- 06 12月, 2008 1 次提交
-
- 05 12月, 2008 7 次提交
-
-
由 Shaddy Baddah 提交于
Under my 2.6.28-rc6 sparc64, when associating to an AP through my zd1211rw device, I was seeing kernel log messages like (not exact output): Kernel unaligned access at TPC[10129b68] zd_mac_rx+0x144/0x32c [zd1211rw] For the zd1211rw module, on RX, the 80211 packet will be located after the PLCP header in the skb data buffer. The PLCP header being 5 bytes long, the 80211 header will start unaligned from an aligned skb buffer. As per Documentation/unaligned-memory-access.txt, we must replace the not unaligned() safe compare_ether_addr() with memcmp() to protect architectures that require alignment. Signed-off-by: NShaddy Baddah <shaddy_baddah@hotmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Shaddy Baddah 提交于
After fixing zd1211rw: use unaligned safe memcmp() in-place of compare_ether_addr(), I started to see kernel log messages detailing unaligned access: Kernel unaligned access at TPC[100f7f44] sta_info_get+0x24/0x68 [mac80211] As with the aforementioned patch, the unaligned access was eminating from a compare_ether_addr() call. Concerned that whilst it was safe to assume that unalignment was the norm for the zd1211rw, and take preventative measures, it may not be the case or acceptable to use the easy fix of changing the call to memcmp(). My research however indicated that it was OK to do this, as there are a few instances where memcmp() is the preferred mechanism for doing mac address comparisons throughout the module. Signed-off-by: NShaddy Baddah <shaddy_baddah@hotmail.com> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Zhu Yi 提交于
In "ipw2200: Call netif_*_queue() interfaces properly", netif_stop_queue() and netif_wake_queue() were removed with the reason "netif_carrier_{on,off}() handles starting and stopping packet flow into the driver". The patch also removes a valid condition check that ipw_tx_skb() cannot be called if device is not in STATUS_ASSOCIATED state. But netif_carrier_off() doesn't guarantee netdev->hard_start_xmit won't be called because linkwatch event is handled in a delayed workqueue. This caused a kernel oops reported by Frank Seidel: https://bugzilla.novell.com/show_bug.cgi?id=397390 This patch fixes the problem by moving the STATUS_ASSOCIATED check back to ipw_tx_skb(). It also adds a missing netif_carrier_off() call to ipw_disassociate(). Signed-off-by: NZhu Yi <yi.zhu@intel.com> Signed-off-by: NChatre, Reinette <reinette.chatre@intel.com> Tested-by: NFrank Seidel <fseidel@suse.de> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Tomas Winkler 提交于
This patch cleans uCode key table bit map iwl_clear_stations_table since all stations are cleared also the key table must be. Since the keys are not removed properly on suspend by mac80211 this may result in exhausting key table on resume leading to memory corruption during removal This patch also fixes a memory corruption problem reported in http://marc.info/?l=linux-wireless&m=122641417231586&w=2 and tracked in http://bugzilla.kernel.org/show_bug.cgi?id=12040. When the key is removed a second time the offset is set to 255 - this index is not valid for the ucode_key_table and corrupts the eeprom pointer (which is 255 bits from ucode_key_table). Signed-off-by: NTomas Winkler <tomas.winkler@intel.com> Signed-off-by: NZhu Yi <yi.zhu@intel.com> Reported-by: NCarlos R. Mafra <crmafra2@gmail.com> Reported-by: NLukas Hejtmanek <xhejtman@ics.muni.cz> Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>
-
由 Doug Leith 提交于
This patch fixes a bug in tcp_vegas.c. At the moment this code leaves ssthresh untouched. However, this means that the vegas congestion control algorithm is effectively unable to reduce cwnd below the ssthresh value (if the vegas update lowers the cwnd below ssthresh, then slow start is activated to raise it back up). One example where this matters is when during slow start cwnd overshoots the link capacity and a flow then exits slow start with ssthresh set to a value above where congestion avoidance would like to adjust it. Signed-off-by: NDoug Leith <doug.leith@nuim.ie> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Oliver Hartkopp 提交于
Since commit d253eee2 the single CAN identifier filter lists handle only non-RTR CAN frames. So we need to omit the check of these filter lists when receiving RTR CAN frames. Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Chas Williams 提交于
As reported by Hugo Dias that it is possible to cause a local denial of service attack by calling the svc_listen function twice on the same socket and reading /proc/net/atm/*vc Signed-off-by: NChas Williams <chas@cmf.nrl.navy.mil> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 04 12月, 2008 7 次提交
-
-
由 Uwe Kleine-König 提交于
The spinlock used in the netx-eth driver was never properly initialized. This was noticed using CONFIG_DEBUG_SPINLOCK=y Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: NSascha Hauer <s.hauer@pengutronix.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Ilpo Järvinen 提交于
I should have noticed this earlier... :-) The previous solution to URG+GSO/TSO will cause SACK block tcp_fragment to do zig-zig patterns, or even worse, a steep downward slope into packet counting because each skb pcount would be truncated to pcount of 2 and then the following fragments of the later portion would restore the window again. Basically this reverts "tcp: Do not use TSO/GSO when there is urgent data" (33cf71ce). It also removes some unnecessary code from tcp_current_mss that didn't work as intented either (could be that something was changed down the road, or it might have been broken since the dawn of time) because it only works once urg is already written while this bug shows up starting from ~64k before the urg point. The retransmissions already are split to mss sized chunks, so only new data sending paths need splitting in case they have a segment otherwise suitable for gso/tso. The actually check can be improved to be more narrow but since this is late -rc already, I'll postpone thinking the more fine-grained things. Signed-off-by: NIlpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Baruch Siach 提交于
Packet data read from the RX buffer the when the RSV is at the end of the RX buffer does not warp around. This causes packet loss, as the actual data is never read. Fix this by calculating the right packet data location. Thanks to Shachar Shemesh for suggesting the fix. Signed-off-by: NBaruch Siach <baruch@tkos.co.il> Acked-by: NClaudio Lanconelli <lanconelli.claudio@eptar.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Pascal Terjan 提交于
ifa_local is assumed to be unsigned long which lead to writing the address at dev->dev_addr-2 instead of +2 noticed thanks to gcc: drivers/isdn/hysdn/hysdn_net.c: In function `net_open': drivers/isdn/hysdn/hysdn_net.c:91: warning: array subscript is below array bounds Signed-off-by: NPascal Terjan <pterjan@mandriva.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wilfried Klaebe 提交于
On "/etc/init.d/capiutils stop", this oops happened. The oops happens on reading /proc/capi/controllers because capi_ctrl->procinfo is called for the wrongly not unregistered controller, which points to b1isa_procinfo(), which was removed on module unload. b1isa_exit() did not call b1isa_remove() for its controllers because io[0] == 0 on module unload despite having been 0x340 on module load. Besides, just removing the controllers that where added on module load time and not those that were added later via b1isa_add_card() is wrong too - the place where all added cards are found is isa_dev[]. relevant dmesg lines: [ 0.000000] Linux version 2.6.27.4 (w@shubashi) (gcc version 4.3.2 (Debian 4.3.2-1) ) #3 Thu Oct 30 16:49:03 CET 2008 [ 67.403555] CAPI Subsystem Rev 1.1.2.8 [ 68.529154] capifs: Rev 1.1.2.3 [ 68.563292] capi20: Rev 1.1.2.7: started up with major 68 (middleware+capifs) [ 77.026936] b1: revision 1.1.2.2 [ 77.049992] b1isa: revision 1.1.2.3 [ 77.722655] kcapi: Controller [001]: b1isa-340 attached [ 77.722671] b1isa: AVM B1 ISA at i/o 0x340, irq 5, revision 255 [ 81.272669] b1isa-340: card 1 "B1" ready. [ 81.272683] b1isa-340: card 1 Protocol: DSS1 [ 81.272689] b1isa-340: card 1 Linetype: point to multipoint [ 81.272695] b1isa-340: B1-card (3.11-03) now active [ 81.272702] kcapi: card [001] "b1isa-340" ready. [ 153.721281] kcapi: card [001] down. [ 154.151889] BUG: unable to handle kernel paging request at e87af000 [ 154.152081] IP: [<e87af000>] [ 154.153292] *pde = 2655b067 *pte = 00000000 [ 154.153307] Oops: 0000 [#1] [ 154.153360] Modules linked in: rfcomm l2cap ppdev lp ipt_MASQUERADE tun capi capifs kernelcapi ac battery nfsd exportfs nfs lockd nfs_acl sunrpc sit tunnel4 bridge stp llc ipt_REJECT ipt_LOG xt_tcpudp xt_state iptable_filter iptable_mangle iptable_nat nf_nat nf_conntrack_ipv4 nf_conntrack ip_tables x_tables nls_utf8 isofs nls_base zlib_inflate loop ipv6 netconsole snd_via82xx dvb_usb_dib0700 gameport dib7000p dib7000m dvb_usb snd_ac97_codec ac97_bus dvb_core mt2266 snd_pcm tuner_xc2028 dib3000mc dibx000_common mt2060 dib0070 snd_page_alloc snd_mpu401_uart snd_seq_midi snd_seq_midi_event btusb snd_rawmidi bluetooth snd_seq snd_timer snd_seq_device snd via686a i2c_viapro soundcore i2c_core parport_pc parport button dm_mirror dm_log dm_snapshot floppy sg ohci1394 uhci_hcd ehci_hcd 8139too mii ieee1394 usbcore sr_mod cdrom sd_mod thermal processor fan [last unloaded: b1] [ 154.153360] [ 154.153360] Pid: 4132, comm: capiinit Not tainted (2.6.27.4 #3) [ 154.153360] EIP: 0060:[<e87af000>] EFLAGS: 00010286 CPU: 0 [ 154.153360] EIP is at 0xe87af000 [ 154.153360] EAX: e6b9ccc8 EBX: e6b9ccc8 ECX: e87a0c67 EDX: e87af000 [ 154.153360] ESI: e142bbc0 EDI: e87a56e0 EBP: e0505f0c ESP: e0505ee4 [ 154.153360] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 0068 [ 154.153360] Process capiinit (pid: 4132, ti=e0504000 task=d1196cf0 task.ti=e0504000) [ 154.153360] Stack: e879f650 00000246 e0505ef4 c01472eb e0505f0c 00000246 e7001780 fffffff4 [ 154.153360] fffffff4 e142bbc0 e0505f48 c01a56c6 00000400 b805e000 d102dc80 e142bbe0 [ 154.153360] 00000000 e87a56e0 00000246 e12617ac 00000000 00000000 e1261760 fffffffb [ 154.153360] Call Trace: [ 154.153360] [<e879f650>] ? controller_show+0x20/0x90 [kernelcapi] [ 154.153360] [<c01472eb>] ? trace_hardirqs_on+0xb/0x10 [ 154.153360] [<c01a56c6>] ? seq_read+0x126/0x2f0 [ 154.153360] [<c01a55a0>] ? seq_read+0x0/0x2f0 [ 154.153360] [<c01c033c>] ? proc_reg_read+0x5c/0x90 [ 154.153360] [<c0189919>] ? vfs_read+0x99/0x140 [ 154.153360] [<c01c02e0>] ? proc_reg_read+0x0/0x90 [ 154.153360] [<c0189a7d>] ? sys_read+0x3d/0x70 [ 154.153360] [<c0103c3d>] ? sysenter_do_call+0x12/0x35 [ 154.153360] ======================= [ 154.153360] Code: Bad EIP value. [ 154.153360] EIP: [<e87af000>] 0xe87af000 SS:ESP 0068:e0505ee4 [ 154.153360] ---[ end trace 23750b6c2862de94 ]--- Signed-off-by: NWilfried Klaebe <linux-kernel@lebenslange-mailadresse.de> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Acked-by: NKarsten Keil <kkeil@suse.de> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Oliver Hartkopp 提交于
Due to a wrong safety check in af_can.c it was not possible to filter for SFF frames with a specific CAN identifier without getting the same selected CAN identifier from a received EFF frame also. This fix has a minimum (but user visible) impact on the CAN filter API and therefore the CAN version is set to a new date. Indeed the 'old' API is still working as-is. But when now setting CAN_(EFF|RTR)_FLAG in can_filter.can_mask you might get less traffic than before - but still the stuff that you expected to get for your defined filter ... Thanks to Kurt Van Dijck for pointing at this issue and for the review. Signed-off-by: NOliver Hartkopp <oliver@hartkopp.net> Acked-by: NKurt Van Dijck <kurt.van.dijck@eia.be> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
Signed-off-by: NRémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 03 12月, 2008 25 次提交
-
-
由 Paul Moore 提交于
Fix a potential NULL pointer dereference seen when trying to remove a static label configuration with an invalid address/mask combination. Signed-off-by: NPaul Moore <paul.moore@hp.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Michael Chan 提交于
The bnx2 chips do not support per MSI vector masking. On 5706/5708, new MSI address/data are stored only when the MSI enable bit is toggled. As a result, SMP affinity no longer works in the latest kernel. A more serious problem is that the driver will no longer receive interrupts when the MSI receiving CPU goes offline. The workaround in this patch only addresses the problem of CPU going offline. When that happens, the driver's timer function will detect that it is making no forward progress on pending interrupt events and will recover from it. Eric Dumazet reported the problem. We also found that if an interrupt is internally asserted while MSI and INTA are disabled, the chip will end up in the same state after MSI is re-enabled. The same workaround is needed for this problem. Signed-off-by: NMichael Chan <mchan@broadcom.com> Tested-by: NEric Dumazet <dada1@cosmosbay.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Wei Yongjun 提交于
After flush the SPD entries, dump the SPD entries will cause kernel painc. Used the following commands to reproduct: - echo 'spdflush;' | setkey -c - echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64 any -P out ipsec \ ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\ spddump;' | setkey -c - echo 'spdflush; spddump;' | setkey -c - echo 'spdadd 3ffe:501:ffff:ff01::/64 3ffe:501:ffff:ff04::/64 any -P out ipsec \ ah/tunnel/3ffe:501:ffff:ff00:200:ff:fe00:b0b0-3ffe:501:ffff:ff02:200:ff:fe00:a1a1/require;\ spddump;' | setkey -c This is because when flush the SPD entries, the SPD entry is not remove from the list. This patch fix the problem by remove the SPD entry from the list. Signed-off-by: NWei Yongjun <yjwei@cn.fujitsu.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/wim/linux-2.6-watchdog: [WATCHDOG] hpwdt: Fix kdump when using hpwdt [WATCHDOG] hpwdt: set the mapped BIOS address space as executable [WATCHDOG] iTCO_wdt: add PCI ID's for ICH9 & ICH10 chipsets [WATCHDOG] iTCO_wdt : correct status clearing [WATCHDOG] iTCO_wdt : problem with rebooting on new ICH9 based motherboards [WATCHDOG] fix mtx1_wdt compilation failure
-
git://git.infradead.org/ubifs-2.6由 Linus Torvalds 提交于
* 'linux-next' of git://git.infradead.org/ubifs-2.6: UBIFS: pre-allocate bulk-read buffer UBIFS: do not allocate too much UBIFS: do not print scary memory allocation warnings UBIFS: allow for gaps when dirtying the LPT UBIFS: fix compilation warnings MAINTAINERS: change UBI/UBIFS git tree URLs UBIFS: endian handling fixes and annotations UBIFS: remove printk
-
git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm由 Linus Torvalds 提交于
* 'kvm-updates/2.6.28' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm: KVM: MMU: avoid creation of unreachable pages in the shadow KVM: ppc: stop leaking host memory on VM exit KVM: MMU: fix sync of ptes addressed at owner pagetable KVM: ia64: Fix: Use correct calling convention for PAL_VPS_RESUME_HANDLER KVM: ia64: Fix incorrect kbuild CFLAGS override KVM: VMX: Fix interrupt loss during race with NMI KVM: s390: Fix problem state handling in guest sigp handler
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6: sparc64: Fix offset calculation in compute_size() rtc: rtc-starfire fixes
-
git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (30 commits) MAINTAINERS: add netdev to ATM ATM: horizon, fix hrz_probe fail path pppol2tp: Add missing sock_put() in pppol2tp_release() net: Fix soft lockups/OOM issues w/ unix garbage collector macvlan: don't broadcast PAUSE frames to macvlan devices Phonet: fix oops in phonet_address_del() on non-Phonet device netfilter: ctnetlink: fix GFP_KERNEL allocation under spinlock sungem: Fix PCS_MIICTRL register write in gem_init_phy(). net: make skb_truesize_bug() call WARN() net: hp-plus uses eip_poll net/wireless/reg.c: fix bad WARN_ON in if statement ath5k: disable beacon filter when station is not associated ath5k: fix Security issue in DebugFS part of ath5k ath9k: correct expected max RX buffer size ath9k: Fix SW-IOMMU bounce buffer starvation mac80211 : Fix setting ad-hoc mode and non-ibss channel iwlagn: fix DMA sync phylib: Add Vitesse VSC8221 SGMII PHY rose: zero length frame filtering in af_rose.c bridge: netfilter: fix update_pmtu crash with GRE ...
-
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k由 Linus Torvalds 提交于
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k: m68k: Update defconfigs for 2.6.28-rc7 macfb: Do not overflow fb_fix_screeninfo.id
-
git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/bart/ide-2.6: alim15x3: fix sparse warning ide: remove dead code from drive_is_ready() ide: fix build for DEBUG_PM ide: respect current DMA setting during resume ide: add SAMSUNG SP0822N with firmware WA100-10 to ivb_list[] amd74xx: workaround unreliable AltStatus register for nVidia controllers ide: fix the ide_release_lock imbalance
-
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6由 Linus Torvalds 提交于
* git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6: [SCSI] stex: switch to block timeout [SCSI] make scsi_eh_try_stu use block timeout [SCSI] megaraid_sas: switch to block timeout [SCSI] ibmvscsi: switch to block timeout [SCSI] aacraid: switch to block timeout [SCSI] zfcp: prevent double decrement on host_busy while being busy [SCSI] zfcp: fix deadlock between wq triggered port scan and ERP [SCSI] zfcp: eliminate race between validation and locking [SCSI] zfcp: verify for correct rport state before scanning for SCSI devs [SCSI] zfcp: returning an ERR_PTR where a NULL value is expected [SCSI] zfcp: Fix opening of wka ports [SCSI] zfcp: fix remote port status check [SCSI] fc_transport: fix old bug on bitflag definitions [SCSI] Fix hang in starved list processing
-
由 Mark Salter 提交于
This fixes the MN10300 kernel module linking to match the toolchain. RELA relocs don't use the value at the location being relocated. This has been working because the tools always leave the value at the target location cleared. Signed-off-by: NMark Salter <msalter@redhat.com> Signed-off-by: NDavid Howells <dhowells@redhat.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Dean Nelson 提交于
If xpc.ko and gru.ko are both statically linked into the kernel, then xpc_init() can get called before gru_init() and make a call to one of the gru's exported functions before the gru has initialized itself. The end result is a NULL dereference. Signed-off-by: NDean Nelson <dcn@sgi.com> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Kumar Gala 提交于
In the CONFIG_SMP case the irq_choose_cpu() code was returning back a logical cpu id not the physical id. We were writing that directly into the HW register. We need to be calling get_hard_smp_processor_id() so irq_choose_cpu() always returns a physical cpu id. Signed-off-by: NKumar Gala <galak@kernel.crashing.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Rik van Riel 提交于
Count the insertion of new pages in the statistics used to drive the pageout scanning code. This should help the kernel quickly evict streaming file IO. We count on the fact that new file pages start on the inactive file LRU and new anonymous pages start on the active anon list. This means streaming file IO will increment the recent scanned file statistic, while leaving the recent rotated file statistic alone, driving pageout scanning to the file LRUs. Pageout activity does its own list manipulation. Signed-off-by: NRik van Riel <riel@redhat.com> Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com> Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com> Tested-by: NGene Heskett <gene.heskett@gmail.com> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Kay Sievers 提交于
Devices which share the same queue, like floppies and mtd devices, get registered multiple times in the bdi interface, but bdi accounts only the last registered device of the devices sharing one queue. On remove, all earlier registered devices leak, stay around in sysfs, and cause "duplicate filename" errors if the devices are re-created. This prevents the creation of multiple bdi interfaces per queue, and the bdi device will carry the dev_t name of the block device which is the first one registered, of the pool of devices using the same queue. [akpm@linux-foundation.org: add a WARN_ON so we know which drivers are misbehaving] Tested-by: NPeter Korsgaard <jacmet@sunsite.dk> Acked-by: NPeter Zijlstra <a.p.zijlstra@chello.nl> Signed-off-by: NKay Sievers <kay.sievers@vrfy.org> Cc: David Woodhouse <dwmw2@infradead.org> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Junjiro R. Okajima 提交于
The previous patch from Alan Cox ("nfsd: fix vm overcommit crash", commit 731572d3) fixed the problem where knfsd crashes on exported shmemfs objects and strict overcommit is set. But the patch forgot supporting the case when CONFIG_SECURITY is disabled. This patch copies a part of his fix which is mainly for detecting a bug earlier. Acked-by: NJames Morris <jmorris@namei.org> Signed-off-by: NAlan Cox <alan@redhat.com> Signed-off-by: NJunjiro R. Okajima <hooanon05@yahoo.co.jp> Signed-off-by: NAndrew Morton <akpm@linux-foundation.org> Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
-
由 Geert Uytterhoeven 提交于
Signed-off-by: NGeert Uytterhoeven <geert@linux-m68k.org>
-
由 Hannes Eder 提交于
Fix this sparse warning: drivers/ide/alim15x3.c:594:2: warning: returning void-valued expression Signed-off-by: NHannes Eder <hannes@hanneseder.net> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
We guarantee 400ns delay at the time of issuing the command. Acked-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Also while at it: * Drop unused arguments from ide_complete_power_step(). * Move DEBUG_PM printk() from ide_end_drive_cmd() to ide_complete_power_step(). Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Respect current DMA setting during resume, otherwise PIO timings may get destroyed if host uses shared PIO/MWDMA timings. Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
Should fix kernel.org bug #10225: http://bugzilla.kernel.org/show_bug.cgi?id=10225Reported-by: NMatthias B. <haferfrost@web.de> Cc: Alan Cox <alan@lxorguk.ukuu.org.uk> Acked-by: NSergei Shtyltov <sshtylyov@ru.mvista.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
It seems that on some nVidia controllers using AltStatus register can be unreliable so default to Status register if the PCI device is in Compatibility Mode. In order to achieve this: * Add ide_pci_is_in_compatibility_mode() inline helper to <linux/ide.h>. * Add IDE_HFLAG_BROKEN_ALTSTATUS host flag and set it in amd74xx host driver for nVidia controllers in Compatibility Mode. * Teach actual_try_to_identify() and drive_is_ready() about the new flag. This fixes the regression caused by removal of CONFIG_IDEPCI_SHARE_IRQ config option in 2.6.25 and using AltStatus register unconditionally when available (kernel.org bugs #11659 and #10216). [ Moreover for CONFIG_IDEPCI_SHARE_IRQ=y (which is what most people and distributions use) it never worked correctly. ] Thanks to Remy LABENE and Lars Winterfeld for help with debugging the problem. More info at: http://bugzilla.kernel.org/show_bug.cgi?id=11659 http://bugzilla.kernel.org/show_bug.cgi?id=10216Reported-by: NRemy LABENE <remy.labene@free.fr> Tested-by: NRemy LABENE <remy.labene@free.fr> Tested-by: NLars Winterfeld <lars.winterfeld@tu-ilmenau.de> Acked-by: NBorislav Petkov <petkovbb@gmail.com> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-
由 Michael Schmitz 提交于
ide_release_lock() spits out lots of: ide_release_lock: bug warnings on Atari Falcon. Fix the ide_release_lock imbalance. Signed-off-by: NMichael Schmitz <schmitz@biophys.uni-duesseldorf.de> Cc: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: NBartlomiej Zolnierkiewicz <bzolnier@gmail.com>
-