On some SoCs, the USB controller registers and descriptors can be big
or little endian, depending on the version of the chip. In order to be
able to run the same kernel binary on different versions of an SoC, the
BE/LE decision must be made at run time. Provide appropriate register
and descriptor accessors which are configurable at run time using the
configuration flags from fsl_usb2_platform_data data structure.

This is in preparation for adding support for MPC5121E DR USB2 Controller
to the FSL UDC driver.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Cc: Li Yang <leoli@freescale.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

When only FSL USB gadget driver is selected in the kernel
configuration the MPH DR OF driver for creation of FSL
USB platform devices from device tree won't be built.
As a result no USB platform devices for MPH DR USB controller
will be created at run time and no probing will be done in
the fsl_udc_core driver.

Add an entry to the Makefile to build the MPH DR OF
platform driver if CONFIG_USB_FSL_MPH_DR_OF is defined.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Provide common otg_state_string() and use
it in drivers.
Signed-off-by: NAnatolij Gustschin <agust@denx.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

dummy_hcd + g_zero:

|./testusb -a -s 1024 -v 1024 -t 10
| usbtest 2-1:3.0: subtest 14 error, status 0

with patch:
  ./testusb -a -t 10
|unknown speed   /proc/bus/usb/001/002
| dummy_udc dummy_udc: disabled ep-a
| dummy_udc dummy_udc: disabled ep-b
| dummy_udc dummy_udc: enabled ep-a (ep1in-bulk) maxpacket 1024
| dummy_udc dummy_udc: enabled ep-b (ep2out-bulk) maxpacket 1024
| zero gadget: source/sink enabled
| usbtest 1-1:3.0: TEST 10:  queue 32 control calls, 1000 times
| dummy_hcd dummy_hcd: timer fired with no URBs pending?
|/proc/bus/usb/001/002 test 10,    0.022370 secs
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit b02d0ed6 ('xhci: Change
hcd_priv into a pointer') added calls to kzalloc() and kfree() in
xhci-pci.c.  On most architectures <linux/slab.h> is indirectly
included, but on some it is not.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: Sarah Sharp <sarah.a.sharp@linux.intel.com>,
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The usb_create_sysfs_intf_files() function always returned zero even
if it failed to create sysfs fails.  Since this is a desired behaviour
there is no need to return return code at all.  This commit changes
function's return type (form int) to void.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1452b) adds a new test case to the usbtest driver.  Test
24 exercises the unlink-from-queue pathways in the host.  It queues a
user-specified number of bulk-OUT URBs of user-specified size, unlinks
the fourth- and second-from-last URBs in the queue, and then waits to
see if all the URBs complete in the expected way (except of course
that the unlinked URBs might complete normally, if they weren't
unlinked soon enough).

This new test has confirmed the existence of a bug in the ehci-hcd
driver, to be fixed by a separate patch.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Tegra USB1 port needs to issue Port Reset twice internally, otherwise it
fails to enumerate devices attached to it
Signed-off-by: NJim Lin <jilin@nvidia.com>
Signed-off-by: NOlof Johansson <olofj@chromium.org>
[ squash two patches into one and minor style cleanups ]
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch uses the resource_size help function instead of
manually calculating the resource size. It can reduce the chance
of introducing off-by-one errors.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The __devinit and __devexit macros were added to probe and remove
functions. The macros move the probe and remove functions to the
devinit and devexit sections.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This commit fixes an embarrassing bug in the "storage_common:
use kstrto*()" patch which caused fsg_store_ro() to return
zero instead of the length of the consumed buffer.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

the_controller is allocated in dummy_hcd_probe() and is NULL if the
allocation failed. The probe function of the udc driver is dereferencing
this pointer and fault.
Alan Stern suggested to abort the dummy_hcd driver probing so the module
is not loaded. The is abort-on-error has been also added to the udc
driver.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

If USB type detections fails, we run into default and return 0.
Signed-off-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current renesas_usbhs was designed to save power when USB is not connected.
And it assumed platform uses callback to notify connection/disconnection
by external interrupt.

But some SuperH / platform board doesn't have such feature.

This patch adds autonomy mode which detect USB connection/disconnection
by internal interrupt.
But power will be always ON when autonomy mode is selected.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This delay is used to overjump debounce.

And, this patch also move usbhsc_drvcllbck_notify_hotplug to global,
because it will be called from other files.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usbhs_status_get_each_irq/usbhs_irq_callback_update might be called
with mod == NULL
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

usbhs_pdev_to_priv function will be used in other files.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The callback function which is called from platform must be removed
if module removed.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

There are some USB Host which doesn't notice disconnection at once.
And it might try some request after reconnection with old settings.
Current renesas_usbhs will crash in such case.
This patch prevent this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current renesas_usbhs driver was using spin_trylock to avoid
dead lock / nest lock.
But acording to CONFIG_DEBUG_SPINLOCK, it is BUG under UP environment.
This patch add usbhsg_trylock to avoid this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Because pipe buffer allocation is very picky and difficult,
current renesas_usbhs driver is not caring pipe re-allocation.

In this situation, driver will create new pipe without caring old pipe
if "usbhsg_ep_enable" is called after "usbhsg_ep_disable" on current driver.
This mean the limited pipe and buffer will be used as waste.
But it is possible to re-use same buffer to same pipe.

By this patch, driver will initialize pipe when it detected new connection or
new gadget, and doesn't try re-allocation for same pipe in above case.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Pipe buffer should be cleaned before using it,
but should NOT be cleaned in pipe "prepare" function.
Because the pipe might be working in such timing.
This patch fixup this issue.
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

g_printer reqiured "set interface" request from host. Not all hosts send
this request.  This patch enable the interface when it get "set
configuration" request from host.
Signed-off-by: NJonas Andersson <jonas@microbit.se>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Stripping the direction bit off will produce an
invalid descriptor.
Signed-off-by: NSven Schnelle <svens@stackframe.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

The current code doesn't set it, so linux complains about
it when connected, and ignores the device:

[104611.068082] usb 1-5: new high speed USB device using ehci_hcd and address 127
[104611.088368] usb 1-5: Invalid ep0 maxpacket: 0
Signed-off-by: NSven Schnelle <svens@stackframe.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Current code returns 0 even if it can't handle the request.
This leads to timeouts when an unhandled request is sent:

Bus 001 Device 003: ID 0525:c0de Netchip Technology, Inc.
Device Descriptor:
[..]
can't get device qualifier: Connection timed out
[..]

change the code to return EOPNOTSUPP in such cases.
Signed-off-by: NSven Schnelle <svens@stackframe.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixup cast warning on 64 bit compiler
Signed-off-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reported-by: NGreg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch (as1459) updates the documentation for the pre_reset method
in struct usb_driver.  When a driver is notified of an impending
reset, it must cancel all outstanding I/O and not start any new I/O
until it has been notified that the reset is complete.

As far as I know, most existing drivers that implement pre_reset do
this now.  The major exceptions appear to be the SpeedTouch and
CDC-WDM drivers.
Signed-off-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Network interface is handled by upcoming gt_b3730 module.

Removed "GT-B3710" from comment, it is another modem with another USB ID.
Signed-off-by: NMarius B. Kotsbak <marius@kotsbak.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch
- ensures no IO takes place during resets
- reports resets to user space
Signed-off-by: NOliver Neukum <oneukum@suse.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch fixes a problem where data received from the gps is sometimes
transferred incompletely to the serial port. If used in native mode now
all data received via the bulk queue will be forwarded to the serial
port.
Signed-off-by: NHermann Kneissel <herkne@gmx.de>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Commit 1c6529e9 "USB: gadget: g_multi: fixed vendor and
product ID" replaced g_multi's vendor and product ID with
proper ID's from Linux Foundation.  This commit now updates
INF files in the Documentation/usb directory which were
omitted in the original commit.
Signed-off-by: NMichal Nazarewicz <mina86@mina86.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Adding support for the TavIR STK500 (id 0403:FA33)
Atmel AVR programmer device based on FTDI FT232RL.
Signed-off-by: NBenedek László <benedekl@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

Tested on my phone, the ttyUSB device is created and is fully
functional.
Signed-off-by: NElizabeth Jennifer Myers <elizabeth@sporksirc.net>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

This patch adds 4 device IDs for CP2102 based devices manufactured by
AC-Services. See http://www.ac-services.eu for further info.
Signed-off-by: NCraig Shelley <craig@microtron.org.uk>
Cc: stable <stable@kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>