The variable 'extra_size' is set but unused in
atl1c_configure_tx().  Just kill it off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable 'tx_ring' is set but unused in
atl1e_init_ring_resources().  Just kill it off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable 'tpc' is set but unused in atl1_intr_tx().
Just kill it off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable 'vlan_dev' is set but unused in
bond_send_gratuitous_arp().  Just kill it off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable 'eth' is set but unused in lec_handle_bridge().  Also,
the variable 'priv' is set but unused in lane_module_cleanup().

Just kill them off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable 's' is set but unused in ax25_protocol_release().
Just kill it off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

#if 0'd out code for IP handling in aun_data_available() has
been commented out since the beginning, which makes the variable
"ip" set but not used.

Kill it off as well as the stub code.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"next" in dn_rebuild_zone() is set but not actually used,
kill it off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

"iph" in pktgen_output_ipsec() is set but never actually
used.  Kill it off.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is just a readback to entire completion of a register
write, keep the readback but kill the unused variable.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two cases here:

1) idt77252_rx_raw() really does not make any use of the
   extracted PTI field of the atm header.

2) idt77252_collect_stat() only uses the register values
   in code which has been compiled out by a "NOTDEF" cpp
   test for more than 10 years.  Just kill this NOTDEF
   code entirely, but keep the register reads in case
   they have side effects.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GCC complains in these queue index operations because we
perform operations of the form:

	x = some_operation(++x);

which is undefined.  Replace with:

	x = some_operation(x + 1);

which is well defined and provides the intended operation.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The variable eni_dev is initialized but never subsequently used in
these two functions.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Note: I bet that gfar_set_features() don't really need a full reset.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This also fixes a race around np->txrxctl_bits while changing RXCSUM offload.
Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMichał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Inline a small static function that's only ever called from one place.
Signed-off-by: NRob Landley <rlandley@parallels.com>
Reviewed-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[ipv6] Add support for RTA_PREFSRC

This patch allows a user to select the preferred source address
for a specific IPv6-Route. It can be set via a netlink message
setting RTA_PREFSRC to a valid IPv6 address which must be
up on the device the route will be bound to.
Signed-off-by: NDaniel Walter <dwalter@barracuda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

[ipv6] Ignore looped-back NAs while in Duplicate Address Detection

If we send an unsolicited NA shortly after bringing up an
IPv6 address, the duplicate address detection algorithm
fails and the ip stays in tentative mode forever.
This is due a missing check if the NA is looped-back to us.
Signed-off-by: NDaniel Walter <dwalter@barracuda.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

My changes in commit 4d42d417 were
written some time before the introduction of FLAG_POINTTOPOINT, so
didn't include that flag in the new driver_info.  Change the new
driver_info to be consistent.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This updates the bonding driver to support v2.6.27-rc3 enhancements
(b11f8d8c aka. "ethtool: Expand ethtool_cmd.speed to 32 bits") which
allow to encode the Mbps link speed on 32-bits (Max 4 Pbps) instead of
16 (Max 65536 Mbps).

This patch also attempts to compact struct slave by reordering its
fields.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The __get_link_speed() function returns a u16 value which was stored
in a u32 local variable. This patch uses the return value directly,
thus fixing that minor type consistency.

The 'duplex' field in struct slave being encoded on 8 bits, to be more
consistent we use a u8 integer (instead of u16) whenever we copy it to
local variables.
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This gets rid of minor sparse complaints:
drivers/net/bonding/bond_main.c:4361:4: warning: do-while statement is not a compound statement
drivers/net/bonding/bond_main.c:243:12: warning: symbol 'bond_mode_name' was not declared. Should it be static?
Signed-off-by: NDavid Decotigny <decot@google.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The struct nic_operations is just function pointers and should be
declared const for added security.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The phy, mac, and board information structures should be const.
Since tables contain function pointer this improves security
(at least theoretically).

Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This gets rid of the last spinlock in the Phonet stack proper.
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When physical identification of an adapter is done by toggling the
mechanism on and off through software utilizing the set_phys_id operation,
it is done with a fixed duration for both on and off states.  Some drivers
may want to set a custom duration for the on/off intervals.  This patch
changes the API so the return code from the driver's entry point when it
is called with ETHTOOL_ID_ACTIVE can specify the frequency at which to
cycle the on/off states, and updates the drivers that have already been
converted to use the new set_phys_id and use the synchronous method for
identifying an adapter.

The physical identification frequency set in the updated drivers is based
on how it was done prior to the introduction of set_phys_id.

Compile tested only.  Also fixes a compiler warning in sfc.

v2: drivers do not return -EINVAL for ETHOOL_ID_ACTIVE
v3: fold patchset into single patch and cleanup per Ben's feedback
Signed-off-by: NBruce Allan <bruce.w.allan@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Eilon Greenstein <eilong@broadcom.com>
Cc: Divy Le Ray <divy@chelsio.com>
Cc: Don Fry <pcnet32@frontier.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steve Hodgson <shodgson@solarflare.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Matt Carlson <mcarlson@broadcom.com>
Acked-by: NJon Mason <jdmason@kudzu.us>
Acked-by: NBen Hutchings <bhutchings@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

fib_select_default() is a complete NOP, and completely pointless
to invoke, when we have no more than 1 default route installed.

And this is far and away the common case.

So remember how many prefixlen==0 routes we have in the routing
table, and elide the call when we have no more than one of those.

This cuts output route creation time by 157 cycles on Niagara2+.

In order to add the new int to fib_table, we have to correct the type
of ->tb_data[] to unsigned long, otherwise the private area will be
unaligned on 64-bit systems.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
Reviewed-by: NEric Dumazet <eric.dumazet@gmail.com>

Nobody alive seems to recall when they last were useful.
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

DCB enabled X540 devices are not responding to pause frames
due to a missing register set that was added for these
devices that did not exist in other devices.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

The X540 device has a smaller packet buffer but the DCB configuration
never took this into account. Under stress this can result in the DMA
engine hanging and TX Unit hang occurring to reset the device. This
patch reworks the packet buffer allocation routine used for DCB on
82599 and X540 devices to account for RX packet buffer sizes.

This fixes the immediate hang. We should consolidate the various
hardware specific routines for configuring features into a single
routine. This will make it much harder to miss feature cases like
this.
Signed-off-by: NJohn Fastabend <john.r.fastabend@intel.com>
Tested-by: NRoss Brattain <ross.b.brattain@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

x540 has the same device capability word in the EEPROM as 82599.
This patch renames ixgbe_get_device_caps_82599 to
ixgbe_get_device_caps_generic, moves it to ixgbe_common.h and
sets up the function pointer for x540.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

100H is not supported on this HW, but the bit is set on the PHY.
This can result in link at 100F when advertising only 1000F.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Add new device ID supported by ixgbe.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

HW can upload EEPROM content from flash while
in a middle of checksum calculation. Take NVM ownership for the whole
process of checksum update.

Call ixgbe_read_eerd_generic() and ixgbe_write_eewr_generic() directly to
avoid double take of semaphores which leads to long loading times.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Since msleep might not sleep for the desired amount when less
than 20ms use usleep_range.
Signed-off-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NStephen Ko <stephen.s.ko@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Disable KR to KX4/KX downshift on 82599 backplane devices when
LESM (Link Establishment State Machine) is enabled in FW. Those
features cannot co-exist as they both manipulate the same registers.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Acked-by: NDon Skidmore <donald.c.skidmore@intel.com>
Tested-by: NPhillip Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

Relaxed ordering can lead to issues with some chipsets.

This patch makes sure that it is disabled by default and
not only when DCA is on.
Signed-off-by: NEmil Tantilov <emil.s.tantilov@intel.com>
Tested-by: NEvan Swanson <evan.swanson@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>