Save additional filter tuple field shifts in tp_params based on
configured filter tuple fields.

Also, save the combined filter tuple mask based on configured
filter tuple fields.
Signed-off-by: NKumar Sanghvi <kumaras@chelsio.com>
Signed-off-by: NRahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: NGanesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Egil Hjelmeland says:

====================
net: dsa: lan9303: Fix STP and flooding issues

This patch set finishes the STP support, and fixes flooding issues.

Patch 1 fixes a flooding issue in the previous patch set.
Patch 2 finishes STP support by adding a ALR entry.
Patch 3 prevent duplicate flooding in HW and SW bridge.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The chip flood broadcast and unknown multicast frames.
On receive set skb->offload_fwd_mark to prevent the SW from flooding to the
same ports.

One exception: Because the ALR is set up to forward STP BPDUs only to CPU,
the SW bridge should flood STP BPDUs if local STP is not enabled.
This is archived by not setting skb->offload_fwd_mark on STP BPDUs.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

STP BPDUs arriving on user ports must sent to CPU port only,
for processing by the SW bridge.

Add an ALR entry with STP state override to fix that.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

lan9303_xmit_use_arl() introduced in previous patch set is wrong.
The chip flood broadcast and unknown multicast frames. The effect is that
broadcasts and multicasts are duplicated on egress. It is not possible to
configure the chip to direct unknown multicasts to CPU port only.

This means that only unicast frames can be transmitted using ALR lookup.
Signed-off-by: NEgil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The assignment to pointer msg is redundant as it is never read, so
remove msg.  Also remove the first assignment to qset as this is not
read before the next re-assignment of a new value to qset in the
for-loop. Cleans up two clang warnings:

drivers/net/ethernet/cavium/thunder/nic_main.c:589:2: warning: Value
stored to 'msg' is never read
drivers/net/ethernet/cavium/thunder/nic_main.c:611:2: warning: Value
stored to 'qset' is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It looks like the best place in MAINTAINERS data base to cover this
orphaned module.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ethernet FCS inclusion (rx-fcs) is supported on EF10 NICs, conditional on
 a firmware capability bit (MC_CMD_GET_CAPABILITIES_OUT_RX_INCLUDE_FCS).
To receive frames with bad FCS (rx-all) we just don't return the discard
 flag EFX_RX_PKT_DISCARD from efx_ef10_handle_rx_event_errors() or
 efx_farch_handle_rx_not_ok().
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Variable work_done is set to zero and this value is never read, instead
it is set to another value a few statements later.  Remove the redundant
assignment. Cleans up clang warning:

drivers/net/ethernet/cadence/macb_main.c:1221:2: warning: Value stored
to 'work_done' is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Tested-by: NAlexander Dahl <ada@thorsis.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

David reported breakages of VRF scenarios due to the
commit 6e617de8 ("net: avoid a full fib lookup when rp_filter is
disabled."): the local addresses based test is too strict when VRFs
are in place.

With this change we fall-back to a full lookup when custom fib rules
are in place; so that we address the VRF use case and possibly other
similar issues in non trivial setups.

v1 -> v2:
 - fix build breakage when CONFIG_IP_MULTIPLE_TABLES is not defined,
   reported by the kbuild test robot
Reported-by: NDavid Ahern <dsahern@gmail.com>
Fixes: 6e617de8 ("net: avoid a full fib lookup when rp_filter is disabled.")
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix to returnerror code -ENOMEM from the sctp_make_strreset_addstrm()
error handling case instead of 0. 'retval' can be overwritten to 0 after
call sctp_stream_alloc_out().

Fixes: e090abd0 ("sctp: factor out stream->out allocation")
Signed-off-by: NWei Yongjun <weiyongjun1@huawei.com>
Acked-by: NMarcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Acked-by: NNeil Horman <nhorman@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The pointer dev is being assigned but is never used, hence it is
redundant and can be removed. Cleans up clang warning:

drivers/net/usb/hso.c:2280:2: warning: Value stored to 'dev' is
never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Reviewed-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mutex_destroy only makes sense when enable DEBUG_MUTEX. For the
good readbility, it's better to invoke it in exit func when the init
func invokes mutex_init.
Signed-off-by: NGao Feng <gfree.wind@vip.163.com>
Acked-by: NGuillaume Nault <g.nault@alphalink.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Variable idx is being initialized and later on over-written by
a new value in a do-loop without the initial value ever being
read. Hence the initializion is redundant and can be removed.
Cleans up clang warning:

drivers/net/ethernet/alacritech/slicoss.c:358:15: warning: Value
stored to 'idx' during its initialization is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Acked-by: NLino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Florian Fainelli says:

====================
PHYLINK cosmetic and build fixes

Please find two small "fixes" one that corrects some stylistic changes and
another one that fixes an actual build failure in sfp.c. Since PHYLINK is
not directly visible to user, and there are no in-tree users yet (coming)
this is not targeted at "net" but "net-next" instead.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

include/gpio.h does not contain the references we want, we should be including
linux/gpio/consumer.h instead.

Fixes: 73970055 ("sfp: add SFP module support")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Perform a number of stylistic changes to phylink.c, sfp.c and sfp-bus.c:

- align with netdev-style comments
- align function arguments to the opening parenthesis
- remove blank lines
- fixup a few lines over 80 columns
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

to address common misconceptions about what BPF is and what it's not
add short BPF Q&A that clarifies core BPF design principles and
answers some common questions.
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NDaniel Borkmann <daniel@iogearbox.net>
Acked-by: NJohn Fastabend <john.fastabend@gmail.com>
Acked-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the error messages displayed in kernel log to include
hwaddress of the source machine that caused ipv6 duplicate address
detection failures.

Examples:

a) When we receive a NA packet from another machine advertising our
address:

ICMPv6: NA: 34:ab:cd:56:11:e8 advertised our address 2001:db8:: on eth0!

b) When we detect DAD failure during address assignment to an interface:

IPv6: eth0: IPv6 duplicate address 2001:db8:: used by 34:ab:cd:56:11:e8
detected!

v2:
    Changed %pI6 to %pI6c in ndisc_recv_na()
    Chaged the v6 address in the commit message to 2001:db8::
Suggested-by: NIgor Lubashev <ilubashe@akamai.com>
Signed-off-by: NVishwanath Pai <vpai@akamai.com>
Acked-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Have b53_hdr_setup() check what kind of tagging protocol is configured
(Broadcom or none) and apply the correct settings in both cases.
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Gustavo A. R. Silva says:

====================
netrom: refactor code and mark expected switch fall-throughs

The aim of this patchset is firstly to refactor code in nr_route.c in order to make it
easier to read and maintain and, secondly, to mark some expected switch fall-throughs
in preparation to enabling -Wimplicit-fallthrough.

I have to mention that I did not implement any unit test.
If someone has any suggestions on how I could test this piece of code
it'd be greatly appreciated.

Changes in v2:
 - Make use of the swap macro and remove inline keyword as suggested by
   Walter Harms and Kevin Dawson.

Changes in v3:
 - Update subject for both patches.
 - Add this cover letter as suggested by David Miller.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Code refactoring in order to make the code easier to read and maintain.
Signed-off-by: NGustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Jon Maloy <jon.maloy@ericsson.com>
Cc: Ying Xue <ying.xue@windriver.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: netdev@vger.kernel.org
Cc: tipc-discussion@lists.sourceforge.net
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: "David S. Miller" <davem@davemloft.net>
Cc: Philippe Reynes <tremyfr@gmail.com>
Cc: "yuval.shaia@oracle.com" <yuval.shaia@oracle.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: netdev@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.

Cc: Jon Mason <jdmason@kudzu.us>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Allen Hubbe <Allen.Hubbe@emc.com>
Cc: linux-ntb@googlegroups.com
Cc: netdev@vger.kernel.org
Signed-off-by: NKees Cook <keescook@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

During perf event attaching/detaching bpf programs,
the tp_event->prog_array change is protected by the
bpf_event_mutex lock in both attaching and deteching
functions. Although tp_event->prog_array is a rcu
pointer, rcu_derefrence is not needed to access it
since mutex lock will guarantee ordering.

Verified through "make C=2" that sparse
locking check still happy with the new change.

Also change the label name in perf_event_{attach,detach}_bpf_prog
from "out" to "unlock" to reflect the code action after the label.
Signed-off-by: NYonghong Song <yhs@fb.com>
Acked-by: NAlexei Starovoitov <ast@kernel.org>
Acked-by: NMartin KaFai Lau <kafai@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Using SIT tunnels with VRFs works fine if the underlay device is in a
VRF and the link parameter is set to the VRF device. e.g.,

    ip tunnel add jtun mode sit remote <addr> local <addr> dev myvrf

Update the device check to allow the link to be the enslaved device as
well. e.g.,

    ip tunnel add jtun mode sit remote <addr> local <addr> dev eth4

where eth4 is enslaved to myvrf.
Reported-by: NJeff Barnhill <0xeffeff@gmail.com>
Signed-off-by: NDavid Ahern <dsahern@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: NArvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add an entry for IFLA_BRPORT_NEIGH_SUPPRESS to bridge port policies.

Fixes: 821f1b21 ("bridge: add new BR_NEIGH_SUPPRESS port flag to suppress arp and nd flood")
Signed-off-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Acked-by: NRoopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Antoine Tenart says:

====================
net: mvpp2: various improvements

This series includes various patches improving the Marvell PPv2 driver.
I send them as a series to avoid any possible merge conflict.

- Patches 1 and 2 improve the initializing of the Tx and Rx FIFO.
- Patch 3 initialize the RSS table to evenly distribute the ingress
  packets across multiple Rx queues based on their hashes.
- Patch 4 limits the number of TSO segments sent to the driver, to avoid
  having more segments to handle than the corresponding number of
  available descriptors.
- Patch 5 and 6 are cosmetic improvements.

This applies on today's net-next branch, The patches were tested
extensively (I ran iperf and http downloads in parallel, transferring
TBs of data).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Two functions were always used to set the DMA addresses in Tx
descriptors, because this address is split into a base+offset in the
descriptors. A mask was used to come up with the base and offset
addresses and two functions were called, mvpp2_txdesc_dma_addr_set() and
mvpp2_txdesc_offset_set().

This patch moves the base+offset calculation logic to
mvpp2_txdesc_dma_addr_set(), and removes mvpp2_txdesc_offset_set() to
simplify things.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cosmetic patch using the MVPP2_AGGR_TXQ_SIZE everywhere instead of the
size field of aggr_txq, as the size never change and is always equal to
the MVPP2_AGGR_TXQ_SIZE define.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Too many TSO descriptors can be required for the default queue size,
when using small MSS values for example. Prevent this by adding a
maximum number of allowed TSO segments (300). In addition set a stop and
a wake thresholds to stop the queue when there's no room for a 1 "worst
case scenario skb". Wake up the queue when the number of descriptors is
low enough.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch initialize the RSS tables to evenly (depending on the packets
RSS hashes) distribute the packets across port Rx queues. This helps to
handle packets on different CPUs to improve performances, as more queues
will be used in parallel.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

So far only the Rx FIFO size was initialized. For PPv2.2 the Tx FIFO
size can be set as well. This patch initializes the Tx FIFO size for
PPv2.2 controllers to 3K.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Rx FIFO size was set to the same value for all ports. This patch
sets it depending on the maximum speed a given port can handle. This is
only working for PPv2.2.
Signed-off-by: NAntoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Steffen Klassert says:

====================
pull request (net-next): ipsec-next 2017-10-30

1) Change some variables that can't be negative
   from int to unsigned int. From Alexey Dobriyan.

2) Remove a redundant header initialization in esp6.
   From Colin Ian King.

3) Some BUG to BUG_ON conversions.
   From Gustavo A. R. Silva.

Please pull or let me know if there are problems.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Variable len is being assigned a value that is never read,
hence the assignment is redundant and can be removed. Cleans
up clang warning:

drivers/net/hamradio/mkiss.c:443:3: warning: Value stored to
'len' is never read
Signed-off-by: NColin Ian King <colin.king@canonical.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

sockmap test is using two programs that use bpf_trace_printk()
which prints into trace_pipe, but nothing is reading it.
Remove it.

Fixes: 6f6d33f3 ("bpf: selftests add sockmap tests")
Signed-off-by: NAlexei Starovoitov <ast@kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>