The generic USB serial code is ill-suited for high-speed USB wwan devices,
resulting in the option driver. However, other non-option devices may also
gain similar benefits from not using the generic code. Factorise out the
non-option specific code from the option driver and make it available to
other users.
Signed-off-by: NMatthew Garrett <mjg@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

All unsuccessful (non-zero status) URBs were being dropped. After N_IN_URBs are
dropped you will no longer be able to receive data.

This patch resubmits unsuccessful URBs unless the status indicates that it should
be terminated. The statuses that indicate the URB should be terminated was
gathered from other similar drivers.
Signed-off-by: NJames Maki <jamescmaki@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Remove unnecessary comments stating function names at (some)
opening/closing braces.
Fix some whitespace issues.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Generalise write buffer preparation.

This allows for drivers to manipulate (e.g. add headers) to bulk out
data before it is sent.

This adds a new function pointer to usb_serial_driver:

int (*prepare_write_buffer)(struct usb_serial_port *port,
		void **dest, size_t size, const void *src, size_t count);

The function is generic and can be used with either kfifo-based or
multi-urb writes:

If *dest is NULL the implementation should allocate dest.
If src is NULL the implementation should use the port write fifo.

If not set, a generic implementation is used which simply uses memcpy or
kfifo_out.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use dynamic transfer buffer sizes since it is more efficient to let the
host controller do the partitioning to fit endpoint size. This way we
also do not use more than one urb per write request.

Replace max_in_flight_urbs with multi_urb_write flag in struct
usb_serial_driver to enable multi-urb writes.

Use MAX_TX_URBS=40 and a max buffer size of PAGE_SIZE to prevent DoS
attacks.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow drivers to implement their own multi-urb write bulk callbacks as
we do for single urb writes.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the generic kfifo-based write implementation rather than allowing up
to 4000 8 byte urbs in the host stack queues.

Cc: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use usb_serial_generic_close to kill the read and write urbs and to
reset the write fifo.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace custom fifo-based write implementation with the generic
kfifo-based one.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Submit write urb if it is not already in use and we have buffered data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Clean up error messages on usb_submit_urb failure.
Remove debug message on zero-length writes.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Switch to generic read implementation and use process_read_urb to do
device specific processing (handle line status).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow drivers to use the generic throttle and unthrottle implementation.
This makes sense for drivers using the generic read functionality.

Note that drivers need to set these explicitly in order to enable them
(i.e., we do not set them at port probe if not defined).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use generic read implementation and use process_read_urb to do device
specific processing (handle line status).
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add process_read_urb to usb_serial_driver so that a driver can rely on
the generic read (and throttle) mechanism but still do device specific
processing of incoming data (such as adding tty_flags before pushing to
line discipline).

The default generic implementation handles sysrq for consoles but
otherwise simply pushes to tty.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Always process and flush read urb, but only resubmit when not throttled.
The new tty-layer supply plenty of slack so there is really no need to
cache and delay processing of a single urb while throttled.

Note that unthrottle now submits using GFP_KERNEL as we are not in
atomic context (so there is no need to save irq state either).

Note also that the process_read_urb function could be added to
usb_serial_driver should any driver need to do any device specific
processing.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There is no need to initialise the read urb as this is done at port
probe.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The generic read and write bulk urbs are initialised when allocated in
usb_serial_probe. The only field that needs to be updated after that is
the transfer_buffer_length of the write urb.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Use the already exported function for submitting the read urb associated
with a usb_serial_port.

Make sure it returns the result of usb_submit_urb and rename to the
more descriptive usb_serial_generic_submit_read_urb.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Export usb_serial_generic_close so that drivers can easily kill the read
and write urb and make sure that the write fifo is reset.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure fifo is emptied on close.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

On errors the fifo was reset without any locking. This could race with
write which do kfifo_put and perhaps also chars_in_buffer and write_room.

Every other access to the fifo is protected using the port lock so
better add it to the error path as well.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Make sure chars_in_buffer accounts also for data in host stack queues.

This fixes the problem with tty_wait_until_sent returning too soon at
close which could cause the final write urb to be cancelled.
Reported-by: NPete Zaitcev <zaitcev@redhat.com>
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The pl2303 requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Increase the bulk-out buffer size from 64 to 256 byte.

This gives a significant increase in throughput already at 1Mbaud as well
as lowered CPU usage. The buffer is big enough to keep up also at 3Mbaud
(128b would not suffice).

        64b         256b
921k:   640 KB/s    870 KB/s
3M:     640 KB/s    2520 KB/s
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The cp210x requires a bulk-in buffer larger than endpoint size to keep
up at high baudrates without loosing data.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Increase the bulk-out buffer size from 64 to 256 byte.

This gives a significant increase in throughput already at 1Mbaud
(e.g. 710 instead of 640 KB/s) as well as lowered CPU usage.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Allow drivers to define custom bulk in/out buffer sizes in struct
usb_serial_driver. If not set, fall back to the default buffer size
which matches the endpoint size.

Three drivers are currently freeing the pre-allocated buffers and
allocating larger ones to achieve this at port probe (ftdi_sio) or even
at port open (ipaq and iuu_phoenix), which needless to say is suboptimal.
Signed-off-by: NJohan Hovold <jhovold@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix build error when CONFIG_MAGIC_SYSRQ is not enabled:

drivers/usb/serial/generic.c:566: error: implicit declaration of function 'handle_sysrq'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Add ZIO Motherboard USB serial interface driver.
Signed-off-by: NVijay Kumar B. <vijaykumar@zilogic.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb console code has had a long standing problem of not being able
to pass the baud rate from the kernel argument console=ttyUSB0,BAUD
down to the initial tty open, unless you were willing to settle for
9600 baud.

The solution is to directly use tty_init_termios() in
usb_console_setup() as this will preserve any changes to the initial
termios setting on future opens.

CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Replace all instances of using the console variable in struct
usb_serial_port with the struct tty_port version.

CC: Alan Cox <alan@linux.intel.com>
CC: Alan Stern <stern@rowland.harvard.edu>
CC: Oliver Neukum <oliver@neukum.org>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: linux-usb@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Signed-off-by: NJason Wessel <jason.wessel@windriver.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Fix printk format warning in usbserial/ti_usb:

drivers/usb/serial/ti_usb_3410_5052.c:1738: warning: format '%d' expects type 'int', but argument 5 has type 'size_t'
Signed-off-by: NRandy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This adds a device id for a Cinterion device.
Reported-by: NJohn Race <John.Race@roscom.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

PATCH TO EXTEND SUPPORT TO AC8710 WITH 0xFFFF Product ID.
Signed-off-by: NMahesh Kuruganti <maheshkuruganti@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I tried a magnetic stripe reader
(http://www.kimaldi.com/kimaldi_eng/productos/lectores_de_tarjetas/lectores_tarjeta_chip_y_dni/lector_hibrido_uniform_hcr_331)
and I see that it is interfaced with a PL2303. I wrote a patch to use
your driver which simply adds the product ID for the device and it
seems working fine.


From: Simone Contini <s.contini@oltrelinux.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Based on the information provided for by Paweł Drobek, add
a second vendor ID and the correct product ID for ZTE MF 330.
Reported-by: NPaweł Drobek <pawel.drobek@gmail.com>
Signed-off: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

I read a rumor that the AdLink ND6530 USB RS232, RS422 and RS485
isolated adapter is actually a PL2303 based usb serial adapter. I
tried it out, and as far as I can tell it works.
Signed-off-by: NManuel Jander <manuel.jander@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NWilliam Lightning <kassah@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

These phones also have the familiar ttyACM0/ttyUSB0 schizophrenia when
placed into "Dial-up Networking" mode after connecting a USB cable.
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>