This patch adds tracking of L2CAP connection oriented channel local and
remote credits to struct l2cap_chan and ensures that connect requests
and responses contain the right values.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The LE connection oriented channels have their own mode with its own
data transfer rules. In order to implement this properly we need to
distinguish L2CAP channels operating in this mode from other modes.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch makes the error handling and return logic of l2cap_le_sig_cmd
consistent with its BR/EDR counterpart.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The normal L2CAP Disconnect request and response are also used for LE
connection oriented channels. Therefore, we can simply use the existing
handler functions for terminating LE based L2CAP channels.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Sending of the L2CAP Disconnect request should also be performed for LE
based channels. The proper thing to do is therefore to look at whether
there's a PSM specified for the channel instead of looking at the link
type.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the necessary boiler plate code to handle receiving
L2CAP connect requests over LE and respond to them with a proper connect
response.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We'll need to have a separate code path for LE based connection
rejection so it's cleaner to move out the response construction code
into its own function (and later a second one for LE).
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This function is needed both by the smp_conn_security function as well
as upcoming code to check for the security requirements when receiving
an L2CAP connect request over LE.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the necessary code to send an LE L2CAP Connect Request
and handle its response when user space has provided us with an LE
socket with a PSM instead of a fixed CID.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds the necessary defines and structs for LE connection
oriented channels.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Once connection oriented L2CAP channels over LE are supported they will
need a completely separate handling from BR/EDR channels.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The LE signaling PDU length is already calculated in the
l2cap_le_sig_channel function so we can just pass the value to the
various handler functions to avoid unnecessary recalculations (byte
order conversions). Right now the only user is the connection parameter
update procedure, but as new LE signaling operations become available
(for connection oriented channels) they will also be able to make use of
the value.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

With connection oriented L2CAP channels some code paths will be shared
with BR/EDR links. It is therefore necessary to allow the
l2cap_chan_check_security function to be usable also for LE links in
addition to BR/EDR ones. This means that smp_conn_security() needs to be
called instead of hci_conn_security() in the case of an LE link.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Once connection oriented L2CAP channels become possible for LE we need
to be able to specify the link type we're interested in when looking up
L2CAP channels. Therefore, add a link_type parameter to the
l2cap_global_chan_by_psm() function which gets compared to the address
type associated with each l2cap_chan.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Along with the L2CAP Connection Oriented Channels features it is now
allowed to use both custom fixed CIDs as well as PSM based (connection
oriented connections). Since the support for this (with the subsequent
patches) is still on an experimental stage, add a module parameter to
enable it.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch is just a trivial coding style fix to remove unnecessary
braces from a one-line if-statement.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The AES cipher is used in ECB mode by SMP and therefore doesn't use an
IV (crypto_blkcipher_ivsize returns 0) so the code trying to set the IV
was never getting called. Simply remove this code to avoid anyone from
thinking it actually makes some difference.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This function was always just making a single get_random_bytes() call
and always returning the value 0. It's simpler to just call
get_random_bytes() directly where needed.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch enables autosuspend for Intel Bluetooth device.

After btusb is loaded for Intel Bluetooth device, the power/control
attribute contains "on" value by default which disables the autosuspend.
Based on the USB PM document(Documentation/usb/power-management.txt),
kernel disabled the autosuspend for all devices other than hub by default.

"The USB specification states that all USB devices must support power
management.  Nevertheless, the sad fact is that many devices do not
support it very well.  You can suspend them all right, but when you
try to resume them they disconnect themselves from the USB bus or
they stop working entirely.  This seems to be especially prevalent
among printers and scanners, but plenty of other types of device have
the same deficiency.

For this reason, by default the kernel disables autosuspend (the
power/control attribute is initialized to "on") for all devices other
than hubs.  Hubs, at least, appear to be reasonably well-behaved in
this regard."

This document also described how the driver can enables the autosuspend
by using an USB api.

"Drivers can enable autosuspend for their devices by calling

	usb_enable_autosuspend(struct usb_device *udev);

in their probe() routine, if they know that the device is capable of
suspending and resuming correctly.  This is exactly equivalent to
writing "auto" to the device's power/control attribute."

For Intel Bluetooth device, the autosuspend needs to be enabled so the
device can transit to LPM(Low Power Mode) and ULPM(Ultra LPM) states after
receiving suspend message from the host.
Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds support for new Intel Bluetooth device.

T:  Bus=02 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  4 Spd=12   MxCh= 0
D:  Ver= 2.01 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=8087 ProdID=0a2a Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  64 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: NTedd Ho-Jeong An <tedd.an@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

hci_disconn_complete_evt() logic is more complicated than what it
should be, making it hard to follow and add new features.

So this patch does some code refactoring by handling the error cases
in the beginning of the function and by moving the main flow into the
first level of function scope. No change is done in the event handling
logic itself.

Besides organizing this messy code, this patch makes easier to add
code for handling LE auto connection (which will be added in a further
patch).
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

According to b644ba33 (patch that introduced HCI_CONN_MGMT_CONNECTED
flag), the HCI_CONN_MGMT_CONNECTED flag tracks when mgmt has been
notified about the connection.

That being said, there is no point in calling mgmt_disconnect_failed()
conditionally based on this flag. mgmt_disconnect_failed() removes
pending MGMT_OP_DISCONNECT commands, it doesn't matter if that
connection was notified or not.

Moreover, if the Disconnection Complete event has status then we have
nothing else to do but call mgmt_disconnect_failed() and return.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

T:  Bus=02 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#=  9 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e05f Rev= 0.02
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Reported-by: NJoshua Richenhagen <richenhagen@gmail.com>
Signed-off-by: NSujith Manoharan <sujith@msujith.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=04ca ProdID=300b Rev= 0.01
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
Reported-by: NFace <falazemi@gmail.com>
Signed-off-by: NSujith Manoharan <sujith@msujith.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The send parameter has only been used for determining whether to send a
Pairing Failed PDU or not. However, the function can equally well use
the already existing reason parameter to make this choice and send the
PDU whenever a non-zero value was passed.
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

We can safely remove the link type check from hci_disconn_complete_
evt() since this check in not required for mgmt_disconnect_failed()
and mgmt_device_disconnected() does it internally.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

This patch adds an extra check in mgmt_device_disconnected() so we only
send the "Device Disconnected" event if it is ACL_LINK or LE_LINK link
type.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Check the address and address type in mgmt_disconnect_failed() otherwise
we may wrongly fail the MGMT_OP_DISCONNECT command.
Signed-off-by: NAndre Guedes <andre.guedes@openbossa.org>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The device tree property can define the cal-data in proper order.
There is no need to swap the bytes in driver.
Also remove the redundant cal-data memory copy after removing the
byte swapping.

Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NHyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Some ARM versions of Chromebook need to download a new calibration
data from host driver to firmware. They do have EEPROM but still
need a piece of new calibration data in test mode.

The cal-data is platform dependent. It's simpler and more feasible
to use device tree based cal-data instead of configuration file
based cal-data.

This patch remove configuration file based cal-data downloading
and replace it using cal-data from device tree.

When CONFIG_OF is not selected, or the specific property is not
present in the device tree, the calibration downloading will not
happen.

Cc: Mike Frysinger <vapier@chromium.org>
Cc: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NHyuckjoo Lee <hyuckjoo.lee@samsung.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

Replace ogf/ocf and its packing with 16-bit opcodes.
Signed-off-by: NBing Zhao <bzhao@marvell.com>
Signed-off-by: NAmitkumar Karwar <akarwar@marvell.com>
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>

The list of supported commands of a controller can not change during
its lifetime. So store the list just once during the setup procedure
and not every time the HCI command is executed.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The complete list of local features are available through debugfs and
so there is no need to add a debug print here.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

The default own address type is currently set at every power on of
a controller. This overwrites the value set via debugfs. To avoid
this issue, set the default own address type only during controller
setup.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

There is an old Panasonic module with a Zeevo chip in there that is
not really operating according to Bluetooth core specification when
it comes to setting the IAC LAP for limited discoverable mode.

For reference, this is the vendor information about this module:

  < HCI Command: Read Local Version Information (0x04|0x0001) plen 0
  > HCI Event: Command Complete (0x0e) plen 12
        Read Local Version Information (0x04|0x0001) ncmd 1
          Status: Success (0x00)
          HCI version: Bluetooth 1.2 (0x02) - Revision 196 (0x00c4)
          LMP version: Bluetooth 1.2 (0x02) - Subversion 61 (0x003d)
          Manufacturer: Zeevo, Inc. (18)

The module reports only the support for one IAC at a time. And that
is totally acceptable according to the Bluetooth core specification
since the minimum supported IAC is only one.

  < HCI Command: Read Number of Supported IAC (0x03|0x0038) plen 0
  > HCI Event: Command Complete (0x0e) plen 5
        Read Number of Supported IAC (0x03|0x0038) ncmd 1
          Status: Success (0x00)
          Number of IAC: 1

The problem arises when trying to program two IAC into the module
on a controller that only supports one.

  < HCI Command: Write Current IAC LAP (0x03|0x003a) plen 7
          Number of IAC: 2
          Access code: 0x9e8b00 (Limited Inquiry)
          Access code: 0x9e8b33 (General Inquiry)
  > HCI Event: Command Status (0x0f) plen 4
        Write Current IAC LAP (0x03|0x003a) ncmd 1
          Status: Unknown HCI Command (0x01)

While this looks strange, but according to the Bluetooth core
specification it is a legal operation. The controller has to
ignore the other values and only program as many as it supports.

  This command shall clear any existing IACs and stores Num_Current_IAC
  and the IAC_LAPs in to the controller. If Num_Current_IAC is greater
  than Num_Support_IAC then only the first Num_Support_IAC shall be
  stored in the controller, and a Command Complete event with error
  code Success (0x00) shall be generated.

This specific controller has a bug here and just returns an error. So
in case the number of supported IAC is less than two and the limited
discoverable mode is requested, now only the LIAC is written to
the controller.

  < HCI Command: Write Current IAC LAP (0x03|0x003a) plen 4
          Number of IAC: 1
          Access code: 0x9e8b00 (Limited Inquiry)
  > HCI Event: Command Complete (0x0e) plen 4
        Write Current IAC LAP (0x03|0x003a) ncmd 1
          Status: Success (0x00)

All other controllers that only support one IAC seem to handle this
perfectly fine, but this fix will only write the LIAC for these
controllers as well.
Signed-off-by: NMarcel Holtmann <marcel@holtmann.org>
Signed-off-by: NJohan Hedberg <johan.hedberg@intel.com>

Adding the debugfs file <debugfs_mnt>/brcmfmac/<devid>/chipinfo
which contains the chip number and revision.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The dhd.h file contained a number of definitions that are
related to events received from the firmware. Those are
processed and dispatched in the driver by fweh. Hence the
definitions are moved to its include file.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Removing WLC_PHY_TYPE and some BRCMF_E_.* definitions as these
are not used in the driver sources.
Reviewed-by: NHante Meuleman <meuleman@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The BCDC protocol layer is using a mix of naming of CDC, BDC and
BCDC. Use the name BCDC consistenly over all functions, defines
and variables. This patch does not change code functionality.
Reviewed-by: NArend Van Spriel <arend@broadcom.com>
Reviewed-by: NPieter-Paul Giesberts <pieterpg@broadcom.com>
Signed-off-by: NHante Meuleman <meuleman@broadcom.com>
Signed-off-by: NArend van Spriel <arend@broadcom.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>