Now, the driver sends arp probes for all unresolved neighbours that are
currently a nexthop for some route on the system. The job is set
periodically every 5 seconds.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For nexthop neighbours we need to make kernel to think there is a traffic
flowing to them preventing it from going to stale state. Otherwise
kernel would stale it and eventually the neigh would be removed from HW
and nexthop as well. That would reduce ECMP group in HW.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement next-hop routing offload including ECMP. To make it possible,
introduce next-hop group entity. This entity keeps track of resolved
neighbours and updates HW adjacency table accordingly. Note that HW
next-hops are stored in this adjacency table, in form of MAC.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is a very simple manager for KVD linear area. Currently, the
allocator will either allocate a single entry from pre-defined sub-area,
or in case more than one entry is needed, it will allocate 32-entry chunk
in other pre-defined sub-area.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Override the defaults and define the area sizes ourselves.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As previously explained, the driver should periodically poll the device
for neighbours activity according to the configured DELAY_PROBE_TIME.
This will prevent active neighbours from staying in STALE state for long
periods of time.

During init configure the polling interval according to the
DELAY_PROBE_TIME used in the default table. In addition, register a
netevent notification block, so that the interval is updated whenever
DELAY_PROBE_TIME changes.

Using the computed interval schedule a delayed work, which will update
the kernel via neigh_event_send() on any active neighbour since the last
delayed work.
Signed-off-by: NYotam Gigi <yotamg@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We need to hold some private data for every neigh entry. It would be
possible to do it using neigh_priv_len/ndo_neigh_construct/
ndo_neigh_destroy however only for the port device itself. That would not
work for stacked devices like bridge/team/bond. So introduce a private
neigh table. Hook onto ndos neigh_construct/destroy and add/remove
table entry according to that.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As with the previously introduced L3 interfaces, listen to 'inetaddr'
notifications sent for bridges devices configured on top of the port
netdevs and create / destroy router interfaces (RIFs) accordingly.
This also includes VLAN devices configured on top of the VLAN-aware
bridge.

The RIFs will be destroyed either when the last IP address is removed or
when the underlying FID is is destroyed.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Before introducing support for L3 interfaces on top of the VLAN-aware
bridge we need to add some missing infrastructure.

Such an interface can either be the bridge device itself or a VLAN
device on top of it. In the first case the router interface (RIF) is
associated with FID 1, which is created whenever the first port netdev
joins the bridge. We currently assume the default PVID is 1 and that
it's already created, as it seems reasonable. This can be extended in
the future.

However, in the second case it's entirely possible we've yet to create a
matching FID. This can happen if the VLAN device was configured before
making any bridge port member in the VLAN.

Prevent such ordering problems by using the VLAN device's CHANGEUPPER
event to configure the FID. Make the VLAN device hold a reference to the
FID and prevent it from being destroyed even if none of the port netdevs
is using it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previous commit deprecated the vFIDs used to get traffic to the CPU
('port_vfids'). Thus, we now use the vFIDs as god intended and the
artificial split is no longer needed.

Rename functions and variables to reflect that.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we only supported bridged interfaces. Packets ingressing
through the switch ports were either classified to FIDs (in the case of
the VLAN-aware bridge) or vFIDs (in the case of VLAN-unaware bridges).
The packets were then forwarded according to the FDB. Routing was done
entirely in slowpath, by splitting the vFID range in two and using the
lower 0.5K vFIDs as dummy bridges that simply flooded all incoming
traffic to the CPU.

Instead, allow packets to be routed in the device by creating router
interfaces (RIFs) that will direct them to the router block.
Specifically, the RIFs introduced here are Sub-port RIFs used for VLAN
devices and port netdevs. Packets ingressing from the {Port / LAG ID, VID}
with which the RIF was programmed with will be assigned to a special
kind of FIDs called rFIDs and from there directed to the router.

Create a RIF whenever the first IPv4 address was programmed on a VLAN /
LAG / port netdev. Destroy it upon removal of the last IPv4 address.
Receive these notifications by registering for the 'inetaddr'
notification chain. A non-zero (10) priority is used for the
notification block, so that RIFs will be created before routes are
offloaded via FIB code.

Note that another trigger for RIF destruction are CHANGEUPPER
notifications causing the underlying FID's reference count to go down to
zero. This can happen, for example, when a VLAN netdev with an IP address
is put under bridge. While this configuration doesn't make sense it does
cause the device and the kernel to get out of sync when the netdev is
unbridged. We intend to address this in the future, hopefully in current
cycle.

Finally, Remove the lower 0.5K vFIDs, as they are deprecated by the RIFs,
which will trap packets according to their DIP.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are just about to introduce router interfaces (RIFs), but before that
we need to be able update the device with the correct RIF attributes
whenever they change for the netdev the RIF is backing. Two such
attributes are MTU and MAC.

The MAC is used both to set the source MAC of packets egressing from the
RIF and also to program an FDB rule that will direct packets to the
router block.

Use the existing netdevice notification block and respond to CHANGEADDR
and CHANGEMTU accordingly. Store both attributes in the RIF struct
in case we need to revert to old attributes following a failed update.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add functions that iterate over lower devices and find port device.
As a dependency add netdev_for_each_all_lower_dev and
netdev_for_each_all_lower_dev_rcu macro with
netdev_all_lower_get_next and netdev_all_lower_get_next_rcu shelpers.

Also, add functions to return mlxsw struct according to lower device
found and mlxsw_port struct with a reference to lower device.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement ipv4 FIB entries addition and removal. Initially, we support
local and broadcast routes using "ip2me" trap action.
Also, unicast routes without nexthop are supported using "local" action.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Virtual router is a construct used inside HW. In this implementation
we map kernel tables to virtual routers one to one. Introduce management
logic to create virtual routers when needed and destroy in case they are
no longer in use. According to that, call into LPM tree management.
Each virtual router is always bound to one LPM tree.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce basic LPM tree management allowing to share the trees in
between tables if the used prefixes in the tables are the same.
Build the tree structure according to the used prefixes. Although it is
not optimal for many use cases, this initial implementation does only
simple linear left-tree. More advanced structures will be introduced
later on, possibly including mechanisms to change trees on the fly.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Shadow FIB is needed in order to hold additional information for FIB
entries and keep track of used prefixes. That is needed for the LPM tree
construction to be introduced later on in this set.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When enabling the router in the device we will represent L3 netdevs
using router interfaces (RIFs). These will be specified whenever
programming routes or neighbours on the netdev.

Introduce the basic RIF infrastructure which allows one to lookup a RIF
by its netdev. Later patches in the series will extend this, but the
basic routines are needed now in order to direct traffic to CPU.

Pointers to the RIF structs are stored in an array indexed by the RIF's
number. This will allow us to efficiently update the kernel's neighbour
table when regularly dumping the device's table.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Create a skeleton router file and do basic HW initialization of router.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When port isn't bridged it is still possible to invoke switchdev ops and
configure the device's VLAN filters.

However, this will require us to use different Router InterFaces (RIFs)
for the same netdev, instead of one per-netdev as with any other
configuration.

Taking the above into account and the fact that this functionality is
questionable with regards to the device's normal use-case, remove it and
instead return an error.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are situations in which a vPort is destroyed while still holding
references to device's resources such as FIDs and FDB records. This can
happen, for example, when a VLAN device is deleted while still being
bridged.

Instead of trying to make sure vPort destruction is invoked when it no
longer uses device's resources, just free them upon destruction. This
simplifies the code, as we no longer need to take different situations
into account when events are received - cleanup is taken care of in one
place.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

FDB entries are learned using {Port / LAG ID, FID} and therefore should
be flushed whenever a port (vPort) leaves its FID (vFID).

However, when the bridge port is a LAG device (or a VLAN device on top),
then FDB flushing is conditional. Ports removed from such LAG
configurations must not trigger flushing, as other ports might still be
members in the LAG and therefore the bridge port is still active.

The decision whether to flush or not was previously computed in the
netdevice notification block, but in order to flush the entries when a
port leaves its FID this decision should be computed there.

Strip the notification block from this logic and instead move it to one
FDB flushing function that is invoked from both the FID / vFID leave
functions.

When port isn't member in LAG, FDB flushing should always occur.
Otherwise, it should occur only when the last port (vPort) member in the
LAG leaves the FID (vFID).

This will allow us - in the next patch - to simplify the cleanup code
paths that are hit whenever the topology above the port netdevs changes.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Not all vPorts will have FIDs assigned to them, so make sure functions
first test for FID presence.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As previously explained, not all vPorts will be assigned FIDs, so instead
of returning the FID index of a vPort, return a pointer to its FID
struct. This will allow us to know whether it's legal to access the
vPort's FID parameters such as index and device.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When L3 interfaces will be introduced a vPort won't necessarily have a
FID assigned to it. This can happen if it's not member in a bridge (in
which case it's assigned a vFID) or doesn't have an IP address (in which
case it's assigned an rFID).

Therefore, instead check the VID parameter to test whether a port is a
vPort or not.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In a very similar way to the vFIDs, make the first 4K FIDs - used in the
VLAN-aware bridge - use the new FID struct.

Upon first use of the FID by any of the ports do the following:

1) Create the FID
2) Setup a matching flooding entry
3) Create a mapping for the FID

Unlike vFIDs, upon creation of a FID we always create a global
VID-to-FID mapping, so that ports without upper vPorts can use it
instead of creating an explicit {Port, VID} to FID mapping.

When a port leaves a FID the reverse is performed. Whenever the FID's
reference count reaches zero the FID is deleted along with the global
mapping.

The per-FID struct will later allow us to configure L3 interfaces on top
of the VLAN-aware bridge.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now we had a dedicated struct only for vFIDs, but before
introducing support for L3 interfaces we need to make it generic and
use it for all three types of FIDs:

1) FIDs - 0..4K-1, used for the VLAN-aware bridge
2) vFIDs - 4K..15K-1, used for VLAN-unaware bridges
3) rFIDs - 15K..16K-1, used to direct traffic to / from the router in
the device. Will be introduced later in the series.

The three types of L3 interfaces - Router InterFaces, RIFs - that will
be introduced correspond to the three types of FIDs and are configured
using them. Therefore, we'll need to store the links between them as
well as a reference count on the underlying FID, so that the
corresponding RIF will be destroyed when it reaches zero.

Note that the lower 0.5K vFIDs are currently used for for non-bridged
netdevs, so that traffic could be flooded to the CPU port. However, when
rFIDs will be introduced we'll no longer need these and they too will be
used for VLAN-unaware bridges.

Make the vFID struct generic by renaming it and some of its fields. FIDs
will be converted to use it later in the series.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use a FID index instead of vFID and ease the transition towards a
generic FID struct.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In all call sites 'only_uc' is set to false, so strip it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is a macro to do this kind of declarations, so use it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When rtnl_fill_ifinfo() is called for a certain netdevice it queries its
various parameters such as switch id and physical port name. The
function might get called in an atomic context, which means the
underlying driver must not sleep during the query operation.

Don't query the device and sleep during ndo_get_phys_port_name(), but
instead store the needed parameters in port creation time.

Fixes: 2bf9a586 ("mlxsw: spectrum: Add support for physical port names")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement occupancy API introduced in devlink and mlxsw core. This is
done by accessing SBPM register for Port-Pool and SBSR for Port-TC
current and max occupancy values. Max clear is implemented using the
same registers.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement previously introduced mlxsw core shared buffer API.
For Spectrum, that is done utilizing registers SBPR, SBCM and SBPM.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to achieve faster dumping of current setting and also in order
to provide possibility to get pool mode without a need to query hardware,
do cache the configuration in driver.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove devlink port reg/unreg from spectrum and switchx2 code and rather
do the common work in core. That also ensures code separation where
devlink is only used in core.c.
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the appropriate DCB ops and allow a user to configure certain
traffic classes as lossless.

The operation configures PFC for both the egress (respecting PFC frames)
and ingress (sending PFC frames) parts of the port.

At egress, when a PFC frame is received for a PFC enabled priority, then
all the priorities mapped to the same TC are stopped.

At ingress, the priority group (PG) buffers to which the enabled PFC
priorities are mapped are configured to be lossless. PFC frames will be
transmitted when the Xoff threshold is crossed.

The user-supplied delay parameter is used to determine the PG's size
according to the following formula:

PG_SIZE = PG_SIZE_LOSSY + delay * CELL_FACTOR + MTU

In the worst case scenario the delay will be made up of packets that
are all of size CELL_SIZE + 1, which means each packet will require
almost twice its true size when buffered in the switch. We therefore
multiply this value by the "cell factor", which is close to 2.

Another MTU is added in case the transmitting host already started
transmitting a maximum length frame when the PFC packet was received.

As with PAUSE enabled ports, when the port's MTU is changed both the
PGs' size and threshold are adjusted accordingly.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a packet ingress the switch it's placed in its assigned priority
group (PG) buffer in the port's headroom buffer while it goes through
the switch's pipeline. After going through the pipeline - which
determines its egress port(s) and traffic class - it's moved to the
switch's shared buffer awaiting transmission.

However, some packets are not eligible to enter the shared buffer due to
exceeded quotas or insufficient space. Marking their associated PGs as
lossless will cause the packets to accumulate in the PG buffer. Another
reason for packets accumulation are complicated pipelines (e.g.
involving a lot of ACLs).

To prevent packets from being dropped a user can enable PAUSE frames on
the port. This will mark all the active PGs as lossless and set their
size according to the maximum delay, as it's not configured by user.

                         +----------------+   +
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   | Delay
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   |
                         |                |   |
    Xon/Xoff threshold   +----------------+   +
                         |                |   |
                         |                |   | 2 * MTU
                         |                |   |
                         +----------------+   +

The delay (612 [Cells]) was calculated according to worst-case scenario
involving maximum MTU and 100m cables.

After marking the PGs as lossless the device is configured to respect
incoming PAUSE frames (Rx PAUSE) and generate PAUSE frames (Tx PAUSE)
according to user's settings.

Whenever the port's headroom configuration changes we take into account
the PAUSE configuration, so that we correctly set the PG's type (lossy /
lossless), size and threshold. This can happen when:

a) The port's MTU changes, as it directly affects the PG's size.

b) A PG is created following user configuration, by binding a priority
to it.

Note that the relevant SUPPORTED flags were already mistakenly set by
the driver before this commit.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Allow a user to set maximum rate for a particular TC using DCB ops.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Implement the appropriate DCB ops and allow a user to configure:
	* Priority to traffic class (TC) mapping with a total of 8
	  supported TCs
	* Transmission selection algorithm (TSA) for each TC and the
	  corresponding weights in case of weighted round robin (WRR)

As previously explained, we treat the priority group (PG) buffer in the
port's headroom as the ingress counterpart of the egress TC. Therefore,
when a certain priority to TC mapping is configured, we also configure
the port's headroom buffer.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Introduce basic infrastructure for DCB and add the missing ops in
following patches.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>