket layer can double put request sockets, fix
    from Eric Dumazet.

 4) Don't match collect metadata-mode tunnels if the device is down,
    from Haishuang Yan.

 5) Do not perform TSO6/GSO on ipv6 packets with extensions headers in
    be2net driver, from Suresh Reddy.

 6) Fix scaling error in gen_estimator, from Eric Dumazet.

 7) Fix 64-bit statistics deadlock in systemport driver, from Florian
    Fainelli.

 8) Fix use-after-free in sctp_sock_dump, from Xin Long.

 9) Reject invalid BPF_END instructions in verifier, from Edward Cree.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (43 commits)
  mlxsw: spectrum_router: Only handle IPv4 and IPv6 events
  Documentation: link in networking docs
  tcp: fix data delivery rate
  bpf/verifier: reject BPF_ALU64|BPF_END
  sctp: do not mark sk dumped when inet_sctp_diag_fill returns err
  sctp: fix an use-after-free issue in sctp_sock_dump
  netvsc: increase default receive buffer size
  tcp: update skb->skb_mstamp more carefully
  net: ipv4: fix l3slave check for index returned in IP_PKTINFO
  net: smsc911x: Quieten netif during suspend
  net: systemport: Fix 64-bit stats deadlock
  net: vrf: avoid gcc-4.6 warning
  qed: remove unnecessary call to memset
  tg3: clean up redundant initialization of tnapi
  tls: make tls_sw_free_resources static
  sctp: potential read out of bounds in sctp_ulpevent_type_enabled()
  MAINTAINERS: review Renesas DT bindings as well
  net_sched: gen_estimator: fix scaling error in bytes/packets samples
  nfp: wait for the NSP resource to appear on boot
  nfp: wait for board state before talking to the NSP
  ...

Pull more input updates from Dmitry Torokhov:
 "A second round of updates for the input subsystem:

   - a new driver for PWM-controlled vibrators

   - ucb1400 touchscreen driver had completely busted suspend/resume
     handling

   - we now handle "home" button found on some devices with Goodix
     touchscreens

   - assorted other fixups"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
  Input: i8042 - add Gigabyte P57 to the keyboard reset table
  Input: xpad - validate USB endpoint type during probe
  Input: ucb1400_ts - fix suspend and resume handling
  Input: edt-ft5x06 - fix access to non-existing register
  Input: elantech - make arrays debounce_packet static, reduces object code size
  Input: surface3_spi - make const array header static, reduces object code size
  Input: goodix - add support for capacitive home button
  Input: add a driver for PWM controllable vibrators
  Input: adi - make array seq static, reduces object code size

Commit 5620a0d1 ("firmware: delete in-kernel firmware") removed the
entire firmware directory.  Unfortunately it thereby also removed the
support for built-in firmware.

This restores the ability to build firmware directly into the kernel by
pruning the original Makefile to the necessary minimum.  The default for
EXTRA_FIRMWARE_DIR is now the standard directory /lib/firmware/.

Fixes: 5620a0d1 ("firmware: delete in-kernel firmware")
Signed-off-by: NMarkus Trippelsdorf <markus@trippelsdorf.de>
Acked-by: NGreg K-H <gregkh@linuxfoundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

The driver doesn't support events from address families other than IPv4
and IPv6, so ignore them. Otherwise, we risk queueing a work item before
it's initialized.

This can happen in case a VRF is configured when MROUTE_MULTIPLE_TABLES
is enabled, as the VRF driver will try to add an l3mdev rule for the
IPMR family.

Fixes: 65e65ec1 ("mlxsw: spectrum_router: Don't ignore IPv6 notifications")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reported-by: NAndreas Rammhold <andreas@rammhold.de>
Reported-by: NFlorian Klink <flokli@flokli.de>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>