On SKL, GT frequency is programmed in units of 16.66 MHZ units compared
to 50 MHZ for older platforms. Also the time value specified for Up/Down EI &
Up/Down thresholds are expressed in units of 1.33 us, compared to 1.28
us for older platforms. So updated the gen9_enable_rps function as per that.

v2: Updated to use new macro GT_INTERVAL_FROM_US

v3: Removed the initial setup of certain registers, from gen9_enable_rps,
    which gets overridden later from gen6_set_rps (Damien)

v4: Removed the enabling of rps interrupts, from gen9_enable_rps.
    To be done from intel_gen6_powersave_work only, as done for other
    platforms also.
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

RP Interrupt Up/Down Frequency Limits register (A014) definition
has changed for SKL. Updated the gen6_rps_limits function as per that

v2: Renamed the function to intel_rps_limits (Chris)
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Prior to SKL, the time period programmed in Up/Down EI & Up/Down
threshold registers was in units of 1.28 micro seconds. But for
SKL, the units have changed (1.333 micro seconds).
Have generalized the implementation of gen6_set_rps_thresholds function,
by removing the hard coding done in it as per 1.28 micro seconds.

v2: Renamed the local variables & removed superfluous comments (Chris)
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On SKL, the frequency is programmed differently in RPNSWREQ (A008)
register (from bits 23 to 31, compared to bits 24 to 31). So updated
the gen6_set_rps function, as per this change.
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On SKL the frequency is specified in units of 16.66 MHZ, barring the
RP_STATE_CAP(0x5998) register, which still reports frequency in units
of 50 MHZ. So an extra conversion is required in gen6_init_rps_frequencies
function for SKL, to store the frequency values as per the actual hardware unit.

v2: Corrected the conversion from 50 to 16.66 MHZ (Ville)
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

On SKL, frequency is specified in units of 16.66 MHZ.
Updated the intel_gpu_freq() and intel_freq_opecode() functions
to do the conversion appropriately.
Signed-off-by: NAkash Goel <akash.goel@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Use the FW_WM() macro from the VLV wm code to polish up the wm
code for older gmch platforms.

Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Wrap the FW register value shift+mask operations into a macro to hide
the ugliness a bit. Also might avoid bugs due to typos.

Also rename all the primary/sprite plane low order bit masks to have the
_VLV suffix, so that we can use the FW_WM_VLV() macro instead of the
FW_WM() macro for them in a consistent manner. Cursor and all the high
order bits are left to use the FW_WM() macro as there's no real
confusion with them.

Cc: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Current ILK-style watermark code assumes the primary plane and cursor
plane are always enabled.  This assumption, along with the combination
of two independent commits that got merged at the same time, results in
a NULL dereference.  The offending commits are:

        commit fd2d61341bf39d1054256c07d6eddd624ebc4241
        Author: Matt Roper <matthew.d.roper@intel.com>
        Date:   Fri Feb 27 10:12:01 2015 -0800

            drm/i915: Use plane->state->fb in watermark code (v2)

and

        commit 0fda6568
        Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
        Date:   Fri Feb 27 15:12:35 2015 +0000

            drm/i915/skl: Update watermarks for Y tiling

The first commit causes us to use the FB from plane->state->fb rather
than the legacy plane->fb, which is updated a bit later in the process.

The second commit includes a change that now triggers watermark
reprogramming on primary plane enable/disable where we didn't have one
before (which wasn't really correct, but we had been getting lucky
because we always calculated as if the primary plane was on).

Together, these two commits cause the watermark calculation to
(properly) see plane->state->fb = NULL when we're in the process of
disabling the primary plane.  However the existing watermark code
assumes there's always a primary fb and tries to dereference it to find
out pixel format / bpp information.

The fix is to make ILK-style watermark calculation actually check the
true status of primary & cursor planes and adjust our watermark logic
accordingly.

v2: Update unchecked uses of state->fb for other platforms (pnv, skl,
    etc.).  Note that this is just a temporary fix.  Ultimately the
    useful information is going to be computed at check time and stored
    right in the state structures so that we don't have to figure this
    all out while we're supposed to be programming the watermarks.
    (caught by Tvrtko)

v3: Fix a couple copy/paste mistakes in SKL code. (Tvrtko)

v4: Only add FB checks for ILK/SKL codepaths.  Older platforms still use
    intel_crtc_active() and will shortcircuit out of watermark
    calculations before ever trying to dereference the primary plane's
    framebuffer.

Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Reported-by: NMichael Leuchtenburg <michael@slashhome.org>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89388Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

DDR DVFS introduces massive memory latencies which can't be handled by
the PND deadline stuff. Instead the watermarks will need to be
programmed to compensate for the latency and the deadlines will need to
be programmed to tight fixed values. That means DDR DVFS can only be
enabled if the display FIFOs are large enough, and that pretty much
means we have to manually repartition them to suit the needs of the
moment.

That's a lot of change, so in the meantime let's just disable DDR DVFS
to get the display(s) to be stable.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

CHV has a new knob in Punit to select between some memory power savings
modes PM2 and PM5. We can allow the deeper PM5 when maxfifo mode is
enabled, so let's do so in the hopes for moar power savings.

v2: Put the thing into a separate function to avoid churn later
v3: Don't break VLV
Reviewed-by: NVijay Purushothaman <vijay.a.purushothaman@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NArun R Murthy <arun.r.murthy@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Assuming the PND deadline mechanism works reasonably we should do
memory requests as early as possible so that PND has schedule the
requests more intelligently. Currently we're still calculating
the watermarks as if VLV/CHV are identical to g4x, which isn't
the case.

The current code also seems to calculate insufficient watermarks
and hence we're seeing some underruns, especially on high resolution
displays.

To fix it just rip out the current code and replace is with something
that tries to utilize PND as efficiently as possible.

We now calculate the WM watermark to trigger when the FIFO still has
256us worth of data. 256us is the maximum deadline value supoorted by
PND, so issuing memory requests earlier would mean we probably couldn't
utilize the full FIFO as PND would attempt to return the data at
least in at least 256us. We also clamp the watermark to at least 8
cachelines as that's the magic watermark that enabling trickle feed
would also impose. I'm assuming it matches some burst size.

In theory we could just enable trickle feed and ignore the WM values,
except trickle feed doesn't work with max fifo mode anyway, so we'd
still need to calculate the SR watermarks. It seems cleaner to just
disable trickle feed and calculate all watermarks the same way. Also
trickle feed wouldn't account for the 256us max deadline value, thoguh
that may be a moot point in non-max fifo mode sicne the FIFOs are fairly
small.

On VLV max fifo mode can be used with either primary or sprite planes.
So the code now also checks all the planes (apart from the cursor)
when calculating the SR plane watermark.

We don't have to worry about the WM1 watermarks since we're using the
PND deadline scheme which means the hardware ignores WM1 values.

v2: Use plane->state->fb instead of plane->fb
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Existing watermark code calls intel_crtc_active() to determine whether a CRTC
is active for the purpose of watermark calculations (and bails out early if it
determines the CRTC is not active).  However intel_crtc_active() only returns
true if crtc->primary->fb is non-NULL, which isn't appropriate in the modern
age of universal planes and atomic modeset since userspace can now disable the
primary plane, but leave the CRTC (and other planes) running.

Note that commit

        commit 0fda6568
        Author: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
        Date:   Fri Feb 27 15:12:35 2015 +0000

            drm/i915/skl: Update watermarks for Y tiling

adds a test for primary plane enable/disable to trigger a watermark update
(previously we ignored updates to primary planes, which wasn't really correct,
but we got lucky since we always pretended the primary plane was on).  Tvrtko's
patch tries to update watermarks when we re-enable the primary plane, but that
watermark computation gets aborted early because intel_crtc_active() returns
false due to the disabled primary plane.

Switch the ILK and SKL watermark code over to use crtc->state->active rather
than calling intel_crtc_active() so that we'll properly compute watermarks when
re-enabling the primary plane.

Note that this commit doesn't touch callsites in the watermark code for
older platforms since there were concerns that doing so would lead to
other types of breakage.

Also note that all of the watermark calculation at the moment takes place after
new crtc/plane states are swapped into the DRM objects.  This will change in
the future, so we'll be working with in-flight state objects, but for the time
being, crtc->state is what we want to operate on.

v2: Don't drop primary->fb check from intel_crtc_active(), but rather replace
    ILK/SKL callsites with direct tests of crtc->state->active.  There is
    concern that messing with intel_crtc_active() will lead to other breakage for
    old hardware platforms.  (Ville)

v3: Use intel_crtc->active for now rather than crtc->state->active since
    we don't have CRTC states properly hooked up and initialized yet.
    We'll defer the switch to crtc->state->active until the atomic CRTC
    state work is farther along. (Ville)

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Poke at the CBR1_VLV register during init_clock_gating to make sure the
PND deadline scheme is used.

The hardware has two modes of operation wrt. watermarks:

1) PND deadline mode:
 - memory request deadline is calculated from actual FIFO level * DDL
 - WM1 watermark values are unused (AFAIK)
 - WM watermark level defines when to start fetching data from memory
   (assuming trickle feed is not used)

2) backup mode
 - deadline is based on FIFO status, DDL is unused
 - FIFO split into three regions with WM and WM1 watermarks, each
   part specifying a different FIFO status

We want to use the PND deadline mode, so let's make sure the chicken
bit is in the correct position on init.

Also take the opportunity to refactor the shared code between VLV and
CHV to a shared function.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

VLV/CHV have similar DSPARB registers as older platforms, just more of
them due to more planes. Add a bit of code to read out the current FIFO
split from the registers. Will be useful later when we improve the WM
calculations.

v2: Add display_mmio_offset to DSPARB
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that we have drm_planes for the cursor and primary we can move the
pixel_size handling into vlv_compute_drain_latency() and just pass the
appropriate plane to it.

v2: Check plane->state->fb instead of plane->fb

Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org> (v1)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Resolve conflict with Matt's s/plane->fb/plane->state->fb/
patch.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Introduce struct vlv_wm_values to house VLV watermark/drain latency
values. We start by using it when computing the drain latency values.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move the DDL precision handling into vlv_compute_drain_latency() so the
callers don't have to duplicate the same code to deal with it.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The current drain lantency computation relies on hardcoded limits to
determine when the to use the low vs. high precision multiplier.
Rewrite the code to use a more straightforward approach.
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Kill the silly DRAIN_LATENCY_PRECISION_* defines and just use the raw
number instead.

v2: Move the sprite 32/16 -> 16/8 preision multiplier
    change to another patch (Jesse)
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Apparently we must yet halve the DDL drain latency from what we're
using currently. This little nugget is not in any spec, but came
down through the grapevine.

This makes the displays a bit more stable. Not quite fully stable but at
least they don't fall over immediately on driver load.

v2: Update high_precision in valleyview_update_sprite_wm() too (Jesse)
Reviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Apparently, this has never worked reliably and is currently disabled. Also, the
gains are not particularly impressive. Thus rather than try to keep unused code
from decaying and having to update it for other driver changes, it was decided
to simply remove it.

For: VIZ-5115
Signed-off-by: NJohn Harrison <John.C.Harrison@Intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Implicit usage of local variables in macros isn't exactly the greatest
thing in the world, especially when that variable is the drm device and
we want to move towards a broader use of the i915 device structure.

Let's make for_each_plane() take dev_priv as its first argument then.
Suggested-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: Chris Wilson <chris-wilson.co.uk>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

plane->fb is a legacy pointer that not always be up-to-date (or updated
early enough).  Make sure the watermark code uses plane->state->fb so
that we're always doing our calculations based on the correct
framebuffers.

This patch was generated by Coccinelle with the following semantic
patch:

        @@
        struct drm_plane *P;
        @@
        - P->fb
        + P->state->fb

v2: Rebase
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The cursor size fields in intel_crtc just duplicate the data from
cursor->state.crtc_{w,h} so we don't need them any more.  Worse, their
use in the watermark code actually introduces a subtle bug since they
don't get updated to mirror the state values until the plane commit
stage, which is *after* we've already used them to calculate new
watermark values.  This happens because we had to move watermark updates
slightly earlier (outside vblank evasion) in commit

        commit 32b7eeec
        Author: Matt Roper <matthew.d.roper@intel.com>
        Date:   Wed Dec 24 07:59:06 2014 -0800

            drm/i915: Refactor work that can sleep out of commit (v7)

Dropping the intel_crtc fields and just using the state values (which
are properly updated by the time watermark updates happen) should solve
the problem.

Aside from the actual removal of the struct fields (which are formatted
in a way that I couldn't figure out how to match in Coccinelle), the
rest of this patch was generated via the following semantic patch:

        // Drop assignment
        @@
        struct intel_crtc *C;
        struct drm_plane_state S;
        @@
        (
        - C->cursor_width = S.crtc_w;
        |
        - C->cursor_height = S.crtc_h;
        )

        // Replace usage
        @@
        struct intel_crtc *C;
        expression E;
        @@
        (
        - C->cursor_width
        + C->base.cursor->state->crtc_w
        |
        - C->cursor_height
        + C->base.cursor->state->crtc_h
        |
        - to_intel_crtc(E)->cursor_width
        + E->cursor->state->crtc_w
        |
        - to_intel_crtc(E)->cursor_height
        + E->cursor->state->crtc_h
        )

v2: Rebase

Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Joe Konno <joe.konno@linux.intel.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=89346Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Display watermarks need different programming for different tiling
modes.

Set the relevant flag so this happens during the plane commit and
add relevant data into a structure made available to the watermark
computation code.

v2: Pass in tiling info to sprite plane updates as well.
v3: Rebased for plane handling changes.
v4: Handle fb == NULL when plane is disabled.
v5: Refactored for addfb2 interface.
v6: Refactored for fb modifier changes.
v7: Updated for atomic commit by only updating watermarks when tiling changes.
v8: BSpec watermark calculation updates.
v9: Restrict scope of y_tile_minimum variable. (Damien Lespiau)
v10: Get fb from plane state otherwise we are working on old state.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Acked-by: NAnder Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Acked-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: Damien Lespiau <damien.lespiau@intel.com> (v9)
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Recent BSpect updates have changed the watermark calculation to avoid
display flickering in some cases.

v2: Fix check against DDB allocation and tidy the code a bit. (Damien Lespiau)
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

I overlooked the fact that we need to allocate a minimum 8 blocks and
that just allocating the planes depending on how much they need to fetch
from the DDB in proportion of how much memory bw is necessary for the
whole display can lead to cases where we don't respect those minima (and
thus overrun).

So, instead, start by allocating 8 blocks to each active display plane
and then allocate the remaining blocks like before.

v2: Rebase on top of -nightly

Cc: Mahesh Kumar <mahesh1.kumar@intel.com>
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This W/A is put in a gen9 specific function because it may well be
needed on other gen9 platforms.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Let's also take the opportunity the remove the comment telling it's a
pre-prod W/A, it should be obvious from the stepping test.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

We'll gather cross-gen9 W/A in a separate function later.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Reviewed-by: NNick Hoath <nicholas.hoath@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

With Intel GVT-g, GPU power management is controlled by
host driver, so there is no need to provide virtualized
GPU PM support. In the future it might be useful to gather
VM input for freq boost, but now let's disable it simply.

v2:
take Chris' comments:
        - do not special case this to gen6+
Signed-off-by: NYu Zhang <yu.c.zhang@linux.intel.com>
Signed-off-by: NJike Song <jike.song@intel.com>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

When enabling new platforms, we may not have any W/A to apply,
especially that, now, a bunch of them have to be done from the ring.
Signed-off-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move Wa4x4STCOptimizationDisable to gen9_init_workarounds

v2: rebase
Signed-off-by: NNick Hoath <nicholas.hoath@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

v2: Add stepping check for WaDisableSDEUnitClockGating.
Signed-off-by: NNick Hoath <nicholas.hoath@intel.com>
Reviewed-by: NDamien Lespiau <damien.lespiau@intel.com>
[danvet: Rebase.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Move WaDisableDgMirrorFixInHalfSliceChicken5 to gen9_init_workarounds

v2: Added stepping check

v3: Removed unused register bitmap
Signed-off-by: NNick Hoath <nicholas.hoath@intel.com>
[danvet: Bikesheds.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>