- 23 5月, 2009 3 次提交
-
-
由 Mohamed Abbas 提交于
Periodic RX interrupt needed with ICT interrupt to prevent RX race. Sending RX interrupt require many steps to be done in the the device: 1- write interrupt to current index in ICT table. 2- dma RX frame. 3- update RX shared data to indicate last write index. 4- send interrupt. This could lead to RX race, driver could receive RX interrupt but the shared data changes does not reflect that. this could lead to RX race, RX periodic will solve this race Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohamed Abbas 提交于
Add ICT interrupt handler support, ICT should improve CPU utilization since it does not require target read which is very expensive. This interrupt handler only added to 5000 cards and newer. Device will write interrupts to ICT shared table to inform driver about its interrupts. These patches will not touch 3945 and 4965 interrupt handlers and tasklet. Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Mohamed Abbas 提交于
Add new lock to be used when accessing some registers. Also move the register lock and iwl_grab_nic_access inside the function for register access. This will prevent from forgetting to hold locks and nic access in the right way and make code easier to maintain. We over use the priv->lock spin lock and I guess we need to add new one for Tx queue after that we might need to change most of these lock to BH and just keep priv->lock as irq type. Signed-off-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 21 5月, 2009 2 次提交
-
-
由 Tomas Winkler 提交于
This patch replaces struct iwl3945_hw_key by struct iwl_hw_key. It's not used directly with any host command therefore removal is trivial Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Reinette Chatre 提交于
Calling cancel_delayed_work() from inside spin_lock_irqsave, introduces a potential deadlock. As explained by Johannes Berg <johannes@sipsolutions.net> A - lock T - timer phase CPU 1 CPU 2 --------------------------------------------- some place that calls cancel_timer_sync() (which is the | code) lock-irq(A) | "lock-irq"(T) | "unlock"(T) | wait(T) unlock(A) timer softirq "lock"(T) run(T) "unlock"(T) irq handler lock(A) unlock(A) Now all that again, interleaved, leading to deadlock: lock-irq(A) "lock"(T) run(T) IRQ during or maybe before run(T) --> lock(A) "lock-irq"(T) wait(T) We fix this by moving the call to cancel_delayed_work() into workqueue. There are cases where the work may not actually be queued or running at the time we are trying to cancel it, but cancel_delayed_work() is able to deal with this. Also cleanup iwl_set_mode related to this call. This function (iwl_set_mode) is only called when bringing interface up and there will thus not be any scanning done. No need to try to cancel scanning. Fixes http://bugzilla.kernel.org/show_bug.cgi?id=13224, which was also reported at http://marc.info/?l=linux-wireless&m=124081921903223&w=2 . Tested-by: NMiles Lane <miles.lane@gmail.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Acked-by: NZhu Yi <yi.zhu@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 12 5月, 2009 2 次提交
-
-
由 Johannes Berg 提交于
This removes all the dead code that tries to adjust the power saving level based on the system AC state (inacceptable policy in the kernel) or based on overtemp conditions (unused). Also, pass _all_ policy wrt. enabling PS to mac80211, since we do not use the power_disabled internally I now use that to mirror the mac80211 CONF_PS setting. When mac80211 turns off CONF_PS we follow suit. This means that the user power level (which can currently only be set from sysfs) is not touched for mac80211 powersave changes. This means no "association status" checks are necessary since mac80211 will not allow power save to be enabled when not associated. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Acked-by: NMohamed Abbas <mohamed.abbas@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
When the microcode fails for any reason, ask mac80211 to recover instead of trying ourselves and failing at it. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 07 5月, 2009 4 次提交
-
-
由 Greg Kroah-Hartman 提交于
In the near future, the driver core is going to not allow direct access to the driver_data pointer in struct device. Instead, the functions dev_get_drvdata() and dev_set_drvdata() should be used. These functions have been around since the beginning, so are backwards compatible with all older kernel versions. Cc: John W. Linville <linville@tuxdriver.com> Cc: linux-wireless@vger.kernel.org Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Patch seperates rx_used and rx_free into two different atomic contexts. We can now avoid using GFP_ATOMIC for skb allocation and use GFP_KERNEL. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
The config_interface method is a little strange, it contains the BSSID and beacon updates, while bss_info_changed contains most other BSS information for each interface. This patch removes config_interface and rolls all the information it previously passed to drivers into bss_info_changed. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
We currently have two beacon interval configuration knobs: hw.conf.beacon_int and vif.bss_info.beacon_int. This is rather confusing, even though the former is used when we beacon ourselves and the latter when we are associated to an AP. This just deprecates the hw.conf.beacon_int setting in favour of always using vif.bss_info.beacon_int. Since it touches all the beaconing IBSS code anyway, we can also add support for the cfg80211 IBSS beacon interval configuration easily. NOTE: The hw.conf.beacon_int setting is retained for now due to drivers still using it -- I couldn't untangle all drivers, some are updated in this patch. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 05 5月, 2009 1 次提交
-
-
由 Andreas Schwab 提交于
It does not make sense to apply EXPORT_SYMBOL to a static symbol. Fixes this build error: drivers/net/wireless/iwlwifi/iwl3945-base.c:1697: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict Signed-off-by: NAndreas Schwab <schwab@linux-m68k.org> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 29 4月, 2009 1 次提交
-
-
由 Stephen Rothwell 提交于
drivers/net/wireless/iwlwifi/iwl3945-base.c:1415: error: __ksymtab_iwl3945_rx_queue_reset causes a section type conflict I am pretty sure that this is a compiler bug, so not to worry. However, as far as I can see, iwl-3945.o (the only user) and iwl3945-base.o are always linked into the same module, so the EXPORT_SYMBOL (which causes the problem) should not be needed. Correct? Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 23 4月, 2009 23 次提交
-
-
由 Abhijeet Kolekar 提交于
Patch removes the "manual radio disable" parameter as there is no usage scenario of disabling radio using this module parameter. User can use iwconfig's txpower to enable and disable radio. This module parameter also does not work as expected. During module load the status of radio is set, the radio is not actually disabled. Even so, the moment mac80211 requests the interface to be up the radio will be enabled again. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
This patch clean up the code for NL80211_IFTYPE_MONITOR mode, priv->iw_mode is set in add_interface, but add_interface is never called for monitor mode. The only way mac80211 informs us about monitor mode is through configuring filter; since iw_mode will never set to NL80211_IFTYPE_MONITOR, modify and remove all the code refer to NL80211_IFTYPE_MONITOR and replace with iwl_is_monitor_mode() function call. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
This patch calculates interrupt statistics for debugfs. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Patch adds debugfs to 3945. Also fix debugfs registration in iwlagn to return error code if it fails. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
If passive scanning is requested we should not ask the microcode to do active scanning after detecting traffic on a channel -- that should only be used when an active scan is requested but some channels are marked passive. Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Johannes Berg 提交于
This modifies iwlwifi to * no longer build its own probe request, but use mac80211's * therefore, support arbitrary scan IEs (up to the max len) * support multiple scan SSIDs * support passive scanning Signed-off-by: NJohannes Berg <johannes@sipsolutions.net> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_reset_tsf from iwlwifi. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_get_tx_stats from iwlwifi. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_config_interface from iwlwifi. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
add config_ap lib op to iwlwifi and iwl3945 in preparation of future 3945 porting actions. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_config from iwlwifi Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_mac_remove_interface from iwlwifi Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can now use iwl_set_mode from iwlcore library. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
iwl3945 can now use iwl_get_sta_id. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Patch unifies the add_station function for 3945 and iwlwifi drivers. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Patch replaces station function used in driver by station management ops in 3945. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Delay mode setting till uCode is ready. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
Patch adds commit_rxon lib operation to iwlwifi and iwl3945 drivers. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can use iwl_mac_beacon_update. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 can use iwl_bss_info_changed. A new lib op is created for post_assoicate to distinguish between 3945 and iwlwifi's post_associate operations. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Abhijeet Kolekar 提交于
3945 now uses iwl_mac_conf_tx. Signed-off-by: NAbhijeet Kolekar <abhijeet.kolekar@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Wey-Yi Guy 提交于
With mac80211's help to call stop() and start() in mac80211 suspend/resume function, both iwlagn and iwl3945 no longer calling stop() and start(); remove un-necessary STATUS_IN_SUSPEND bit from both header files and functions, Move apm_ops.stop() function into pci_suspend() to ensure DMA is stopped before go into suspend mode. iwl3945 has the similar suspend/resume function as iwlagn, so move both functions to iwlcore to be shared by both drivers. Signed-off-by: NWey-Yi Guy <wey-yi.w.guy@intel.com> Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 22 4月, 2009 3 次提交
-
-
由 Reinette Chatre 提交于
A few issues wrt DMA were uncovered when using the driver with swiotlb. - driver should not use memory after it has been mapped - iwl3945's RX queue management cannot use all of iwlagn because the size of the RX buffer is different. Revert back to using iwl3945 specific routines that map/unmap memory. - no need to "dma_syn_single_range_for_cpu" followed by pci_unmap_single, we can just call pci_unmap_single initially - only map the memory area that will be used by device. this is especially relevant to the mapping of iwl_cmd. we should not map the entire structure because the meta data at the beginning of structure contains the address to be used later for unmapping. If the address to be used for unmapping is stored in mapped data it creates a problem. - ensure that _if_ memory needs to be modified after it is mapped that we call _sync_single_for_cpu first, and then release it back to device with _sync_single_for_device - we mapped the wrong length of data for host commands, with mapped length differing with length provided to device, fix that. Thanks to Jason Andryuk <jandryuk@gmail.com> for significant bisecting help to find these issues. This fixes http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1964Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Tested-by: NJason Andryuk <jandryuk@gmail.com> Tested-by: NBen Gamari <bgamari@gmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Reinette Chatre 提交于
When debugging TX issues it is helpful to know the seq nr of the frame being transmitted. The seq nr is printed as part of ucode's log informing us which frame is being processed. Having this information printed in driver log makes it easy to match activities between driver and firmware. Also make possible to print TX flags directly. These are already printed as part of entire TX command, but having it printed directly in cpu format makes it easier to look at. Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Reinette Chatre 提交于
Users reported lockup with work still trying to run after module has been unloaded. http://thread.gmane.org/gmane.linux.kernel.wireless.general/30594/focus=30601Signed-off-by: NReinette Chatre <reinette.chatre@intel.com> Reported-by: NTJ <ubuntu@tjworld.net> Reported-by: NHuaxu Wan <huaxu.wan@linux.intel.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
- 21 4月, 2009 1 次提交
-
-
由 Joe Perches 提交于
"not" is not printed without a space after %pM Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-