The initial skb may have been freed after napi_gro_complete in
napi_gro_receive if it was merged into an existing packet.  Thus
we cannot check same_flow (which indicates whether it was merged)
after calling napi_gro_complete.

This patch fixes this by saving the same_flow status before the
call to napi_gro_complete.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When AN is enabled and the link is down the speed/duplex control bits
will not be meaningful.  Use the advertising bits instead, and mask
them with the LPA bits if and only if AN is complete (as before).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This should reduce user confusion and may also aid recovery (ioctls
will still be available).
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The SFT9001 firmware implements cable diagnostics; run those and
include their results in a self-test.  In case of a cable fault, do
not fail the self-test as a whole; only faults in the NIC should cause
that.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Pass in ethtool test flags to determine which tests to run.
Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

802.3ad has its own ethhdr-like structure in the form of an ad_header,
which is at the start of both the LACPDU and marker PDU.  Both are
the same from the struct values, both are packed as well.

It's therefore perfectly fine to replace the ad_header by the ethhdr
and to remove its definition.
Signed-off-by: NHolger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Generalize out mac address initializer for the LACPDU multicast
address and use in two places.  Remove the now unused
AD_MULTICAST_LACPDU_ADDR.
Signed-off-by: NHolger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Save some text by initializing ports LACPDU from const initializer,
then get rid of ad_initialize_lacpdu().
Signed-off-by: NHolger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As typedefs are considered a bad thing most of the time remove the
typedef around ad_system.
Signed-off-by: NHolger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turn ports is_individual into a bool.  There is no functional change.
Signed-off-by: NHolger Eitzenberger <heitzenberger@astaro.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turn ports is_enabled into a bool.  There is no functional change.
Signed-off-by: NHolger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Turn Need-To-Transmit port variable into a bool.  There is no
functional change.
Signed-off-by: NHolger Eitzenberger <holger@eitzenberger.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The adapter rings are kcalloc()'d, but in set_ringparam() in ixgbe_ethtool,
we replace that memory from the vmalloc() pool.  This can result in a NULL
pointer reference when trying to modify the rings at a later time, or on
device removal.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change allows DCB mode to change the number of queues, and presumably
the number of NAPI instances, safely.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The recent GRO patches introduced the NAPI removal of devices in
free_netdev.  For drivers that can change the number of queues during
driver operation, the NAPI infrastructure doesn't allow the freeing and
re-addition of NAPI entities without reloading the driver.

This change reinitializes the dev_list in each NAPI struct on delete,
instead of just deleting it (and assigning the list pointers to POISON).
Drivers that wish to remove/re-add NAPI will need to re-initialize the
netdev napi_list after removing all NAPI instances, before re-adding NAPI
devices again.
Signed-off-by: NPeter P Waskiewicz Jr <peter.p.waskiewicz.jr@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The 82576 adapter orders the queues in pairs when virtualization is in use.
The queue ordering previously conflicted with the ordering when sr-iov was
enabled.  This new ordering allows a PF to allocate 2 queues without using
any VF resources.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes tx head writeback as it was found to not provide a
significant improvement in tx performance and on some systems has been seen
to cause a performance degredation due to partial cache line writes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes a useless ret variable from the IPv4 ESP/UDP
decapsulation code.
Signed-off-by: NHerbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch simply reorders some functions to eliminate the need for
forward references. No other changes than that.
Suggested-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NAnton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This adds basic support for the 'Solos' PCI ADSL2+ cards being developed
by Traverse Technologies and Xrio Ltd:
http://www.traverse.com.au/productview.php?product_id=116Signed-off-by: NNathan Williams <nathan@traverse.com.au>
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove unnecessary #ifdef-s and #if-0-ed code sections.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Switch from private printk wrapper macros to using pr_err() and
pr_info() from linux/kernel.h, at the same time unifying a few
error messages.
Signed-off-by: NTilman Schmidt <tilman@imap.cc>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update contol path between cxgb3 and ULP modules (iWARP, iSCSI)
to provide access to firware and protocol engine info.
Signed-off-by: NDivy Le Ray <divy@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/wireless/prism54/islpci_hotplug.c:97:1: warning: symbol 'prism54_probe' was not declared. Should it be static?
  drivers/net/wireless/prism54/islpci_hotplug.c:220:1: warning: symbol 'prism54_remove' was not declared. Should it be static?
  drivers/net/wireless/prism54/islpci_hotplug.c:263:1: warning: symbol 'prism54_suspend' was not declared. Should it be static?
  drivers/net/wireless/prism54/islpci_hotplug.c:286:1: warning: symbol 'prism54_resume' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/wireless/ipw2x00/ipw2100.c:5271:6: warning: symbol 'ipw2100_queues_initialize' was not declared. Should it be static?
  drivers/net/wireless/ipw2x00/ipw2100.c:5278:6: warning: symbol 'ipw2100_queues_free' was not declared. Should it be static?
  drivers/net/wireless/ipw2x00/ipw2100.c:5285:5: warning: symbol 'ipw2100_queues_allocate' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/wireless/b43/phy_a.c:80:6: warning: symbol 'b43_radio_set_tx_iq' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_a.c:150:6: warning: symbol 'b43_radio_init2060' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_g.c:57:10: warning: symbol 'b43_radio_channel_codes_bg' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_g.c:218:6: warning: symbol 'b43_set_txpower_g' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_g.c:386:6: warning: symbol 'b43_nrssi_hw_write' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_g.c:393:5: warning: symbol 'b43_nrssi_hw_read' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_g.c:404:6: warning: symbol 'b43_nrssi_hw_update' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_g.c:418:6: warning: symbol 'b43_nrssi_mem_update' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_g.c:592:6: warning: symbol 'b43_calc_nrssi_slope' was not declared. Should it be static?
  drivers/net/wireless/b43/phy_g.c:1357:5: warning: symbol 'b43_radio_init2050' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/wireless/ath9k/eeprom.c:195:6: warning: symbol 'ath9k_fill_eeprom' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:463:5: warning: symbol 'ath9k_check_eeprom' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:1219:6: warning: symbol 'ath9k_hw_set_def_power_per_rate_table' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:1510:6: warning: symbol 'ath9k_hw_set_4k_power_per_rate_table' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:2007:5: warning: symbol 'ath9k_set_txpower' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:2106:6: warning: symbol 'ath9k_set_addac' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:2543:6: warning: symbol 'ath9k_eeprom_set_board_values' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:2606:5: warning: symbol 'ath9k_get_eeprom_antenna_cfg' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:2622:4: warning: symbol 'ath9k_hw_get_4k_num_ant_config' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:2628:4: warning: symbol 'ath9k_hw_get_def_num_ant_config' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:2647:4: warning: symbol 'ath9k_get_num_ant_config' was not declared. Should it be static?
  drivers/net/wireless/ath9k/eeprom.c:2790:5: warning: symbol 'ath9k_get_eeprom' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/wireless/airo.c:3610:6: warning: symbol 'mpi_receive_802_11' was not declared. Should it be static?
  drivers/net/wireless/atmel.c:3183:6: warning: symbol 'atmel_join_bss' was not declared. Should it be static?
  drivers/net/wireless/ray_cs.c:831:5: warning: symbol 'ray_dev_init' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The symbols are only references within the translation unit they are
defined in, so un-EXPORT them und make them 'static'.

Fix this sparse warnings:

  drivers/net/wan/z85230.c:604:25: warning: symbol 'z8530_dma_sync' was not declared. Should it be static?
  drivers/net/wan/z85230.c:613:25: warning: symbol 'z8530_txdma_sync' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warning:

  drivers/net/wan/x25_asy.c:623:5: warning: symbol 'x25_asy_esc' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/wan/wanxl.c:414:3: warning: do-while statement is not a compound statement
  drivers/net/wan/wanxl.c:441:3: warning: do-while statement is not a compound statement
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/tulip/de2104x.c:1695:4: warning: do-while statement is not a compound statement
  drivers/net/tulip/tulip_core.c:1433:5: warning: do-while statement is not a compound statement
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/tokenring/ibmtr.c:1840:6: warning: symbol 'tok_rerun' was not declared. Should it be static?
  drivers/net/tokenring/madgemc.c:469:16: warning: symbol 'madgemc_setnselout_pins' was not declared. Should it be static?
  drivers/net/tokenring/proteon.c:286:16: warning: symbol 'proteon_setnselout_pins' was not declared. Should it be static?
  drivers/net/tokenring/skisa.c:303:16: warning: symbol 'sk_isa_setnselout_pins' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/skfp/skfddi.c:620:13: warning: symbol 'skfp_interrupt' was not declared. Should it be static?
  drivers/net/skfp/skfddi.c:687:25: warning: symbol 'skfp_ctl_get_stats' was not declared. Should it be static?
  drivers/net/skfp/skfddi.c:1232:6: warning: symbol 'CheckSourceAddress' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/qlge/qlge_ethtool.c:100:6: warning: symbol 'ql_update_stats' was not declared. Should it be static?
  drivers/net/qlge/qlge_mpi.c:22:5: warning: symbol 'ql_get_mb_sts' was not declared. Should it be static?
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix this sparse warnings:

  drivers/net/netxen/netxen_nic_hw.c:1462:18: warning: Using plain integer as NULL pointer
  drivers/net/netxen/netxen_nic_hw.c:1536:18: warning: Using plain integer as NULL pointer
Signed-off-by: NHannes Eder <hannes@hanneseder.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>