This patch moves the data allocated using dma_alloc_coherent to the
corresponding managed interface and does away with the calls to free the
allocated memory in the probe and remove functions.
Signed-off-by: NHimangi Saraogi <himangi774@gmail.com>
Acked-by: NJulia Lawall <julia.lawall@lip6.fr>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

drivers/net/can/spi/mcp251x.c:953:7-27: ERROR: Threaded IRQ with no primary handler requested without IRQF_ONESHOT

 Make sure threaded IRQs without a primary handler are always request with
 IRQF_ONESHOT

Generated by: scripts/coccinelle/misc/irqf_oneshot.cocci

CC: Stefano Babic <sbabic@denx.de>
CC: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Create a directory for all CAN drivers using SPI and move mcp251x driver there.
Signed-off-by: NStefano Babic <sbabic@denx.de>
Acked-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds check for mcp251x_hw_reset() result on startup and
removes unnecessary checking for CANSTAT register since this value
is being checked in mcp251x_hw_reset().
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Tested-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

The MCP251x utilizes an oscillator startup timer (OST), which holds the
chip in reset, to insure that the oscillator has stabilized before the
internal state machine begins to operate. The OST maintains reset for
the first 128 OSC clock cycles after power up or reset.
So, this patch removes unnecessary loops and reduce delay for power on
and reset to the safe value.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Tested-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch moves setup of SPI bus a bit earlier and adds check for spi_setup()
result to be sure SPI bus is communicating with the device properly.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Tested-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

If CONFIG_REGULATOR is not set, devm_regulator_get() returns NULL,
so use IS_ERR_OR_NULL() macro for checks.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

CAN interfaces only support MTU values of 16 (CAN 2.0) and 72 (CAN FD).
Setting the MTU to other values is pointless but it does not really hurt.
With the introduction of the CAN FD support in drivers/net/can a new
function to switch the MTU for CAN FD has been introduced.

This patch makes use of this can_change_mtu() function to check for correct
MTU settings also in legacy CAN (2.0) devices.
Signed-off-by: NOliver Hartkopp <socketcan@hartkopp.net>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch removes #ifdef CONFIG_PM_SLEEP to improve compile coverage.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch moves one diagnostic message used for debugging purposes
to dev_dbg() and removes one useless message.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch adds Device Tree support to the Microchip MCP251X driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Replace existing resource handling in the driver with managed
device resource, this ensures more consistent error values and
simplifies error paths.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Several files refer to an old address for the Free Software Foundation
in the file header comment.  Resolve by replacing the address with
the URL <http://www.gnu.org/licenses/> so that we do not have to keep
updating the header comments anytime the address changes.

CC: Wolfgang Grandegger <wg@grandegger.com>
CC: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Patch allow to use different mode settings for SPI (MODE3 for example)
and limit maximal speed according to IC datasheet.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Flags is not used by boards, so remove this field from the driver
platform_data.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch replaces power callbacks to the regulator API. To improve
the readability of the code, helper for the regulator enable/disable
was added.
Acked-by: NHaojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

SIMPLE_DEV_PM_OPS macro can handle !CONFIG_PM_SLEEP case nicely, so there is no
need to define PM_OPS for both CONFIG_PM_SLEEP and !CONFIG_PM_SLEEP cases.

Remove the unneeded definitions.

Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NFabio Estevam <fabio.estevam@freescale.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit:

    1c6c6952 genirq: Reject bogus threaded irq requests

threaded irqs must provide a primary handler or set the IRQF_ONESHOT flag.
Since the mcp251x driver doesn't make use of a primary handler set the
IRQF_ONESHOT flag.

Cc: linux-stable <stable@vger.kernel.org> # >= v3.5
Reported-by: NMylene Josserand <Mylene.Josserand@navocap.com>
Tested-by: NMylene Josserand <Mylene.Josserand@navocap.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use dev_pm_ops instead of the deprecated legacy suspend/resume callbacks.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

By using module_spi_driver we can eliminate a few lines of boilerplate code.
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

In ancient times it was necessary to manually initialize the bus field of an
spi_driver to spi_bus_type. These days this is done in spi_driver_register() so
we can drop the manual assignment.

The patch was generated using the following coccinelle semantic patch:
// <smpl>
@@
identifier _driver;
@@
struct spi_driver _driver = {
	.driver = {
-		.bus = &spi_bus_type,
	},
};
// </smpl>
Signed-off-by: NLars-Peter Clausen <lars@metafoo.de>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Add support for canbus activity led indicators on mcp251x devices by
calling appropriate can_led functions.

These are only enabled when CONFIG_CAN_LEDS is Y, becomes no-op
otherwise.

Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NFabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

CONFIG_HOTPLUG is going away as an option.  As result the __dev*
markings will be going away.

Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Signed-off-by: NBill Pemberton <wfp5p@virginia.edu>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: linux-can@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The MCP2515 has a silicon bug causing repeated frame transmission, see section
5 of MCP2515 Rev. B Silicon Errata Revision G (March 2007).

Basically, setting TXBnCTRL.TXREQ in either SPI mode (00 or 11) will eventually
cause the bug. The workaround proposed by Microchip is to use mode 00 and send
a RTS command on the SPI bus to initiate the transmission.

Cc: <stable@vger.kernel.org>
Signed-off-by: NBenoît Locher <Benoit.Locher@skf.com>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

This patch marks the bittiming_const pointer as in the struct can_pric as
"const". This allows us to mark the struct can_bittiming_const in the CAN
drivers as "const", too.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

Adding casts of objects to the same type is unnecessary
and confusing for a human reader.

For example, this cast:

        int y;
        int *p = (int *)&y;

I used the coccinelle script below to find and remove these
unnecessary casts.  I manually removed the conversions this
script produces of casts with __force, __iomem and __user.

@@
type T;
T *p;
@@

-       (T *)p
+       p
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cc: uclinux-dist-devel@blackfin.uclinux.org
Cc: Anant Gole <anantgole@ti.com>
Cc: Chris Elston <celston@katalix.com>
Cc: Sebastian Haas <haas@ems-wuensche.com>
Cc: Matthias Fuchs <matthias.fuchs@esd.eu>
Signed-off-by: NWolfgang Grandegger <wg@grandegger.com>
Acked-by: NSebastian Haas <dev@sebastianhaas.info>
Acked-by: NMike Frysinger <vapier@gentoo.org>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>

When an interrupt occurs, the INT pin is driven low by the
MCP251x controller (falling edge) but in some cases the INT
pin can be connected to the MPU through a transistor or level
translator which inverts this signal. In this case interrupt
should be configured in rising edge.

This patch adds support to pass the IRQ flags via
mcp251x_platform_data.
Signed-off-by: NEnric Balletbo i Serra <eballetbo@iseebcn.com>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>
Acked-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are two spellings in use for 'freeze' + 'able' - 'freezable' and
'freezeable'.  The former is the more prominent one.  The latter is
mostly used by workqueue and in a few other odd places.  Unify the
spelling to 'freezable'.
Signed-off-by: NTejun Heo <tj@kernel.org>
Reported-by: NAlan Stern <stern@rowland.harvard.edu>
Acked-by: N"Rafael J. Wysocki" <rjw@sisk.pl>
Acked-by: NGreg Kroah-Hartman <gregkh@suse.de>
Acked-by: NDmitry Torokhov <dtor@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Alex Dubov <oakad@yahoo.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Steven Whitehouse <swhiteho@redhat.com>

This patch sets the missing CAN_RTR_FLAG if a standard RTR frame is
received.
(For extended frames the CAN_RTR_FLAG was already set correctly.)
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function "mcp251x_error_skb" is used to generate error frames.
They are identified by the "CAN_ERR_FLAG" in can_id. The function
overwrites the can_id so that the frames show up as normal frames instead
of error frames.

This patch fixes the problem by or'ing the can_id instead of overwriting it.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Tested-by: NJargalan Nermunkh <jargalan.nermunkh@criticallink.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit d3cd1565 introduced a bug, the
interrupt handler would loop endlessly if the CANINTF_MERRF bit is set,
because it's not cleared.

This patch fixes the problem by masking out the CANINTF_MERRF and all other
non interesting bits.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

Since commit e446630c, i.e. v2.6.35-rc1,
the mcp251x chip model can be selected via the modalias member in the
struct spi_board_info. The driver stores the actual model in the
struct mcp251x_platform_data.

From the driver point of view the platform_data should be read only.
Since all in-tree users of the mcp251x have already been converted to
the modalias method, this patch moves the "model" member from the
struct mcp251x_platform_data to the driver's private data structure.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Marc Zyngier <maz@misterjones.org>

This patch introduces a variable "clear_intf" that hold the bits that
should be cleared. Only read-modify-write register if "clear_intf"
is set.
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

Use read-modify-write instead of a simple write to change the register
contents, to close existing the race window between the original manual
read and write.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>

This patch bases on work done earlier by David Jander.
Signed-off-by: NSascha Hauer <s.hauer@pengutronix.de>
Acked-by: NDavid Jander <david@protonic.nl>
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: NMarc Kleine-Budde <mkl@pengutronix.de>
Acked-by: NWolfgang Grandegger <wg@grandegger.com>