Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 13 5月, 2009 9 次提交
    • A
      OMAP3 clock: lessen amount of noisy messages · 0db4e825
      由 Artem Bityutskiy 提交于 
      On our system we see the following messages:

Disabling unused clock "gpt2_ick"
Disabling unused clock "gpt3_ick"
Disabling unused clock "gpt4_ick"
Disabling unused clock "gpt5_ick"
...

The messages have KERN_INFO level and if you have serial
console, they normally go there. I do not think it is good
idea to print that much stuff there. Moreover, messages
are not properly prefixed and for mortals it is not
immeadietly clear where they come from.

Let's give them debugging level instead.
Signed-off-by: NArtem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
[paul@pwsan.com: trimmed debugging output in patch description]
      0db4e825
    • P
      OMAP3 clock: use pr_debug() rather than pr_info() in some clock change code · b7aee4bf
      由 Paul Walmsley 提交于 
      The CORE DPLL M2 frequency change code should use pr_debug(), not
pr_info(), for its debug messages.  Same with
omap2_clksel_round_rate_div().  While here, convert a few printk(KERN_ERR ..
into pr_err().
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      b7aee4bf
    • P
      OMAP3 clock: only unlock SDRC DLL if SDRC clk < 83MHz · 4519c2bf
      由 Paul Walmsley 提交于 
      According to the 34xx TRM Rev. K section 11.2.4.4.11.1 "Purpose of the
DLL/CDL Module," the SDRC delay-locked-loop can be locked at any SDRC
clock frequency from 83MHz to 166MHz.  CDP code unconditionally
unlocked the DLL whenever shifting to a lower SDRC speed, but this
seems unnecessary and error-prone, as the DLL is no longer able to
compensate for process, voltage, and temperature variations.  Instead,
only unlock the DLL when the SDRC clock rate would be less than 83MHz.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      4519c2bf
    • P
      OMAP3 SRAM: renumber registers to make space for argument passing · b2abb271
      由 Paul Walmsley 提交于 
      Renumber registers in omap3_sram_configure_core_dpll() assembly code to
make space for additional parameters.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      b2abb271
    • P
      OMAP3 SDRC: initialize SDRC_POWER at boot · 98cfe5ab
      由 Paul Walmsley 提交于 
      Initialize SDRC_POWER to a known-good setting when the kernel boots.
Necessary since some bootloaders don't initialize SDRC_POWER properly.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      98cfe5ab
    • P
      OMAP3 SRAM: clear the SDRC PWRENA bit during SDRC frequency change · fa0406a8
      由 Paul Walmsley 提交于 
      Clear the SDRC_POWER.PWRENA bit before putting the SDRAM into self-refresh
mode.  This prevents the SDRC from attempting to power off the SDRAM,
which can cause the system to hang.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      fa0406a8
    • P
      OMAP3 clock: add interconnect barriers to CORE DPLL M2 change · d75d9e73
      由 Paul Walmsley 提交于 
      Where necessary, add interconnect barriers to force posted writes to
complete before continuing.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
      d75d9e73
    • P
      OMAP3 SRAM: add ARM barriers to omap3_sram_configure_core_dpll · 69d4255b
      由 Paul Walmsley 提交于 
      Add more barriers in the SRAM CORE DPLL M2 divider change code.

- Add a DSB SY after the function's entry point to flush all cached
  and buffered writes and wait for the interconnect to claim that they
  have completed[1].  The idea here is to force all delayed write
  traffic going to the SDRAM to at least post to the L3 interconnect
  before continuing.  If these writes are allowed to occur after the
  SDRC is idled, the writes will not be acknowledged and the ARM will
  stall.

  Note that in this case, it does not matter if the writes actually
  complete to the SDRAM - it is only necessary for the writes to leave
  the ARM itself.  If the writes are posted by the interconnect when
  the SDRC goes into idle, the writes will be delayed until the SDRC
  returns from idle[2].  If the SDRC is in the middle of a write when
  it is requested to enter idle, the SDRC will not acknowledge the
  idle request until the writes complete to the SDRAM.[3]

  The old-style DMB in sdram_in_selfrefresh is now superfluous, so,
  remove it.

- Add an ISB before the function's exit point to prevent the ARM from
  speculatively executing into SDRAM before the SDRAM is enabled[4].

...

1. ARMv7 ARM (DDI 0406A) A3-47, A3-48.

2. Private communication with Richard Woodruff <r-woodruff2@ti.com>.

3. Private communication with Richard Woodruff <r-woodruff2@ti.com>.

4. ARMv7 ARM (DDI 0406A) A3-48.
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      69d4255b
    • P
      OMAP3 SRAM: mark OCM RAM as Non-cacheable Normal memory · d9295746
      由 Paul Walmsley 提交于 
      Mark the SRAM (aka OCM RAM) as Non-cacheable Normal memory[1].  This
is to prevent the ARM from evicting existing cache lines to SDRAM
while code is executing from the SRAM.  Necessary since one of the
primary uses for the SRAM is to hold the code and data for the CORE
DPLL M2 divider reprogramming code, which must execute while the SDRC
is idled.  If the ARM attempts to write cache lines back to the while
the SRAM code is running, the ARM will stall[2].

TI deals with this problem in the CDP kernel by marking the SRAM as
Strongly-ordered memory.

Tero Kristo <tero.kristo@nokia.com> caught a bug in an earlier version of
this patch - thanks Tero.

...

1. ARMv7 ARM (DDI 0406A) pp. A3-30, A3-31, B3-32.

2. Private communication with Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: NPaul Walmsley <paul@pwsan.com>
Cc: Tero Kristo <tero.kristo@nokia.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
      d9295746
  3. 12 5月, 2009 11 次提交
  5. 11 5月, 2009 9 次提交
  7. 10 5月, 2009 11 次提交