Under heavy traffic load, when changing number of channels via
ethtool (ethtool -L) which will cause interface to be reloaded,
it was observed that some packets gets transmitted on old TX
channel/queue id which doesn't really exist after the channel
configuration leads to system crash.

Add a safeguard in the driver by validating queue id through
ndo_select_queue() which is called before the ndo_start_xmit().
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Max supported queues is derived incorrectly in the case of multi-CoS.
Need to consider TCs while calculating num_queues for PF.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the case of Unified Fabric Port (UFP) mode, switch provides
the traffic class (TC) value to be used for the traffic.
Configure hardware to use this TC value for vlan priority.
Signed-off-by: NSudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When slowpath messages are sent with high rate, the resulting
events can lead to a FW assert in case they are not handled fast
enough (Event Queue Full assert). Attempt to send queued slowpath
messages only after the newly evacuated entries in the EQ ring
are indicated to FW.
Signed-off-by: NManish Chopra <manishc@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In packets that need to be decaped the internal headers
have to be checked, not the external ones.

Fixes: bdd66ac0 ("net/mlx5e: Disallow TC offloading of unsupported match/action combinations")
Signed-off-by: NGuy Shattah <sguy@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The match level computed by the driver gets to be wrong for decap
rules with wildcarded inner packet match such as:

tc filter add dev vxlan_sys_4789 protocol all parent ffff: prio 2 flower
       enc_dst_ip 192.168.0.9 enc_key_id 100 enc_dst_port 4789
       action tunnel_key unset
       action mirred egress redirect dev eth1

The FW errs for a missing matching meta-data indicator for the outer
headers (where we do have a match), and a wrong matching meta-data
indicator for the inner headers (where we don't have a match).

Fix that by taking into account the matching on the tunnel info and
relating the match level of the encapsulated packet to the firmware
inner headers indicator in case of decap.

As for vxlan we mandate a match on the tunnel udp dst port, and in general
we practically madndate a match on the source or dest ip for any IP tunnel,
the fix was done in a minimal manner around the tunnel match parsing code.

Fixes: d708f902 ('net/mlx5e: Get the required HW match level while parsing TC flow matches')
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NSlava Ovsiienko <viacheslavo@mellanox.com>
Reviewed-by: NJianbo Liu <jianbol@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

At Innova IPsec TX offload data path a special software parser metadata
is used to pass some packet attributes to the hardware, this metadata
is passed using the Ethernet control segment of a WQE (a HW descriptor)
header.

The cited commit might nullify this header, hence the metadata is lost,
this caused a significant performance drop during hw offloading
operation.

Fix by restoring the metadata at the Ethernet control segment in case
it was nullified.

Fixes: 37fdffb2 ("net/mlx5: WQ, fixes for fragmented WQ buffers API")
Signed-off-by: NRaed Salem <raeds@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Broadcom STB chips support a deep sleep mode where all register
contents are lost. Because we were stashing the MagicPacket password
into some of these registers a suspend into that deep sleep then a
resumption would not lead to being able to wake-up from MagicPacket with
password again.

Fix this by keeping a software copy of the password and program it
during suspend.

Fixes: 83e82f4c ("net: systemport: add Wake-on-LAN support")
Signed-off-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In case of IPv6 pkts, ipv4_csum_ok is 0. Because of this, driver does
not set skb->ip_summed. So IPv6 rx checksum is not offloaded.
Signed-off-by: NGovindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "p" buffer is 0x4000 bytes long.  B3_RI_WTO_R1 is 0x190.  The value
of "regs->len" is in the 1-0x4000 range.  The bug here is that
"regs->len - B3_RI_WTO_R1" can be a negative value which would lead to
memory corruption and an abrupt crash.

Fixes: c3f8be96 ("[PATCH] skge: expand ethtool debug register dump")
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When calling firmware to allocate a CP ring or NQ, an interrupt associated
with that ring may be generated immediately before the doorbell is even
setup after the firmware call returns.  When servicing the interrupt, the
driver may crash when trying to access the doorbell.

Fix it by disabling interrupt on that vector until the doorbell is
set up.

Fixes: 697197e5 ("bnxt_en: Re-structure doorbells.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In stmmac xmit callback we use a different flow for TSO packets but TSO
xmit callback is not disabling the EEE mode.

Fix this by disabling earlier the EEE mode, i.e. before calling the TSO
xmit callback.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The number of TSO enabled channels in HW can be different than the
number of total channels. There is no way to determined, at runtime, the
number of TSO capable channels and its safe to assume that if TSO is
enabled then at least channel 0 will be TSO capable.

Lets always send TSO packets from Queue 0.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we don't have DT then stmmac_clk will not be available. Let's add a
new Platform Data field so that we can specify the refclk by this mean.

This way we can still use the coalesce command in PCI based setups.
Signed-off-by: NJose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After a timeout event caused by for example a broadcast storm, when
the MAC and PHY are reset, the BQL TX queue needs to be reset as
well. Otherwise, the device will exhibit severe performance issues
even after the storm has ended.
Co-authored-by: NDavid Gounaris <david.gounaris@infinera.com>
Signed-off-by: NMathias Thore <mathias.thore@infinera.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The skb should be freed by dev_consume_skb_any() in b44_start_xmit()
when bounce_skb is used. The skb is be replaced by bounce_skb, so the
original skb should be consumed(not drop).

dev_consume_skb_irq() should be called in b44_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in cp_tx() when skb xmit
done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The interrupt handler contains a workaround for RX hang applicable
to Zynq and AT91RM9200 only. Subsequent versions do not need this
workaround. This workaround unnecessarily resets RX whenever RX used
bit read is observed, which can be often under heavy traffic. There
is no other action performed on RX UBR interrupt. Hence introduce a
CAPS mask; enable this interrupt and workaround only on affected
versions.
Signed-off-by: NHarini Katakam <harini.katakam@xilinx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in cpmac_end_xmit() when
xmit done. It makes drop profiles more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in bmac_txdma_intr() when
xmit done. It makes drop profiles more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in amd8111e_tx() when xmit
done. It makes drop profiles more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in ace_tx_int() when xmit
done. It makes drop profiles more friendly.
Signed-off-by: NYang Wei <yang.wei9@zte.com.cn>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

KASAN reported following bug in qed_init_qm_get_idx_from_flags
due to inappropriate casting of "pq_flags". Fix the type of "pq_flags".

[  196.624707] BUG: KASAN: stack-out-of-bounds in qed_init_qm_get_idx_from_flags+0x1a4/0x1b8 [qed]
[  196.624712] Read of size 8 at addr ffff809b00bc7360 by task kworker/0:9/1712
[  196.624714]
[  196.624720] CPU: 0 PID: 1712 Comm: kworker/0:9 Not tainted 4.18.0-60.el8.aarch64+debug #1
[  196.624723] Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL024 09/26/2018
[  196.624733] Workqueue: events work_for_cpu_fn
[  196.624738] Call trace:
[  196.624742]  dump_backtrace+0x0/0x2f8
[  196.624745]  show_stack+0x24/0x30
[  196.624749]  dump_stack+0xe0/0x11c
[  196.624755]  print_address_description+0x68/0x260
[  196.624759]  kasan_report+0x178/0x340
[  196.624762]  __asan_report_load_n_noabort+0x38/0x48
[  196.624786]  qed_init_qm_get_idx_from_flags+0x1a4/0x1b8 [qed]
[  196.624808]  qed_init_qm_info+0xec0/0x2200 [qed]
[  196.624830]  qed_resc_alloc+0x284/0x7e8 [qed]
[  196.624853]  qed_slowpath_start+0x6cc/0x1ae8 [qed]
[  196.624864]  __qede_probe.isra.10+0x1cc/0x12c0 [qede]
[  196.624874]  qede_probe+0x78/0xf0 [qede]
[  196.624879]  local_pci_probe+0xc4/0x180
[  196.624882]  work_for_cpu_fn+0x54/0x98
[  196.624885]  process_one_work+0x758/0x1900
[  196.624888]  worker_thread+0x4e0/0xd18
[  196.624892]  kthread+0x2c8/0x350
[  196.624897]  ret_from_fork+0x10/0x18
[  196.624899]
[  196.624902] Allocated by task 2:
[  196.624906]  kasan_kmalloc.part.1+0x40/0x108
[  196.624909]  kasan_kmalloc+0xb4/0xc8
[  196.624913]  kasan_slab_alloc+0x14/0x20
[  196.624916]  kmem_cache_alloc_node+0x1dc/0x480
[  196.624921]  copy_process.isra.1.part.2+0x1d8/0x4a98
[  196.624924]  _do_fork+0x150/0xfa0
[  196.624926]  kernel_thread+0x48/0x58
[  196.624930]  kthreadd+0x3a4/0x5a0
[  196.624932]  ret_from_fork+0x10/0x18
[  196.624934]
[  196.624937] Freed by task 0:
[  196.624938] (stack is not available)
[  196.624940]
[  196.624943] The buggy address belongs to the object at ffff809b00bc0000
[  196.624943]  which belongs to the cache thread_stack of size 32768
[  196.624946] The buggy address is located 29536 bytes inside of
[  196.624946]  32768-byte region [ffff809b00bc0000, ffff809b00bc8000)
[  196.624948] The buggy address belongs to the page:
[  196.624952] page:ffff7fe026c02e00 count:1 mapcount:0 mapping:ffff809b4001c000 index:0x0 compound_mapcount: 0
[  196.624960] flags: 0xfffff8000008100(slab|head)
[  196.624967] raw: 0fffff8000008100 dead000000000100 dead000000000200 ffff809b4001c000
[  196.624970] raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000
[  196.624973] page dumped because: kasan: bad access detected
[  196.624974]
[  196.624976] Memory state around the buggy address:
[  196.624980]  ffff809b00bc7200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  196.624983]  ffff809b00bc7280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  196.624985] >ffff809b00bc7300: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 04 f2 f2 f2
[  196.624988]                                                        ^
[  196.624990]  ffff809b00bc7380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  196.624993]  ffff809b00bc7400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[  196.624995] ==================================================================
Signed-off-by: NManish Chopra <manishc@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Cache number of fragments in the skb locally as in case
of linear skb (with zero fragments), tx completion
(or freeing of skb) may happen before driver tries
to get number of frgaments from the skb which could
lead to stale access to an already freed skb.
Signed-off-by: NManish Chopra <manishc@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VFs may hit VF-PF channel timeout while probing, as in some
cases it was observed that VF FLR and VF "acquire" message
transaction (i.e first message from VF to PF in VF's probe flow)
could occur simultaneously which could lead VF to fail sending
"acquire" message to PF as VF is marked disabled from HW perspective
due to FLR, which will result into channel timeout and VF probe failure.

In such cases, try retrying VF "acquire" message so that in later
attempts it could be successful to pass message to PF after the VF
FLR is completed and can be probed successfully.
Signed-off-by: NManish Chopra <manishc@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF is always configured to drop control frames
(with reserved mac addresses) but to work LACP
on the VFs, it would require LACP control frames
to be forwarded or transmitted successfully.

This patch fixes this in such a way that trusted VFs
(marked through ndo_set_vf_trust) would be allowed to
pass the control frames such as LACP pdus.
Signed-off-by: NManish Chopra <manishc@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When running tx switched traffic between VNICs
created via a bridge(to which VFs are added),
adapter drops the unicast packets in tx flow due to
VNIC's ucast mac being unknown to it. But VF interfaces
being in promiscuous mode should have caused adapter
to accept all the unknown ucast packets. Later, it
was found that driver doesn't really configure tx
promiscuous mode settings to accept all unknown unicast macs.

This patch fixes tx promiscuous mode settings to accept all
unknown/unmatched unicast macs and works out the scenario.
Signed-off-by: NManish Chopra <manishc@marvell.com>
Signed-off-by: NAriel Elior <aelior@marvell.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev_consume_skb_irq() should be called in i596_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <albin_yang@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If phy_power_on() fails in rk_gmac_powerup(), clocks are left enabled.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When reading phy registers via Clause 45 MDIO protocol, after write
address operation, the driver use another write address operation, so
can not read the right value of any phy registers. This patch fixes it.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hns driver of earlier devices, when autoneg off, restart autoneg
will return -EINVAL, so make the hns driver for the latest devices
do the same.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In hns enet driver, we use of_parse_handle() to get hold of the
device node related to "ae-handle" but we have missed to put
the node reference using of_node_put() after we are done using
the node. This patch fixes it.

Note:
This problem is stated in Link: https://lkml.org/lkml/2018/12/22/217

Fixes: 48189d6a ("net: hns: enet specifies a reference to dsaf")
Reported-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If fill_level was not zero and status was not BUSY,
result of "tx_prod - tx_cons - inuse" might be zero.
Subtracting 1 unconditionally results invalid negative return value
on this case.
Make sure not to return an negative value.
Signed-off-by: NTomonori Sakita <tomonori.sakita@sord.co.jp>
Signed-off-by: NAtsushi Nemoto <atsushi.nemoto@sord.co.jp>
Reviewed-by: NDalon L Westergreen <dalon.westergreen@linux.intel.com>
Acked-by: NThor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This is new code and not bug fixes.

This reverts all changes added by merge commit
8fb18be9Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It turns out that libvirt uses 0-vid as a default if no vlan was
set for the guest (which is the case for switchdev mode) and errs
if we disallow that:

error: Failed to start domain vm75
error: Cannot set interface MAC/vlanid to 6a:66:2d:48:92:c2/0 \
		for ifname enp59s0f0 vf 0: Operation not supported

So allow this in order not to break existing systems.
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NMaor Dickman <maord@mellanox.com>
Reviewed-by: NGavi Teitz <gavi@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

With VF LAG commit 491c37e4 "net/mlx5e: In case of LAG, one switch
parent id is used for all representors", both uplinks and all the VFs
(on both of them) get the same switchdev id.

This cause the provisioning system method to identify the rep of a given
VF from the parent PF PCI device using switchev id and physical port
name to break, since VFm of PF0 will have the (id, name) as VFm of PF1.

To fix that, we align to use the framework agreed upstream and set by
nfp commit 168c478e "nfp: wire get_phys_port_name on representors":

$ cat /sys/class/net/eth4_*/phys_port_name
p0
pf0vf0
pf0vf1

Now, the names will be different, e.g. pf0vf0 vs. pf1vf0.

Fixes: 491c37e4 ("net/mlx5e: In case of LAG, one switch parent id is used for all representors")
Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com>
Reported-by: NWaleed Musa <waleedm@mellanox.com>
Reviewed-by: NRoi Dayan <roid@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Prior to this patch the driver prohibited spoof checking on invalid MAC.
Now the user can set this configuration if it wishes to.

This is required since libvirt might invalidate the VF Mac by setting it
to zero, while spoofcheck is ON.

Fixes: 1ab2068a ("net/mlx5: Implement vports admin state backup/restore")
Signed-off-by: NAya Levin <ayal@mellanox.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

The lock in qp_table might be taken from process context or from
interrupt context. This may lead to a deadlock unless it is taken with
IRQs disabled.

Discovered by lockdep

================================
WARNING: inconsistent lock state
4.20.0-rc6
--------------------------------
inconsistent {HARDIRQ-ON-W} -> {IN-HARDIRQ-W}

python/12572 [HC1[1]:SC0[0]:HE0:SE1] takes:
00000000052a4df4 (&(&table->lock)->rlock#2){?.+.}, /0x50 [mlx5_core]
{HARDIRQ-ON-W} state was registered at:
  _raw_spin_lock+0x33/0x70
  mlx5_get_rsc+0x1a/0x50 [mlx5_core]
  mlx5_ib_eqe_pf_action+0x493/0x1be0 [mlx5_ib]
  process_one_work+0x90c/0x1820
  worker_thread+0x87/0xbb0
  kthread+0x320/0x3e0
  ret_from_fork+0x24/0x30
irq event stamp: 103928
hardirqs last  enabled at (103927): [] nk+0x1a/0x1c
hardirqs last disabled at (103928): [] unk+0x1a/0x1c
softirqs last  enabled at (103924): [] tcp_sendmsg+0x31/0x40
softirqs last disabled at (103922): [] 80

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&table->lock)->rlock#2);

    lock(&(&table->lock)->rlock#2);

 *** DEADLOCK ***

Fixes: 032080ab ("IB/mlx5: Lock QP during page fault handling")
Signed-off-by: NMoni Shoua <monis@mellanox.com>
Reviewed-by: NLeon Romanovsky <leonro@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

MLX5E_PFLAG_* definitions were changed from bitmask to enumerated
values. However, in mlx5e_open_rq(), the proper API (MLX5E_GET_PFLAG macro)
was not used to read the flag value of MLX5E_PFLAG_RX_NO_CSUM_COMPLETE.
Fixed it.

Fixes: 8ff57c18 ("net/mlx5e: Improve ethtool private-flags code structure")
Signed-off-by: NShay Agroskin <shayag@mellanox.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

This reverts commit 5f5991f3.

With the original commit, eswitch instance will not be initialized for
a function which is vport group manager but not eswitch manager such as
host PF on SmartNIC (BlueField) card. This will result in a kernel crash
when such a vport group manager is trying to access vports in its group.
E.g, PF vport manager (not eswitch manager) tries to configure the MAC
of its VF vport, a kernel trace will happen similar as bellow:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
 ...
 RIP: 0010:mlx5_eswitch_get_vport_config+0xc/0x180 [mlx5_core]
 ...

Fixes: 5f5991f3 ("net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager")
Signed-off-by: NBodong Wang <bodong@mellanox.com>
Reported-by: NYuval Avnery <yuvalav@mellanox.com>
Reviewed-by: NDaniel Jurgens <danielj@mellanox.com>
Reviewed-by: NOr Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>