An hba-wide lock is taken in the nvme io completion routine. The lock
covers null'ing of the nrport pointer in the cmd structure.

The nrport member isn't necessary. After extracting the pointer from the
command, the pointer was dereferenced to get the fc discovery node
pointer. But the fc discovery node pointer is alrady in the command
structure so the dereferrence was unnecessary.

Eliminated the nrport structure member and its use, which also eliminates
the port-wide lock.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When calling debugfs functions, there is no need to ever check the return
value.  The function can work or not, but the code logic should never do
something different based on this.

Cc: James Smart <james.smart@broadcom.com>
Cc: Dick Kennedy <dick.kennedy@broadcom.com>
Cc: "James E.J. Bottomley" <jejb@linux.ibm.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update lpfc version to 12.0.0.10
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch adds a "pci_bus_reset" option to the board_mode sysfs attribute.
This option uses the pci_reset_bus() api to reset the PCIe link the adapter
is on, which will reset the chip/adapter.  Prior to issuing this option,
all functions on the same chip must be placed in the offline state by the
admin. After the reset, all of the instances may be brought online again.

The primary purpose of this functionality is to support cases where
firmware update required a chip reset but the admin did not want to reboot
the machine in order to instantiate the firmware update.

Sanity checks take place prior to the reset to ensure the adapter is the
sole entity on the PCIe bus and that all functions are in the offline
state.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Current messages report generic actions (like send GID_FT), but misses
reporting for what protocol type the action is taken.

Revise the messages to reflect the FC4 protocol type being worked on.

[mkp: typo]
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When a target's link dropped, an RSCN was received to communicate the
change. The driver detected the loss of the target and issued and UNREG_RPI
mailbox command.  While that was being processed, another RSCN was received
to communicate the port coming back.  The driver deferred the PLOGI to the
port until the mailbox command finishes. When the mailbox command completed
it saw the pending port and called the routines to issue the
PLOGI. However, it forgot to clear the UNREG_INP state flag, so the PLOGI
xmt routine nooped the PLOGI request assuming it needed to wait for the
mailbox command.  At this point, login would never be re-attempted.

Clear UNREG_INP before issuing the deferred PLOGI.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Currently, when a trunk link goes down due to some fault, the driver
snapshots the fault code.  If the link then comes back up, meaning there is
no fault, the driver is not clearing the fault code so the sysfs link_state
entry reports old/stale data.

Revise the logic so that on successful link up the fault code is cleared.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The existing MDS loopback diagnostics support processing received frames in
the slowpath work thread. It caps the number of frames it will process at
64, before waiting for another event to indicate additional frame
reception. The net-net is this results in very slow frame processing during
loopback tests and sometimes orphans an io, causing the loopback test to
report failure by the switch.

Move MDS loopback frame processing out of the slow path worker thread and
into the normal RQ processing routines.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If the adapter is taken offline, the trunk link port attributes continue to
report trunk links as up even though all links are down as the adapter is
offline.

Clear the trunk links state as part of taking the adapter offline.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Certain older adapters such as the OneConnect OCe10100 may not have a valid
wqpcnt value.  In this case, do not set queue->page_count to 0 in
lpfc_sli4_queue_alloc() as this will prevent the driver from initializing.

Fixes: 895427bd ("scsi: lpfc: NVME Initiator: Base modifications")
Cc: stable@vger.kernel.org # 4.11+
Signed-off-by: NEwan D. Milne <emilne@redhat.com>
Reviewed-by: NLaurence Oberman <loberman@redhat.com>
Tested-by: NLaurence Oberman <loberman@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Most SCSI drivers want to enable "clustering", that is merging of
segments so that they might span more than a single page.  Remove the
ENABLE_CLUSTERING define, and require drivers to explicitly set
DISABLE_CLUSTERING to disable this feature.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Addition of support for if_type=6 missed several checks for interface type,
resulting in the failure of several key management features such as
firmware dump and loopback testing.

Correct the checks on the if_type so that both SLI4 IF_TYPE's 2 and 6 are
supported.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NEwan D. Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This reverts commit 287aba25.

We killed the bad firmware and this mod is no longer necessary.
Signed-off-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update the driver version to 12.0.0.9
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When dif and first burst is used in a write command wqe, the driver was not
properly setting fields in the io command request. This resulted in no dif
bytes being sent and invalid xfer_rdy's, resulting in the io being aborted
by the hardware.

Correct the wqe initializaton when both dif and first burst are used.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

On driver termination, after the driver stops fw logging by writing a
register on the chip, the driver immediately unmaps and frees the logging
buffer, without confirming in any way that the chip has received the write
and terminated the logging. As termination on the chip is not immediate,
the chip may issue a dma request to the now unmapped dma buffer, resulting
in a iommu fault.

Change the driver to receive a confirmation that logging ahs been
terminated. As the driver always issues an SLI reset with the device as
part of shutdown, and as part of that is receiving confirmation that the
reset is complete - the driver was modified to perform the write to disable
fw logging prior to the SLI reset and only free the fw log buffer after the
SLI reset is complete. That guarantees use of the fw log buffer is fully
terminated when it is unmapped.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver missed classifying the chip type for G7 when reporting supported
topologies. This resulted in loop being shown as supported on FC links that
are not supported per the standard.

Add the chip classifications to the topology checks in the driver.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver is setting bits in word 10 of the SLI4 ABORT WQE (the wqid).  The
field was a carry over from a prior SLI revision. The field does not exist
in SLI4, and the action may result in an overlap with future definition of
the WQE.

Remove the setting of WQID in the ABORT WQE.

Also cleaned up WQE field settings - initialize to zero, don't bother to
set fields to zero.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The current discovery state machine the driver treated FLOGI oddly.  When
point to point, an FLOGI is to be exchanged by the two ports, with the port
with the most significant WWN then proceeding with PLOGI.  The
implementation in the driver was keyed to closely with "what have I sent",
not with what has happened between the two endpoints. Thus, it blatantly
would ACC an FLOGI, but reject PLOGI's until it had its FLOGI ACC'd. The
problem is - the sending of FLOGI may be delayed for some reason, or the
response to FLOGI held off by the other side. In the failing situation the
other side sent an FLOGI, which was ACC'd, then sent PLOGIs which were then
rjt'd until the retry count for the PLOGIs were exceeded and the port gave
up. The FLOGI may have been very late in transmit, or the response held off
until the PLOGIs failed. Given the other port had the higher WWN, no PLOGIs
would occur and communication stopped.

Correct the situation by changing the FLOGI handling. Defer any response to
an FLOGI until the driver has sent its FLOGI as well. Then, upon either
completion of the sent FLOGI, or upon sending an ACC to a received FLOGI
(which may be received before or just after FLOGI was sent). the driver
will act on who has the higher WWN. if the other port does, the driver will
noop any handling of an FLOGI response (if outstanding) and wait for PLOGI.
If the local port does, the driver will transition to sending PLOGI and
will noop any action on responding to an FLOGI (if not yet received).

Fortunately, to implement this, it only took another state flag and
deferring any FLOGI response if the FLOGI has yet to be transmit. All
subsequent actions were already in place.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

In some link initialization sequences, the fw generates an erroneous FLOGI
payload to the driver without an intervening link bounce.  The driver, when
it sees a 2nd FLOGI without an intervening link bounce, automatically
performs a link bounce. In this, the link bounce causes the situate to
repeat and in a nasty loop of link bounces.

Resolve the issue by validating the FLOGI payload. The erroneous FLOGI will
contain VVL signatures that are not normal. When the driver sees these, it
will simply reject the flogi rather than bouncing the link.  The reject is
consumed within the firmware.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Two initiator ports were cable swapped and after swap both went down.  The
driver internally swaps the nlp nodes based on matching node wwn's but not
the same nport id as before. After detecting a change in the nodes RPI, the
driver sends an UNREG_RPI command and clears the NLP_RPI_REGISTERED flag,
then swaps the node information with the other node. But the other node's
NLP_RPI_REGISTERED flag is also cleared, but it is done so without an
UNREG_RPI being sent, which causes the later REG_RPI for that other node to
fail as the hardware believes its still registered.

Additionally, if the node swap occurred while the two nodes had PLOGI's in
flight, the fc4_types weren't properly getting swapped such that when the
PLOGIs commpleted and PRLI's were then sent, the PRLI's acted on bad
protocol types so the PRLI was for the wrong protocol. NVME devices saw
SCSI FCP PRLIs and vice versa.

Clean up the node swap so that the NLP_RPI_REGISTERED flag is handled
properly.

Fix the handling of the fc4_types when the nodes are swapped as well
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Depending on the chipset, the number of NPIV vports may vary and be in
excess of what most switches support (256). To avoid confusion with the
users, limit the reported NPIV vports to 256.

Additionally correct the 16G adapter which is reporting a bogus NPIV vport
number if the link is down.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Driver is hitting null pring pointers in lpfc_do_work().

Pointer assignment occurs based on SLI-revision. If recovering after an
error, its possible the sli revision for the port was cleared, making the
lpfc_phba_elsring() not return a ring pointer, thus the null pointer.

Add SLI revision checking to lpfc_phba_elsring() and status checking to all
callers.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Renumber one of the 0711 log messages so there isn't a duplication.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver is getting hit with 100s of RSCNs during remote port address
changes. Each of those RSCN's ends up generating UNREG_RPI and REG_PRI
mailbox commands.  The discovery engine within the driver doesn't wait for
the mailbox command completions. Instead it sets state flags and moves
forward. At some point, there's a massive backlog of mailbox commands which
take time for the adapter to process. Additionally, it appears there were
duplicate events from the switch so the driver generated duplicate mailbox
commands for the same remote port.  During this window, failures on PLOGI
and PRLI ELS's are see as the adapter is rejecting them as they are for
remote ports that still have pending mailbox commands.

Streamline the discovery engine so that PLOGI log checks for outstanding
UNREG_RPIs and defer the processing until the commands complete. This
better synchronizes the ELS transmission vs the RPI registrations.

Filter out multiple UNREG_RPIs being queued up for the same remote port.

Beef up log messages in this area.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver data structure for managing a mailbox command contained two
context fields. Unfortunately, the context were considered "generic" to be
used at the whim of the command code.  Of course, one section of code used
fields this way, while another did it that way, and eventually there were
mixups.

Refactored the structure so that the generic contexts become a node context
and a buffer context and all code standardizes on their use.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Update manufacturer attribute to reflect Broadcom Inc, not Emulex
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

While trying to get adapter fw-log for a function whose buffsize was set to
0, kernel panic occurred.

When buffsize is 0, the kernel buffer for the log won't be allocated.  When
fw log usage was enabled, it failed to check the buffer size, and log usage
was started. Eventually the driver referenced the unallocated log buffer.

Added checks of the buffer size before allowing fw logging to be enabled
and added check for valid buffer if enabling fw log.

Performed a couple other minor cleanups while fixing this:
 - clarified log messages
 - re-evaluated log message severity
 - treat any error as an error, not only a couple codes
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Since f44ac12f, BG enablement is tracked with the LPFC_SLI3_BG_ENABLED
bit, which is set in lpfc_get_cfgparam before lpfc_sli_config_sli_port() is
called. The bit shouldn't be cleared before checking the feature.  Based on
problem analysis by David Bond.

Fixes: f44ac12f "scsi: lpfc: Memory allocation error during driver start-up on power8"
Tested-by: NDavid Bond <dbond@suse.com>
Signed-off-by: NMartin Wilck <mwilck@suse.com>
Cc: stable@vger.kernel.org # 4.17.x
Cc: stable@vger.kernel.org # 4.18.x
Cc: stable@vger.kernel.org # 4.19.x
Reviewed-by: NHannes Reinecke <hare@suse.com>
Acked-by: NJames Smart <jsmart2021@gmail.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Replaced dma_alloc_coherent + memset with dma_zalloc_coherent.
Signed-off-by: NSabyasachi Gupta <sabyasachi.linux@gmail.com>
Acked-by: NJames Smart <james.smart@broadcom.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The driver currently uses pci_set_dma_mask despite otherwise using the
generic DMA API.  Switch it over to the better generic DMA API.
Signed-off-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This removes the legacy (non-mq) IO path for SCSI.

Cc: linux-scsi@vger.kernel.org
Acked-by: NHimanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Tested-by: NMing Lei <ming.lei@redhat.com>
Reviewed-by: NOmar Sandoval <osandov@fb.com>
Acked-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJens Axboe <axboe@kernel.dk>

Update the driver version to 12.0.0.8
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add trunking support to the driver. Trunking is found on more recent
asics. In general, trunking appears as a single "port" to the driver
and overall behavior doesn't differ. Link speed is reported as an
aggregate value, while link speed control is done on a per-physical
link basis with all links in the trunk symmetrical. Some commands
returning port information are updated to additionally provide
trunking information. And new ACQEs are generated to report physical
link events relative to the trunk.

This patch contains the following modifications:

- Added link speed settings of 128GB and 256GB.

- Added handling of trunk-related ACQEs, mainly logging and trapping
  of physical link statuses.

- Added additional bsg interface to query trunk state by applications.

- Augment link_state sysfs attribtute to display trunk link status
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The switches seem to respond faster to GID_PT vs GID_FT NameServer
queries.  Add support for GID_PT to be used over GID_FT to enable
faster storage failover detection. Includes addition of new module
parameter to select between GID_PT and GID_FT (GID_FT is default).
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

An address change for a remote port cause PRLI for the wrong protocol
to be sent.  The node copy done in the discovery code skipped copying
the fc4 protocols supported as well.

Fix the copy logic for the address change.  Beefed up log messages in
this area as well.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Testing a point-to-point topology and a case of re-FLOGI without
intervening link bouncing, showed an odd interaction with firmware and
a resulting scenario where the driver no longer probed after accepting
the new FLOGI.

Work around the firmware issue by issuing a link bounce if a FLOGI is
received after the link is already up and FLOGI's accepted.

While debugging the issue, realized that some debug traces should be
clarified to help in the future.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When LCB's are rejected, if beaconing was already in progress, the
Reason Code Explanation was not being set. Should have been set to
command in progress.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

On FCoE adapters, when running link bounce test in a loop, initiator
failed to login with switch switch and required driver reload to
recover. Switch reached a point where all subsequent FLOGIs would be
LS_RJT'd. Further testing showed the condition to be related to not
performing FCF discovery between FLOGI's.

Fix by monitoring FLOGI failures and once a repeated error is seen
repeat FCF discovery.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

This patch corrects two issues:

- An oops would occur if reading based on a non-zero offset.  Offset
  calculation was incorrect.

- Updates to ras config (logging level) were ignored if change was
  made while fw logging was enabled. Revise to dynamically update.
Signed-off-by: NDick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: NJames Smart <jsmart2021@gmail.com>
Reviewed-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>