This driver used to be tied to the addi-data common code which
always saved the start address of pci bars 0, 1, 2, and 3 for
use by the driver. This driver only uses pci bar 2.

Remove all the non-used pci bars and move the saving of pci bar
2 so it occurs right after the pci device is enabled.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make comedi_pci_enable() use the same parameter type as
comedi_pci_disable(). This also allows comedi_pci_enable
to automatically determine the resource name passed to
pci_request_regions().

Make sure the errno value returned is passed on instead of
assuming an errno. Also, remove any kernel noise that is
generated when the call fails.

The National Instruments drivers that use the mite module
currently enable the PCI device in the mite module. For
those drivers move the call to comedi_pci_enable into the
driver.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently all the comedi PCI drivers need to do some checking in
their (*detach) before calling comedi_pci_disable() in order to
make sure the PCI device has actually be enabled.

Change the parameter passed to comedi_pci_disable() from a struct
pci_dev pointer to a comedi_device pointer and have comedi_pci_disable()
handle all the checking.

For most comedi PCI drivers this also allows removing the local
variable holding the pointer to the pci_dev. For some of the drivers
comedi_pci_disable can now be used directly as the (*detach) function.

The National Instruments drivers that use the mite module currently
enable/disable the PCI device in the mite module. For those drivers
move the call to comedi_pci_disable into the driver and make sure
dev->iobase is set to a non-zero value.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A cleanup patch to remove sparse warnings caused by my other patch
"procfs: Improve Scaling in proc" since now proc_fops is protected by the rcu.
Signed-off-by: NNathan Zimmer <nzimmer@sgi.com>
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Kconfig entry for the "Anonymous Shared Memory Subsystem" got added
in v3.3. It has an optional dependency on TINY_SHMEM. But TINY_SHMEM had
already been removed in v2.6.29. So this optional dependency can safely
be removed too.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

got the warnings

drivers/staging/csr/sme_wext.c: In function ‘unifi_siwscan’:
drivers/staging/csr/sme_wext.c:1276:9: warning: variable ‘scantype’ set but not used [-Wunused-but-set-variable]

fixed by removing the variable
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This is a patch to usbdux.c that fixes the camel case warnings found
by the checkpatch.pl tool
Signed-off-by: NJacob Garber <ajtgarber@gmail.com>
Reviewed-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Acked-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix some compiler warnings when building for i386 arch. Reported by
Fengguang's build-bot.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The following commits introduced a couple build errors in this driver
due to the removal of some macros in ni_stc.h.

commit: f5a1d92b "staging: comedi: ni_stc.h: remove n_ni_boards macro"
commit: 6293e357 "staging: comedi: ni_stc.h: remove boardtype macro"

The n_ni_boards macro is an open coded version of ARRAY_SIZE.

The boardtype macro is removed in favor of using the comedi_board()
helper and accessing the boardinfo with a pointer.

Fix both issues.
Reported-by: Nkbuild test robot <fengguang.wu@intel.com>
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

remove cast for kmalloc return value.
Signed-off-by: NZhang Yanfei <zhangyanfei@cn.fujitsu.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

should be err < 0 instead of if (err) which actually the read register
value can be a positive number
Acked-by: NMark Einon <mark.einon@gmail.com>
Signed-off-by: NDevendra Naga <devendra.aaru@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

New comedi driver for Advantech PCI-1724U with modifications by Ian
Abbott <abbotti@mev.co.uk>.
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Cc: Frank Mori Hess <fmh6jj@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The Advantech PCI-1710HG is similar to the PCI-1710 but has a different
set of ranges for analog input (HG = high gain).  Because they share the
same PCI vendor and device ID, the adv_pci1710 driver does not currently
distinguish them.  This is more of a problem since auto-configuration
code was added to the driver (and manual configuration support removed),
as the PCI-1710HG would be automatically configured as a PCI-1710.  More
recently, the unused code for PCI-1710HG support was #ifdef'ed out.

In fact, the PCI-1710 and PCI-1710HG can be distinguished by considering
the PCI subvendor and subdevice IDs according to the following table:

vendor device subven subdev model        treat as
====== ====== ====== ====== ============ ==========
0x13fe 0x1710 0x10b5 0x9050 PCI-1710S    PCI-1710
0x13fe 0x1710 0x13fe 0x0000 PCI-1710     PCI-1710
0x13fe 0x1710 0x13fe 0xb100 PCI-1710B    PCI-1710
0x13fe 0x1710 0x13fe 0xb200 PCI-1710B2   PCI-1710
0x13fe 0x1710 0x13fe 0xc100 PCI-1710C    PCI-1710
0x13fe 0x1710 0x13fe 0xc200 PCI-1710C2   PCI-1710
0x13fe 0x1710 0x1000 0xd100 PCI-1710U    PCI-1710
0x13fe 0x1710 0x13fe 0x0002 PCI-1710HG   PCI-1710HG
0x13fe 0x1710 0x13fe 0xb102 PCI-1710HGB  PCI-1710HG
0x13fe 0x1710 0x13fe 0xb202 PCI-1710HGB2 PCI-1710HG
0x13fe 0x1710 0x13fe 0xc102 PCI-1710HGC  PCI-1710HG
0x13fe 0x1710 0x13fe 0xc202 PCI-1710HGC2 PCI-1710HG
0x13fe 0x1710 0x1000 0xd102 PCI-1710HGU  PCI-1710HG

The above information is extracted from Advantech's own GPL'ed Linux
(non-Comedi) driver source from "advdaq-1.10.0001-1.tar.bz2" on their
website.

(0x13fe = PCI_VENDOR_ID_ADVANTECH, 0x10b5 = PCI_VENDOR_ID_PLX, 0x9050 =
PCI_DEVICE_ID_PLX_9050, 0x1000 = PCI_VENDOR_ID_NCR or
PCI_VENDOR_ID_LSI_LOGIC but I assume this subvendor ID was chosen
"randomly".)
Signed-off-by: NIan Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add the DWC2 Kconfig and Makefile, and modify the staging Kconfig and
Makefile to include them
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add myself as maintainer of the DWC2 driver
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This file contains the PCI bus interface "glue" for the DWC2 driver
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This file contains code to support the HCD descriptor DMA mode of
the controller
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

These files contain the HCD code, and implement the Linux
hc_driver API. Support for both slave mode and buffer DMA mode
of the controller is included.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The core code provides basic services for accessing and managing
the DWC_otg hardware. These services are used by both the Host
Controller Driver and (in future) the Peripheral Controller Driver.
Signed-off-by: NPaul Zimmerman <paulz@synopsys.com>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add support for the Network Accelerator Engine on Netlogic XLR/XLS
MIPS SoCs. The XLR/XLS NAE blocks can be configured as one 10G
interface or four 1G interfaces. This driver supports blocks
with 1G ports.
Signed-off-by: NGanesan Ramalingam <ganesanr@broadcom.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

In case of error, the function anon_inode_getfile() returns
ERR_PTR() and never returns NULL. The NULL test in the return
value check should be replaced with IS_ERR().
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove duplicated include.
Signed-off-by: NWei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Correct spelling typos in staging/comedi
Signed-off-by: NMasanari Iida <standby24x7@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Format the multi-line comments in the kernel CodingStyle.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Remove all the unnecessary includes.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The PCI device id is only used in the device table. Remove the
define and just open code the device id.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The (*insn_read) and (*insn_write) functions for all the subdevices
in this driver are the same except for the 'offset' that is added
to the iobase and channel to read/write a register on the board.

Pass the 'offset' in s->private so we can use the same (*insn_read)
and (*insn->write) functions for all the subdevices.

Also, fix the (*insn_read) and (*insn_write) functions so they work
correctly. The comedi core expects them to read/write insn->n data
values and then return the number of values used.

For aesthetic reasons, add some whitespace to the subdevice init.

Remove the dev_info() noise at the end of the attach.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The low-level i/o functions in this driver simply read/write a
register based on the channel in insn->chanspec and an offset.

Create a macro, PCI8164_AXIS(), that takes the channel number as
a parameter and returns the register value.

Remove the switch() statements used to figure out the 'axis_reg'
and use the new macro instead.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The dev_dbg() messages in the adl_pci8164_insn_{read,out} functions
output the 'data' that was read/write to the device. Two 'data' values
are always printed, data[0] and data[1].

The 'data' pointer points to an array of unsigned int values. The number
of values in the array is indicated by insn->n. The number of data
elements is never checked so the dev_dbg() could be trying to access
a 'data' element that is invalid.

Instead of fixing the dev_dbg() just remove them. They are really just
added noise.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

With the bus specific code split out, the device id in the boardinfo
is no longer needed. Remove it.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The vendor/device ids in the boardinfo are not longer needed. Remove
them.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver only uses the boardinfo to get the dev->board_name.
Just use the dev->driver->driver_name and remove the unnecessary
boardinfo completely.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Only one board type is supported by this driver. Remove the 'interrupt'
field from the boardinfo and just call the function directly in
v_ADDI_Interrupt().
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

All the users of the addi_common code now set the dev->board_ptr
before calling addi_auto_attach(). Remove the unnecessary function
that searches for the boardinfo.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Create an enum to the boardinfo and pass that enum in the pci_driver
id_table as the driver_data.

Change the macro used to fill in the device table from PCI_DEVICE()
to PCI_VDEVICE(). This allows passing the enum as the next field.

Set the dev->board_ptr before calling addi_auto_attach(). This
removes the need for the common code to search for the boardinfo.

Since the search is not done we can remove the unnecessary board
information from the comedi_driver.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Create an enum to the boardinfo and pass that enum in the pci_driver
id_table as the driver_data.

Change the macro used to fill in the device table from PCI_DEVICE()
to PCI_VDEVICE(). This allows passing the enum as the next field.

Set the dev->board_ptr before calling addi_auto_attach(). This
removes the need for the common code to search for the boardinfo.

Since the search is not done we can remove the unnecessary board
information from the comedi_driver.

For aesthetic reasons, move the pci device table near the pci_driver.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver only supports a single PCI device. If we set the
dev->board_ptr before calling addi_auto_attach() we remove
the need for the common code to search for the boardinfo.

Since the search is not done we can remove the unnecessary
board information from the comedi_driver.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver only supports a single PCI device. If we set the
dev->board_ptr before calling addi_auto_attach() we remove
the need for the common code to search for the boardinfo.

Since the search is not done we can remove the unnecessary
board information from the comedi_driver.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This driver only supports a single PCI device. If we set the
dev->board_ptr before calling addi_auto_attach() we remove
the need for the common code to search for the boardinfo.

Since the search is not done we can remove the unnecessary
board information from the comedi_driver.
Signed-off-by: NH Hartley Sweeten <hsweeten@visionengravers.com>
Cc: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>