Assemble all the API's to ease insertion of dump callbacks in the
following patches in the set.
Signed-off-by: NAya Levin <ayal@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

On driver load:
- Initialize resource dump data structure and memory access tools (mkey
  & pd).
- Read the resource dump's menu which contains the FW segment
  identifier. Each record is identified by the segment name (ASCII).

During the driver's course of life, users (like reporters) may request
dumps per segment. The user should create a command providing the
segment identifier (SW enumeration) and command keys. In return, the
user receives a command context. In order to receive the dump, the user
should supply the command context and a memory (aligned to a PAGE) on
which the dump content will be written. Since the dump may be larger
than the given memory, the user may resubmit the command until received
an indication of end-of-dump. It is the user's responsibility to destroy
the command.
Signed-off-by: NAya Levin <ayal@mellanox.com>
Reviewed-by: NMoshe Shemesh <moshe@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Add a new API for start/end binary array brackets [] to force array
around binary data as required from JSON. With this restriction, re-open
API to set binary fmsg data.
Signed-off-by: NAya Levin <ayal@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>

Instead of assigning skb = segments before the loop, just pass
 segments directly as the first argument to skb_list_walk_safe().
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After performing an unbind/bind operation the network is no longer
functional on i.MX6 (which has a single FEC instance):

# echo 2188000.ethernet > /sys/bus/platform/drivers/fec/unbind
# echo 2188000.ethernet > /sys/bus/platform/drivers/fec/bind
[   10.756519] pps pps0: new PPS source ptp0
[   10.792626] libphy: fec_enet_mii_bus: probed
[   10.799330] fec 2188000.ethernet eth0: registered PHC device 1
# udhcpc -i eth0
udhcpc: started, v1.31.1
[   14.985211] fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
[   14.993140] libphy: PHY fixed-0:00 not found
[   14.997643] fec 2188000.ethernet eth0: could not attach to PHY

On SoCs with two FEC instances there are some cases where one FEC instance
depends on the other one being present. One such example is i.MX28, which
has the following FEC dependency as noted in the comments:

	/*
	 * The i.MX28 dual fec interfaces are not equal.
	 * Here are the differences:
	 *
	 *  - fec0 supports MII & RMII modes while fec1 only supports RMII
	 *  - fec0 acts as the 1588 time master while fec1 is slave
	 *  - external phys can only be configured by fec0
	 *
	 * That is to say fec1 can not work independently. It only works
	 * when fec0 is working. The reason behind this design is that the
	 * second interface is added primarily for Switch mode.
	 *
	 * Because of the last point above, both phys are attached on fec0
	 * mdio interface in board design, and need to be configured by
	 * fec0 mii_bus.
	 */

Prevent the unbind operation to avoid these issues.
Signed-off-by: NFabio Estevam <festevam@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

drivers/net/ethernet/amazon/ena/ena_com.c: In function ena_com_hash_key_allocate:
drivers/net/ethernet/amazon/ena/ena_com.c:1070:50:
 warning: variable hash_key set but not used [-Wunused-but-set-variable]

commit 6a4f7dc8 ("net: ena: rss: do not allocate key when not supported")
introduced this, but not used, so remove it.
Reported-by: NHulk Robot <hulkci@huawei.com>
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The current codebase makes use of the zero-length array language
extension to the C90 standard, but the preferred mechanism to declare
variable-length types such as these ones is a flexible array member[1][2],
introduced in C99:

struct foo {
        int stuff;
        struct boo array[];
};

By making use of the mechanism above, we will get a compiler warning
in case the flexible array does not occur last in the structure, which
will help us prevent some kind of undefined behavior bugs from being
inadvertently introduced[3] to the codebase from now on.

Also, notice that, dynamic memory allocations won't be affected by
this change:

"Flexible array members have incomplete type, and so the sizeof operator
may not be applied. As a quirk of the original implementation of
zero-length arrays, sizeof evaluates to zero."[1]

This issue was found with the help of Coccinelle.

[1] https://gcc.gnu.org/onlinedocs/gcc/Zero-Length.html
[2] https://github.com/KSPP/linux/issues/21
[3] commit 76497732 ("cxgb3/l2t: Fix undefined behaviour")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now that the phylib module loading issue has been resolved, we can
allow this PHY driver to be built as a module.
Signed-off-by: NRussell King <rmk+kernel@armlinux.org.uk>
Acked-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ursula Braun says:

====================
net/smc: patches 2020-02-17

here are patches for SMC making termination tasks more perfect.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IB event handlers schedule the port event worker for further
processing of port state changes. This patch reduces the number of
schedules to avoid duplicate processing of the same port change.
Reviewed-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smc_lgr_terminate() and smc_lgr_terminate_sched() both result in soft
link termination, smc_lgr_terminate_sched() is scheduling a worker for
this task. Take out complexity by always using the termination worker
and getting rid of smc_lgr_terminate() completely.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The soft parameter of smc_lgr_terminate() is not used and obsolete.
Remove it.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When 2 callers call smc_lgr_terminate() at the same time
for the same lgr, one gets the lgr_lock and deletes the lgr from the
list and releases the lock. Then the second caller gets the lock and
tries to delete it again.
In smc_lgr_terminate() add a check if the link group lgr is already
deleted from the link group list and prevent to try to delete it a
second time.
And add a check if the lgr is marked as freeing, which means that a
termination is already pending.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smc_tx_rdma_write() is called under the send_lock and should not call
smc_lgr_terminate() directly. Call smc_lgr_terminate_sched() instead
which schedules a worker.
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

smc_lgr_cleanup() is called during termination processing, there is no
need to send a DELETE_LINK at that time. A DELETE_LINK should have been
sent before the termination is initiated, if needed.
And remove the extra call to wake_up(&lnk->wr_reg_wait) because
smc_llc_link_inactive() already calls the related helper function
smc_wr_wakeup_reg_wait().
Signed-off-by: NKarsten Graul <kgraul@linux.ibm.com>
Signed-off-by: NUrsula Braun <ubraun@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Ido Schimmel says:

====================
mlxsw: Reduce dependency between bridge and router code

This patch set reduces the dependency between the bridge and the router
code in preparation for RTNL removal from the route insertion path in
mlxsw.

The motivation and solution are explained in detail in patch #3. The
main idea is that we need to stop special-casing the VXLAN devices with
regards to the reference counting of the FIDs. Otherwise, we can bump
into the situation described in patch #3, where the routing code calls
into the bridge code which calls back into the routing code. After
adding a mutex to protect router data structures to remove RTNL
dependency, this can result in an AA deadlock.

Patches #1 and #2 are preparations. They convert the FIDs to use
'refcount_t' for reference counting in order to catch over/under flows
and add extack to the bridge creation function.

Patches #3-#5 reduce the dependency between the bridge and the router
code. First, by having the VXLAN device take a reference on the FID in
patch #3 and then by removing unnecessary code following the change in
patch #3.

Patches #6-#10 adjust existing selftests and add new ones to exercise
the new code paths.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test that when two VXLAN tunnels with conflicting configurations (i.e.,
different TTL) are enslaved to the same VLAN-aware bridge, then the
enslavement of a port to the bridge is denied.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After recent changes, the VXLAN tunnel will be offloaded regardless if
any local ports are member in the FID or not. Adjust the test to make
sure the tunnel is offloaded in this case.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The driver supports a single VLAN-aware bridge. Test that the
enslavement of a port to the second VLAN-aware bridge fails with an
extack.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Test that creation of a bridge (both VLAN-aware and VLAN-unaware) fails
with an extack when a VXLAN device with an unsupported configuration is
already enslaved to it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The addition of a VLAN on a bridge slave prompts the driver to have the
local port in question join the FID corresponding to this VLAN.

Before recent changes, the operation of joining the FID would also mean
that the driver would enable VXLAN tunneling if a VXLAN device was also
member in the VLAN. In case the configuration of the VXLAN tunnel was
not supported, an extack error would be returned.

Since the operation of joining the FID no longer means that VXLAN
tunneling is potentially enabled, the test is no longer relevant. Remove
it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit f40be47a ("mlxsw: spectrum_router: Do not force specific
configuration order") added a call from the routing code to the bridge
code in order to handle the case where VNI should be set on a FID
following the joining of the router port to the FID.

This is no longer required, as previous patches made VXLAN devices
explicitly take a reference on the FID and set VNI on it.

Therefore, remove the unnecessary call and simply have the RIF take a
reference on the FID without checking if VNI should also be set on it.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As explained in previous patch, VXLAN devices now take a reference on
the FID and not only local ports. Therefore, there is no need for local
ports to check if they need to set a VNI on the FID when they join the
FID.

Remove these unnecessary checks.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Up until now only local ports and the router port (which is also a local
port) took a reference on the corresponding FID (Filtering Identifier)
when joining a bridge. For example:

        192.0.2.1/24
            br0
             |
      +------+------+
      |             |
     swp1        vxlan0

In this case the reference count of the FID will be '2'. Since the VXLAN
device does not take a reference on the FID, whenever a local port joins
the bridge it needs to check if a VXLAN device is already enslaved. If
the VXLAN device should be mapped to the FID in question, then the VXLAN
device's VNI is set on the FID.

Beside the fact that this scheme special-cases the VXLAN device, it also
creates an unnecessary dependency between the routing and bridge code:

1. [R] IP address is added on 'br0', which prompts the creation of a RIF
   and a backing FID
2. [B] VNI is enabled on backing FID
3. [R] Host route corresponding to VXLAN device's source address is
   promoted to perform NVE decapsulation

[R] - Routing code
[B] - Bridge code

This back and forth dependency will become problematic when a lock is
added in the routing code instead of relying on RTNL, as it will result
in an AA deadlock.

Instead, have the VXLAN device take a reference on the FID just like all
the other netdev members of the bridge. In order to correctly handle the
case where VXLAN devices are already enslaved to the bridge when it is
offloaded, walk the bridge's slaves and replay the configuration.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Propagate extack to bridge creation function so that error messages
could be passed to user space via netlink instead of printing them to
kernel log.

A subsequent patch will pass the new extack argument to more functions.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

'refcount_t' is very useful for catching over/under flows. Convert the
FID (Filtering Identifier) objects to use it instead of 'unsigned int'
for their reference count.

A subsequent patch in the series will change the way VXLAN devices hold
/ release the FID reference, which is why the conversion is made now.
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This enables ndo_dflt_bridge_getlink() to report a bridge port's
offload settings for multicast and broadcast flooding.

CC: Roopa Prabhu <roopa@cumulusnetworks.com>
CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Edward Cree says:

====================
couple more ARFS tidy-ups

Tie up some loose ends from the recent ARFS work.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

efx_filter_rfs_expire() is a work-function, so it being inline makes no
 sense.  It's only ever used in efx_channels.c, so move it there.
While we're at it, clean out some related unused cruft.
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Prevent excessive CPU time spent running a workitem with nothing to do.

We avoid any races by keeping the same check in efx_filter_rfs_expire().
Suggested-by: NMartin Habets <mhabets@solarflare.com>
Signed-off-by: NEdward Cree <ecree@solarflare.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When a real dev unregisters, vlan_device_event() also unregisters all
of its vlan interfaces. For each VID this ends up in __vlan_vid_del(),
which attempts to remove the VID from the real dev's VLAN filter.

But the unregistering real dev might no longer be able to issue the
required IOs, and return an error. Subsequently we raise a noisy warning
msg that is not appropriate for this situation: the real dev is being
torn down anyway, there shouldn't be any worry about cleanly releasing
all of its HW-internal resources.

So to avoid scaring innocent users, suppress this warning when the
failed deletion happens on an unregistering device.
While at it also convert the raw pr_warn() to a more fitting
netdev_warn().
Signed-off-by: NJulian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since PCI core provides a generic PCI_DEVICE_DATA() macro,
replace STMMAC_DEVICE() with former one.

No functional change intended.
Signed-off-by: NAndy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vlad Buslov says:

====================
Remove rtnl lock dependency from flow_action infra

Currently, TC flow_action infrastructure code obtain rtnl lock before
accessing action state in tc_setup_flow_action() function and releases
it afterwards. This behavior is not supposed to impact TC filter
insertion rate because filling flow_action representation is only a
small part of creating new filter and expensive operations (hardware
offload callbacks, classifiers, cls API code that creates chains and
classifiers instances) already support unlocked execution. However,
typical vswitch implementation might need to also dump TC filters
concurrently, for example to age out unused flows or update flow
counters. TC dump is fully serialized and holds rtnl lock during its
whole execution in kernel space. As such, it can significantly impact
concurrent tasks that try to intermittently obtain rtnl lock when
filling intermediate representation for new filter offload (performance
evaluation at the end of this mail).

Refactor flow_action cls API infrastructure and its dependencies to not
rely on rtnl lock for synchronization. Patch set overview:

- Refactor tc_setup_flow_action() to obtain action tcf_lock when
  accessing action state. Fix its dependencies to not obtain tcf_lock
  themselves and assume that caller already holds it (needs to be done
  in same patch to prevent deadlock) and not to call sleeping functions
  (needs to be done in same patch to prevent "sleeping while atomic"
  dmesg warnings).

- Refactor action helper functions to require tcf_lock instead of rtnl.
  Internally, all of the actions already use tcf_lock for
  synchronization to accommodate unlocked classifier API, so this change
  relies on already existing functionality.

- Remove rtnl lock and "rtnl_held" argument from tc_setup_flow_action()
  function.

To test the change, multiple concurrent TC instances are invoked with
following command:

time ls add* | xargs -n 1 -P 100 sudo tc -b

Ten batch files with following typical rules (100k each) are used:

filter add dev ens1f0_0 protocol ip ingress prio 1 handle 1 flower
	src_mac e4:11:0:0:0:0 dst_mac e4:12:0:0:0:0 src_ip 192.168.111.1
	dst_ip 192.168.111.2 ip_proto udp dst_port 1 src_port 1 action
	tunnel_key set id 1 src_ip 2.2.2.2 dst_ip 2.2.2.3 dst_port 4789
	no_percpu action mirred egress redirect dev vxlan1 no_percpu

TC dump of same device is called in infinite loop from five concurrent
instances:

while true do tc -s filter show dev $NIC ingress >/dev/null done

Results obtained on current net-next commit 9f68e365 ("Merge tag
'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm"):

               | net-next | this change
---------------+----------+-------------
 TC add        | 6.3s     | 6.3s
 TC add + dump | 29.3s    | 6.8s

Test results confirm significant impact of concurrent TC dump. The
impact is almost fully mitigated by proposed change (differences can be
attributed to contention for chain and tp locks between add and dump TC
instances).
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Refactor tc_setup_flow_action() function not to use rtnl lock and remove
'rtnl_held' argument that is no longer needed.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to remove rtnl lock dependency from flow_action representation
translator, change rtnl_dereference() to rcu_dereference_protected() in ct
action helpers that provide external access to zone and action values. This
is safe to do because the functions are not called from anywhere else
outside flow_action infrastructure which was modified to obtain tcf_lock
when accessing action data in one of previous patches in the series.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to remove rtnl lock dependency from flow_action representation
translator, change rcu_dereference_bh_rtnl() to rcu_dereference_protected()
in police action helpers that provide external access to rate and burst
values. This is safe to do because the functions are not called from
anywhere else outside flow_action infrastructure which was modified to
obtain tcf_lock when accessing action data in one of previous patches in
the series.
Signed-off-by: NVlad Buslov <vladbu@mellanox.com>
Acked-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>