Some firmware commands can under some circumstances take more than 2
seconds to complete.  This patch bumps the timeout up to 10 seconds,
and prints a message whenever a command takes more than 2 seconds.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

On 8366, bit 6 in the rx descriptor rate field indicates whether the
packet was received on a 20MHz or 40MHz channel, and is not part of
the MCS index.  Handle this properly, which then prevents hitting the
WARN_ON and being dropped in ieee80211_rx().
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When inserting a DMA header into a packet for transmission,
mwl8k_add_dma_header() would blindly zero the addr4 field, which
is not a good idea if the packet being transmitted is actually a
4-address packet.

Also, if the transmitted packet was a 4-address with QoS packet,
the memmove() to do the needed header reshuffling would inadvertently
overwrite the first two bytes of the packet payload with the QoS field.

This fixes both of these issues.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Packets exchanged between the mwl8k driver and the firmware always
have a 4-address header without QoS field.  For QoS packets, the QoS
field is passed to/from the firmware via the tx/rx descriptors.

We were handling this correctly on transmit, but not on receive -- if
a QoS packet was received, we would leave garbage in the QoS field in
the packet passed up to the stack, which is Bad(tm).

Also, if the packet received on the air was a 4-address without QoS
packet, we would forget to skb_pull the 2-byte DMA length prefix off.

This patch adds an argument to the ->rxd_process() receive descriptor
operation to retrieve the QoS field from the receive descriptor, and
extends mwl8k_remove_dma_header() to insert this field back into the
packet if the packet received is a QoS packet.  It also fixes
mwl8k_remove_dma_header() to strip off the length prefix in all cases.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There exist 12 802.11b/g rates, but mwl8k supports two additional
(non-standard) rates, and includes those rates in rate bitmasks and
in its internal rate table that hardware rate indices index.

Commit "mwl8k: report rate and other information for received frames"
added one of the nonstandard rates to the mwl8k_rates table to make
the OFDM rates in the table line up with the rate indices that are
reported in the receive descriptor (so that we can just simply copy
the receive descriptor rate index into ieee80211_rx_status::rate_idx)
and bumped MWL8K_IEEE_LEGACY_DATA_RATES from 12 to 13, but this
screwed up the UPDATE_STADB command struct layout, as it also uses
that define, for its legacy_rates array.

To avoid having to convert rate indices and legacy rate bitmaps (e.g.
ieee80211_bss_conf::basic_rates) between the 12-rate mac80211 format
and the 14-rate mwl8k format, we'll report all 14 rates in our wiphy's
band, but filter out the nonstandard ones e.g. in the case of the
UPDATE_STADB command which only accepts 12 rates.

In the commands that accept 14 rates (SET_AID, SET_RATE), replace the
use of the MWL8K_RATE_INDEX_MAX_ARRAY define in the command struct by
the constant 14, to make it clearer that these commands accept 14 rates.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The MCS bitmaps in the SET_RATE command structure were of the wrong
size, due to use of the wrong define for the array length.  Just
hardcode the lengths as 16, and do the same for the MCS bitmaps in
other command structures.
Signed-off-by: NLennert Buytenhek <buytenh@marvell.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Not only ps_sdata but also IEEE80211_CONF_PS is to be considered
before restoring PS in scan_ps_disable(). For instance, when ps_sdata
is set but CONF_PS is not set just because the dynamic timer is still
running, a sw scan leads to setting of CONF_PS in scan_ps_disable
instead of restarting the dynamic PS timer.
Also for the above case, a null data frame is to be sent after
returning to operating channel which was not happening with the
current implementation. This patch fixes this too.
Signed-off-by: NVivek Natarajan <vnatarajan@atheros.com>
Reviewed-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

hwsim testing has revealed that when the MLME
recalculates the idle state of the device, it
sometimes does so before sending the final
deauthentication or disassociation frame. This
patch changes the place where the idle state
is recalculated, but of course driver transmit
is typically asynchronous while configuration
is expected to be synchronous, so it doesn't
fix all possible cases yet.
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The bssid can be zero when null data template is set in wl1251_op_config().
It's enough, and especially safe, to set it once after association.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

bssid needs to be copied first in wl1251_op_bss_info_changed(), otherwise
templates will have incorrect bssid and power save will not work
correctly.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

There was a warning from wl1251_op_bss_info_changed():

wl1251: WARNING Set ctsprotect failed 0

It was printed always, it's completely false and can be removed.
Signed-off-by: NKalle Valo <kalle.valo@nokia.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

CC [M]  drivers/net/wireless/iwlwifi/iwl-tx.o
drivers/net/wireless/iwlwifi/iwl-tx.c: In function ‘iwl_tx_agg_stop’:
drivers/net/wireless/iwlwifi/iwl-tx.c:1356: warning: passing argument 1 of ‘ieee80211_stop_tx_ba_cb_irqsafe’ from incompatible pointer type
include/net/mac80211.h:2128: note: expected ‘struct ieee80211_vif *’ but argument is of type ‘struct ieee80211_hw *’
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Conflicts:
	drivers/net/pcmcia/fmvj18x_cs.c
	drivers/net/pcmcia/nmclan_cs.c
	drivers/net/pcmcia/xirc2ps_cs.c
	drivers/net/wireless/ray_cs.c

Merge branch 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (40 commits)
  tracing: Separate raw syscall from syscall tracer
  ring-buffer-benchmark: Add parameters to set produce/consumer priorities
  tracing, function tracer: Clean up strstrip() usage
  ring-buffer benchmark: Run producer/consumer threads at nice +19
  tracing: Remove the stale include/trace/power.h
  tracing: Only print objcopy version warning once from recordmcount
  tracing: Prevent build warning: 'ftrace_graph_buf' defined but not used
  ring-buffer: Move access to commit_page up into function used
  tracing: do not disable interrupts for trace_clock_local
  ring-buffer: Add multiple iterations between benchmark timestamps
  kprobes: Sanitize struct kretprobe_instance allocations
  tracing: Fix to use __always_unused attribute
  compiler: Introduce __always_unused
  tracing: Exit with error if a weak function is used in recordmcount.pl
  tracing: Move conditional into update_funcs() in recordmcount.pl
  tracing: Add regex for weak functions in recordmcount.pl
  tracing: Move mcount section search to front of loop in recordmcount.pl
  tracing: Fix objcopy revision check in recordmcount.pl
  tracing: Check absolute path of input file in recordmcount.pl
  tracing: Correct the check for number of arguments in recordmcount.pl
  ...

Merge branch 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'tracing-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  tracing: Fix trace_marker output
  tracing: Fix event format export
  tracing: Fix return value of tracing_stats_read()

Merge branch 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'irq-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  genirq: Fix spurious irq seqfile conversion
  genirq: switch /proc/irq/*/spurious to seq_file
  irq: Do not attempt to create subdirectories if /proc/irq/<irq> failed
  irq: Remove unused debug_poll_all_shared_irqs()
  irq: Fix docbook comments
  irq: trivial: Fix typo in comment for #endif

Merge branch 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-softlockup-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  softlockup: Fix hung_task_check_count sysctl

Merge branch 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-signal-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  signal: Print warning message when dropping signals
  signal: Fix alternate signal stack check

Merge branch 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (31 commits)
  rcu: Make RCU's CPU-stall detector be default
  rcu: Add expedited grace-period support for preemptible RCU
  rcu: Enable fourth level of TREE_RCU hierarchy
  rcu: Rename "quiet" functions
  rcu: Re-arrange code to reduce #ifdef pain
  rcu: Eliminate unneeded function wrapping
  rcu: Fix grace-period-stall bug on large systems with CPU hotplug
  rcu: Eliminate __rcu_pending() false positives
  rcu: Further cleanups of use of lastcomp
  rcu: Simplify association of forced quiescent states with grace periods
  rcu: Accelerate callback processing on CPUs not detecting GP end
  rcu: Mark init-time-only rcu_bootup_announce() as __init
  rcu: Simplify association of quiescent states with grace periods
  rcu: Rename dynticks_completed to completed_fqs
  rcu: Enable synchronize_sched_expedited() fastpath
  rcu: Remove inline from forward-referenced functions
  rcu: Fix note_new_gpnum() uses of ->gpnum
  rcu: Fix synchronization for rcu_process_gp_end() uses of ->completed counter
  rcu: Prepare for synchronization fixes: clean up for non-NO_HZ handling of ->completed counter
  rcu: Cleanup: balance rcu_irq_enter()/rcu_irq_exit() calls
  ...

Merge branch 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-printk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  ratelimit: Make suppressed output messages more useful
  printk: Remove ratelimit.h from kernel.h
  ratelimit: Fix/allow use in atomic contexts
  ratelimit: Use per ratelimit context locking

Merge branch 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-locking-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  mutex: Fix missing conditions to build mutex_spin_on_owner()
  mutex: Better control mutex adaptive spinning config
  locking, task_struct: Reduce size on TRACE_IRQFLAGS and 64bit
  locking: Use __[SPIN|RW]_LOCK_UNLOCKED in [spin|rw]_lock_init()
  locking: Remove unused prototype
  locking: Reduce ifdefs in kernel/spinlock.c
  locking: Make inlining decision Kconfig based

Merge branch 'core-ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-ipi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  generic-ipi: Add smp_call_function_any()
  generic-ipi: Fix misleading smp_call_function*() description

Merge branch 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
  x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
  x86/amd-iommu: Remove amd_iommu_pd_table
  x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
  x86/amd-iommu: Cleanup DTE flushing code
  x86/amd-iommu: Introduce iommu_flush_device() function
  x86/amd-iommu: Cleanup attach/detach_device code
  x86/amd-iommu: Keep devices per domain in a list
  x86/amd-iommu: Add device bind reference counting
  x86/amd-iommu: Use dev->arch->iommu to store iommu related information
  x86/amd-iommu: Remove support for domain sharing
  x86/amd-iommu: Rearrange dma_ops related functions
  x86/amd-iommu: Move some pte allocation functions in the right section
  x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
  x86/amd-iommu: Use get_device_id and check_device where appropriate
  x86/amd-iommu: Move find_protection_domain to helper functions
  x86/amd-iommu: Simplify get_device_resources()
  x86/amd-iommu: Let domain_for_device handle aliases
  x86/amd-iommu: Remove iommu specific handling from dma_ops path
  x86/amd-iommu: Remove iommu parameter from __(un)map_single
  x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-nmw: (31 commits)
  GFS2: Fix glock refcount issues
  writeback: remove unused nonblocking and congestion checks (gfs2)
  GFS2: drop rindex glock to refresh rindex list
  GFS2: Tag all metadata with jid
  GFS2: Locking order fix in gfs2_check_blk_state
  GFS2: Remove dirent_first() function
  GFS2: Display nobarrier option in /proc/mounts
  GFS2: add barrier/nobarrier mount options
  GFS2: remove division from new statfs code
  GFS2: Improve statfs and quota usability
  GFS2: Use dquot_send_warning()
  VFS: Export dquot_send_warning
  GFS2: Add set_xquota support
  GFS2: Add get_xquota support
  GFS2: Clean up gfs2_adjust_quota() and do_glock()
  GFS2: Remove constant argument from qd_get()
  GFS2: Remove constant argument from qdsb_get()
  GFS2: Add proper error reporting to quota sync via sysfs
  GFS2: Add get_xstate quota function
  GFS2: Remove obsolete code in quota.c
  ...

* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6: (30 commits)
  TOMOYO: Add recursive directory matching operator support.
  remove CONFIG_SECURITY_FILE_CAPABILITIES compile option
  SELinux: print denials for buggy kernel with unknown perms
  Silence the existing API for capability version compatibility check.
  LSM: Move security_path_chmod()/security_path_chown() to after mutex_lock().
  SELinux: header generation may hit infinite loop
  selinux: Fix warnings
  security: report the module name to security_module_request
  Config option to set a default LSM
  sysctl: require CAP_SYS_RAWIO to set mmap_min_addr
  tpm: autoload tpm_tis based on system PnP IDs
  tpm_tis: TPM_STS_DATA_EXPECT workaround
  define convenient securebits masks for prctl users (v2)
  tpm: fix header for modular build
  tomoyo: improve hash bucket dispersion
  tpm add default function definitions
  LSM: imbed ima calls in the security hooks
  SELinux: add .gitignore files for dynamic classes
  security: remove root_plug
  SELinux: fix locking issue introduced with c6d3aaa4
  ...

* git://git.kernel.org/pub/scm/linux/kernel/git/brodo/pcmcia-2.6: (50 commits)
  pcmcia: rework the irq_req_t typedef
  pcmcia: remove deprecated handle_to_dev() macro
  pcmcia: pcmcia_request_window() doesn't need a pointer to a pointer
  pcmcia: remove unused "window_t" typedef
  pcmcia: move some window-related code to pcmcia_ioctl.c
  pcmcia: Change window_handle_t logic to unsigned long
  pcmcia: Pass struct pcmcia_socket to pcmcia_get_mem_page()
  pcmcia: Pass struct pcmcia_device to pcmcia_map_mem_page()
  pcmcia: Pass struct pcmcia_device to pcmcia_release_window()
  drivers/pcmcia: remove unnecessary kzalloc
  pcmcia: correct handling for Zoomed Video registers in topic.h
  pcmcia: fix printk formats
  pcmcia: autoload module pcmcia
  pcmcia/staging: update comedi drivers
  PCMCIA: stop duplicating pci_irq in soc_pcmcia_socket
  PCMCIA: ss: allow PCI IRQs > 255
  PCMCIA: soc_common: remove 'dev' member from soc_pcmcia_socket
  PCMCIA: soc_common: constify soc_pcmcia_socket ops member
  PCMCIA: sa1111: remove duplicated initializers
  PCMCIA: sa1111: wrap soc_pcmcia_socket to contain sa1111 specific data
  ...

Use the new unreachable() macro instead of for(;;);
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NHaavard Skinnemoen <haavard.skinnemoen@atmel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the new unreachable() macro instead of for(;;);
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NMartin Schwidefsky <schwidefsky@de.ibm.com>
CC: Heiko Carstens <heiko.carstens@de.ibm.com>
CC: linux390@de.ibm.com
CC: linux-s390@vger.kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the new unreachable() macro instead of while(1);
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
CC: linux-mips@linux-mips.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Use the new unreachable() macro instead of for(;;);.  When
allyesconfig is built with a GCC-4.5 snapshot on i686 the size of the
text segment is reduced by 3987 bytes (from 6827019 to 6823032).
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: N"H. Peter Anvin" <hpa@zytor.com>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Ingo Molnar <mingo@redhat.com>
CC: x86@kernel.org
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Starting with version 4.5, GCC has a new built-in function
__builtin_unreachable() that can be used in places like the kernel's
BUG() where inline assembly is used to transfer control flow.  This
eliminated the need for an endless loop in these places.

The patch adds a new macro 'unreachable()' that will expand to either
__builtin_unreachable() or an endless loop depending on the compiler
version.

Change from v1: Simplify unreachable() for non-GCC 4.5 case.
Signed-off-by: NDavid Daney <ddaney@caviumnetworks.com>
Acked-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

My patch "mac80211: correctly place aMPDU RX reorder code"
uses an skb queue for MPDUs that were released from the
buffer. I intentially didn't initialise and use the skb
queue's spinlock, but in this place forgot that the code
variant that doesn't touch the spinlock is needed.

Thanks to Christian Lamparter for quickly spotting the
bug in the backtrace Reinette reported.
Reported-by: NReinette Chatre <reinette.chatre@intel.com>
Bug-identified-by: NChristian Lamparter <chunkeey@googlemail.com>
Tested-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohannes Berg <johannes@sipsolutions.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When debugging the wifi firmware, we need to disable the wimax core to gain
some memory space. The default value will keep the wimax core enabled.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Wifi and wimax coexistence mode is set by wifi at boot time. There can be
several modes, defined by priority tables. User space components can decide
which one to select by writing to /sys/module/iwmc3200wifi/parameters/wiwi
with this patch, before bringing the interface up.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

When sending the wiwi coexistence priority table, we should not tell the LMAC
that we want a response.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This update follows the firmware engineers recommendations.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The driver version number is a remnant from when there was an out-of-tree
iwlwifi driver. Now that the driver forms part of kernel source we do not
need a separate driver version. Instead, we now use the kernel version as
driver version. We maintain the previous tags used to indicate which
components the driver has been compiled with.
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Acked-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

error_event_table_ptr is only set upon receipt of REPLY_ALIVE. Until
then both event log and error log will fail. Add information to indicate
which uCode encounter the failure case.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

In the process of improving uCode event logging capability, the new
implementation was introduced without removing the existing
implementation. The event log will be dumped to dmesg twice.
Remove the old implementation to only log the event once upon sys
assert or request by user.
Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: NReinette Chatre <reinette.chatre@intel.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>