On powerpc, probing on emulate_step function will crash 2.6.18.1 when
it is triggered.

When kprobe is triggered, emulate_step() is on its kernel path and
will cause recursive kprobe fault.  And branch_taken() is called
in emulate_step().  This disallows kprobes on both of them.
Signed-off-by: NPaul Mackerras <paulus@samba.org>

If mmiowb() is always used prior to releasing spinlock as Doc suggests,
then it's safe against preemption; but I'm not convinced that's always
the case.  If preemption occurs between sync and get_paca()->io_sync = 0,
I believe there's no problem.  But in the unlikely event that gcc does
the store relative to another register than r13 (as it did with current),
then there's a small danger of setting another cpu's io_sync to 0, after
it had just set it to 1.  Rewrite ppc64 mmiowb to prevent that.

The remaining io_sync assignments in io.h all get_paca()->io_sync = 1,
which is harmless even if preempted to the wrong cpu (the context switch
itself syncs); and those in spinlock.h are while preemption is disabled.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Checking source for other get_paca()->field preemption dangers found that
open_high_hpage_areas does a structure copy into its paca while preemption
is enabled: unsafe however gcc accomplishes it.  Just remove that copy:
it's done safely afterwards by on_each_cpu, as in open_low_hpage_areas.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Acked-by: NDavid Gibson <dwg@au1.ibm.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Repeated -j20 kernel builds on a G5 Quad running an SMP PREEMPT kernel
would often collapse within a day, some exec failing with "Bad address".
In each case examined, load_elf_binary was doing a kernel_read, but
generic_file_aio_read's access_ok saw current->thread.fs.seg as USER_DS
instead of KERNEL_DS.

objdump of filemap.o shows gcc 4.1.0 emitting "mr r5,r13 ... ld r9,416(r5)"
here for get_paca()->__current, instead of the expected and much more usual
"ld r9,416(r13)"; I've seen other gcc4s do the same, but perhaps not gcc3s.

So, if the task is preempted and rescheduled on a different cpu in between
the mr and the ld, r5 will be looking at a different paca_struct from the
one it's now on, pick up the wrong __current, and perhaps the wrong seg.
Presumably much worse could happen elsewhere, though that split is rare.

Other architectures appear to be safe (x86_64's read_pda is more limiting
than get_paca), but ppc64 needs to force "current" into one instruction.
Signed-off-by: NHugh Dickins <hugh@veritas.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Changed qe_issue_cmd() to write cmd_input to the CECDR unmodified.  It
was treating cmd_input as a virtual address and tried to convert it to
a physical address.
Signed-off-by: NTimur Tabi <timur@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The 10Gigabit ethernet device drivers appear to be able to chew
up all 256MB of TCE mappings on pSeries systems, as evidenced by
numerous error messages:

 iommu_alloc failed, tbl c0000000010d5c48 vaddr c0000000d875eff0 npages 1

Some experimentation indicates that this is essentially because
one 1500 byte ethernet MTU gets mapped as a 64K DMA region when
the large 64K pages are enabled. Thus, it doesn't take much to
exhaust all of the available DMA mappings for a high-speed card.

This patch changes the iommu allocator to work with its own
unique, distinct page size. Although the patch is long, its
actually quite simple: it just #defines a distinct IOMMU_PAGE_SIZE
and then uses this in all the places that matter.

As a side effect, it also dramatically improves network performance
on platforms with H-calls on iommu translation inserts/removes (since
we no longer call it 16 times for a 1500 bytes packet when the iommu HW
is still 4k).

In the future, we might want to make the IOMMU_PAGE_SIZE a variable
in the iommu_table instance, thus allowing support for different HW
page sizes in the iommu itself.
Signed-off-by: NLinas Vepstas <linas@austin.ibm.com>
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: NOlof Johansson <olof@lixom.net>
Acked-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

Fixed a compile error in building the 85xx support with oprofile, and in
the process cleaned up some issues with the fsl_booke performance monitor
code.

* Reorganized FSL Book-E performance monitoring code so that the 7450
  wouldn't be built if the e500 was, and cleaned it up so it was more
  self-contained.

* Added a cpu_setup function for FSL Book-E.  The original
  cpu_setup function prototype had no arguments, assuming that
  the reg_setup function would copy the required information into
  variables which represented the registers.  This was silly for
  e500, since it has 1 register per counter (rather than 3 for
  all counters), so the code has been restructured to have
  cpu_setup take the current counter config array as an argument,
  with op_powerpc_setup() invoking op_powerpc_cpu_setup() through
  on_each_cpu(), and op_powerpc_cpu_setup() invoking the
  model-specific cpu_setup function with an argument.  The
  argument is ignored on all other platforms at present.

* Fixed a confusing line where a trinary operator only had two
  arguments
Signed-off-by: NAndrew Fleming <afleming@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

The e500 core generates an illegal instruction exception when it tries
to execute the lwsync instruction, which we currently use for rmb().
This fixes it by using the LWSYNC macro, which turns into a plain sync
on 32-bit machines.
Signed-off-by: NAndrew Fleming <afleming@freescale.com>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

This patch fixes a few issues in offb:

 - A test was inverted causing the palette hack to never work
(no device node was passed down to the init function)

 - Some cards seem to have their assigned-addresses property in a random
order, thus we need to try using of_get_pci_address() first, which will
fail if it's not a PCI device, and fallback to of_get_address() in that
case. of_get_pci_address() properly parsees assigned-addresses to test
the BAR number and thus will get it right whatever the order is.

 - Some cards (like GXT4500) provide a linebytes of 0xffffffff in the
device-tree which does no good. This patch handles that by using the
screen width when that happens. (Also fixes btext.c while at it).

 - Add detection of the GXT4500 in addition to the GXT2000 for the
palette hacks (we use the same hack, palette is linear in register space
at offset 0x6000).
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NPaul Mackerras <paulus@samba.org>

* 'release' of master.kernel.org:/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] Correct definition of handle_IPI
  [IA64] move SAL_CACHE_FLUSH check later in boot
  [IA64] MCA recovery: Montecito support
  [IA64] cpu-hotplug: Fixing confliction between CPU hot-add and IPI
  [IA64] don't double >> PAGE_SHIFT pointer for /dev/kmem access

The declaration of handle_IPI in arch/ia64/kernel/smp.c was changed but
not the definition of this function.  Remove struct pt_regs from
handle_IPI().
Signed-off-by: NKeith Owens <kaos@sgi.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The check to see if the firmware drops interrupts during a
SAL_CACHE_FLUSH is done to early in the boot. SAL_CACHE_FLUSH expects
to be able to make PAL calls in virtual mode, on some cell based
machines a fault occurs causing a MCA. This patch moves the check
after mmu_context_init so the TLB and VHPT are properly setup.

Signed-off-by Troy Heber <troy.heber@hp.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

The information in MCA records is filled in slightly differently on
Montecito than on Madison/McKinley.  Usually, the cache check and bus
check target identifiers have the same address.   On Montecito the
cache check and bus check target identifiers can be different if 
a corrected error (ie SBE or unconsumed poison data) was encountered and
then an uncorrected error (ie DBE) was consumed.  In that case, the 
cache check target identifier is the physical address of the DBE (that
caused the MCA to surface) while the bus check target identifier is the 
physical address of the SBE.  This patch correctly finds the target
identifier that triggered the MCA.

If there are multiple valid cache target identifiers in the same
error record then use the one with the lowest cache level.

Signed-off-by: Russ Anderson (rja@sgi.com)
Signed-off-by: NTony Luck <tony.luck@intel.com>

Signed-off-by: NKenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Acked-by: NSatoru Takeuchi <takeuchi_satoru@jp.fujitsu.com>
Acked-by: NKAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: NTony Luck <tony.luck@intel.com>

Since we already moved to GENERIC_TIME, we should implement alternatives
of old do_gettimeoffset routines to get sub-jiffies resolution from
gettimeofday().  This patch includes:

 * MIPS clocksource support (based on works by Manish Lachwani).
 * remove unused gettimeoffset routines and related codes.
 * remove unised 64bit do_div64_32().
 * simplify mips_hpt_init. (no argument needed, __init tag)
 * simplify c0_hpt_timer_init. (no need to write to c0_count)
 * remove some hpt_init routines.
 * mips_hpt_mask variable to specify bitmask of hpt value.
 * convert jmr3927_do_gettimeoffset to jmr3927_hpt_read.
 * convert ip27_do_gettimeoffset to ip27_hpt_read.
 * convert bcm1480_do_gettimeoffset to bcm1480_hpt_read.
 * simplify sb1250 hpt functions. (no need to subtract and shift)
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

arch/mips/kernel/traps.c:1115: warning: int format, long unsigned int arg (arg 2)
Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NYoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NManish Lachwani <mlachwani@mvista.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

SCSI_QLA_ISCSI needs to depend on NET to prevent build (link) failures
that are caused by selecting SCSI_ISCSI_ATTRS.
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

In very rare circumstances would we be pruning a merged request and at
the same time delete the implicated cfqq from the rr_list, and not readd
it when the merged request got added. This could cause io stalls until
that process issued io again.

Fix it up by putting the rr_list add handling into cfq_add_rq_rb(),
identical to how pruning is handled in cfq_del_rq_rb(). This fixes a
hang reproducible with fsx-linux.
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

* master.kernel.org:/pub/scm/linux/kernel/git/lethal/sh-2.6:
  sh: Titan defconfig update.
  sh: Fix IPR-IRQ's for IRQ-chip change breakage.
  sh: Update r7780rp_defconfig.
  video: Fix include in hp680_bl.
  sh: Wire up new syscalls.

* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
  [IPV6]: fix flowlabel seqfile handling
  [IPV6]: return EINVAL for invalid address with flowlabel lease request
  [SCTP]: Remove temporary associations from backlog and hash.
  [SCTP]: Correctly set IP id for SCTP traffic
  [NetLabel]: protect the CIPSOv4 socket option from setsockopt()
  [NETFILTER]: ip_tables: compat code module refcounting fix
  [NETFILTER]: nf_conntrack: add missing unlock in get_next_corpse()
  [NETFILTER]: ip_tables: compat error way cleanup
  [NETFILTER]: Missed and reordered checks in {arp,ip,ip6}_tables
  [NETFILTER]: remove masq/NAT from ip6tables Kconfig help
  [IPV6]: fix lockup via /proc/net/ip6_flowlabel
  [NET]: fix uaccess handling
  [SCTP]: Always linearise packet on input
  [ETH1394]: Fix unaligned accesses.
  [DCCP]: fix printk format warnings
  [NET]: Fix segmentation of linear packets
  [XFRM] xfrm_user: Fix unaligned accesses.
  [APPLETALK]: Fix potential OOPS in atalk_sendmsg().
  [NET] sealevel: uses arp_broken_ops

* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
  [SPARC64]: Add some missing print_symbol() calls.
  [SPARC64]: Fix Tomatillo/Schizo IRQ handling.

Partitions are not limited to live within a device.  So we should range
check after partition mapping.

Note that 'maxsector' was being used for two different things.  I have
split off the second usage into 'old_sector' so that maxsector can be still
be used for it's primary usage later in the function.

Cc: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: NNeil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix the use of dget/dput calls to balance out on the lower filesystem.
Signed-off-by: NMichael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

There is no point to calling the lower umount_begin when the eCryptfs
umount_begin is called.
Signed-off-by: NMichael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Opens on lower dentry objects happen in several places in eCryptfs, and they
all involve the same steps (dget, mntget, dentry_open).  This patch
consolidates the lower open events into a single function call.
Signed-off-by: NMichael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update cipher block encryption code to the new crypto API.
Signed-off-by: NMichael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Update eCryptfs hash code to the new kernel crypto API.
Signed-off-by: NMichael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Clean up the crypto initialization code; let the crypto API take care of the
key size checks.
Signed-off-by: NMichael Halcrow <mhalcrow@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

If there are no listeners, taskstats_exit_send() just returns because
taskstats_exit_alloc() didn't allocate *tidstats.  This is wrong, each
sub-thread should do fill_tgid_exit() on exit, otherwise its ->delays is
not recorded in ->signal->stats and lost.

Q: We don't send TASKSTATS_TYPE_AGGR_TGID when single-threaded process
exits.  Is it good?  How can the listener figure out that it was actually a
process exit, not sub-thread?
Signed-off-by: NOleg Nesterov <oleg@tv-sign.ru>
Cc: Balbir Singh <balbir@in.ibm.com>
Acked-by: NShailabh Nagar <nagar@watson.ibm.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

This is the UML piece of the INITCALLS tidying.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

kallsyms now refers to addresses as '_text + 0xADDRESS', rather than just
'0xADDRESS', so we need to define _text.
Signed-off-by: NJeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

Fix a small memory leak in ubd_config, and clearify the confusion which lead
to it.

Then, some little changes not affecting operations -
* move init functions together,
* add a comment about a potential problem in case of some evolution in the block layer,
* mark all initcalls as static __init functions
* mark an used once little function as inline
* document that mconsole methods are all called in process context (was
  triggered when checking ubd mconsole methods).
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>

To simplify error handling, make sure fd is saved into ubd_dev->fd only when
we are sure it is an fd and not an error code.
Signed-off-by: NPaolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: NAndrew Morton <akpm@osdl.org>
Signed-off-by: NLinus Torvalds <torvalds@osdl.org>