If a spare device was marked faulty, it would not be reflected
in receiving nodes because it would mark it as activated and continue.
Continue the operation, so it may be set as faulty.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

The remove disk message does not need metadata_update_start(), but
can be an independent message.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NGuoqing Jiang <gqjiang@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

For cluster raid, if one disk couldn't be reach in one node, then
other nodes would receive the REMOVE message for the disk.

In receiving node, we can't call md_kick_rdev_from_array to remove
the disk from array synchronously since the disk might still be busy
in this node. So let's set a ClusterRemove flag on the disk, then
let the thread to do the removal job eventually.
Signed-off-by: NGuoqing Jiang <gqjiang@suse.com>
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

If a RESYNCING message with (0,0) has been sent before, do not send it
again. This avoids a resync ping pong between the nodes. We read
the bitmap lockresource's LVB to figure out the previous value
of the RESYNCING message.
Signed-off-by: NGoldwyn Rodrigues <rgoldwyn@suse.com>
Signed-off-by: NNeilBrown <neilb@suse.com>

The stripe_add_to_batch_list() function is called only if
stripe_can_batch() returned true, so there is no need for double check.
Signed-off-by: NRoman Gushchin <klamm@yandex-team.ru>
Cc: Neil Brown <neilb@suse.com>
Cc: linux-raid@vger.kernel.org
Signed-off-by: NNeilBrown <neilb@suse.com>

The total delay of HDMI hotplug detecting with 30ms is sometimes not
enoughtfor HDMI live status up with specific HDMI monitors in BSW platform.

After doing experiments for following monitors, it needs 80ms at least
for those worst cases.

Lenovo L246 1xwA (4 failed, necessary hot-plug delay: 58/40/60/40ms)
Philips HH2AP (9 failed, necessary hot-plug delay: 80/50/50/60/46/40/58/58/39ms)
BENQ ET-0035-N (6 failed, necessary hot-plug delay: 60/50/50/80/80/40ms)
DELL U2713HM (2 failed, necessary hot-plug delay: 58/59ms)
HP HP-LP2475w (5 failed, necessary hot-plug delay: 70/50/40/60/40ms)

It looks like 70-80 ms is BSW platform needs in some bad cases of the
monitors at this end (8 times delay at most). Keep less than 100ms for
HDCP pulse HPD low (with at least 100ms) to respond a plug out.
Reviewed-by: NCooper Chiou <cooper.chiou@intel.com>
Tested-by: NGary Wang <gary.c.wang@intel.com>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Cc: Shobhit Kumar <shobhit.kumar@intel.com>
Signed-off-by: NGary Wang <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450858295-12804-1-git-send-email-gary.c.wang@intel.comTested-by: NShobhit Kumar <shobhit.kumar@intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Fixes: 237ed86c ("drm/i915: Check live status before reading edid")
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit f8d03ea0)
[Jani: undo the file mode change of the original commit]
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Propagate the return value of platform_get_irq on failure.

A simplified version of the semantic match that finds the two cases where
no error code is returned at all is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret; expression e1,e2;
@@
(
if (\(ret < 0\|ret != 0\))
 { ... return ret; }
|
ret = 0
)
... when != ret = e1
    when != &ret
*if(...)
{
  ... when != ret = e2
      when forall
 return ret;
}
// </smpl>
Signed-off-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

dev->nr_luns reports the total number of luns available in a device
while dev->luns_per_chnl is the number of luns per channel.

When multiple channels are available, the offset is calculated from a
channel and lun id into a linear array. As it multiplies with
the total number of luns, we go out of bound when channel id > 0 and
causes the kernel to panic when we read a protected kernel memory area.
Signed-off-by: NMatias Bjørling <m@bjorling.me>
Signed-off-by: NJens Axboe <axboe@fb.com>

If null_blk is run in NULL_IRQ_TIMER mode and with queue_mode NULL_Q_RQ,
we need to restart the queue from the hrtimer interrupt. We can't
directly invoke the request_fn from that context, so punt the queue run
to async kblockd context.
Tested-by: NRabin Vincent <rabin@rab.in>
Signed-off-by: NJens Axboe <axboe@fb.com>

Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issueing "open" on be2net interface.

The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.

A. be2net is sending administrative open/close event to ocrdma holding
   device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
   So sequence of locks is rtnl_lock---> device_list lock

B.  When new ocrdma roce device gets registered, infiniband stack now
    takes rtnl_lock in ib_register_device() in GID initialization routines.
    So sequence of locks in this path is device_list lock ---> rtnl_lock.

This improper locking sequence causes deadlock.

In order to resolve the above deadlock condition, ocrdma intorduced a
patch to stop listening to administrative open/close events generated from
be2net driver. It now depends on link-state-change async-event generated from
CNA. This change leaves behind dead code which used to generate administrative
open/close events. This patch cleans-up all that dead code from be2net.
Reported-by: NDoug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: NSelvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: NDevesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issuing "open" on be2net interface.

The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.

A. be2net is sending administrative open/close event to ocrdma holding
   device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
   So sequence of locks is rtnl_lock---> device_list lock

B.  When new ocrdma roce device gets registered, infiniband stack now
    takes rtnl_lock in ib_register_device() in GID initialization routines.
    So sequence of locks in this path is device_list lock ---> rtnl_lock.

This improper locking sequence causes deadlock.

With this patch we stop using administrative open and close events
injected by be2net driver. These events were used to dispatch PORT_ACTIVE
and PORT_ERROR events to the IB-stack. This patch implements a logic
to receive async-link-events generated from CNA whenever link-state-change
is detected. Now on, these async-events will be used to dispatch
PORT_ACTIVE and PORT_ERROR events to IB-stack.

Depending on async-events from CNA removes the need to hold device-list-mutex
and thus breaks the busy-wait scenario.
Reported-by: NDoug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: NSelvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: NDevesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Dispatch only port event to IB stack when port state changes.
Don't explicitly modify qps to error. Let application listen to
port events on async event queue or let QP fail with retry-exceeded
completion error.
Signed-off-by: NPadmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: NDevesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

vlan-id is wrongly getting as 0 when PFC is enabled.
Set vlan-id configured by user in QP parameters.
In case vlan interface is not used, flash a warning to
user to configure vlan and assign vlan-id as 0 in qp params.

Fixes: dbf727de ('IB/core: Use GID table in AH creation and dmac resolution')
Cc: Matan Barak <matanb@mellanox.com>
Signed-off-by: NDevesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

When sysrq is triggered from console, serial driver for SUN hypervisor
console receives a console break and enables the sysrq. It expects a valid
sysrq char following with break. Meanwhile if driver receives 'NULL'
ASCII char then it disables sysrq and sysrq handler will never be invoked.

This fix skips calling uart sysrq handler when 'NULL' is received while
sysrq is enabled.
Signed-off-by: NVijay Kumar <vijay.ac.kumar@oracle.com>
Acked-by: NKarl Volz <karl.volz@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Constifies sunhv_ops structures in tty's serial
driver since they are not modified after their
initialization.

Detected and found using Coccinelle.
Suggested-by: NJulia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: NAya Mahfouz <mahfouz.saif.elyazal@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In the original code, if we succeeded on the last iteration through the
loop then we still returned failure.

Fixes: 389e4e04 ('qlcnic: fix a timeout loop')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NCM buffer sizes are negotiated with the device independently of
the network device MTU.  The RX buffers are allocated by the
usbnet framework based on the rx_urb_size value set by cdc_ncm. A
single RX buffer can hold a number of MTU sized packets.

The default usbnet change_mtu ndo only modifies rx_urb_size if it
is equal to hard_mtu.  And the cdc_ncm driver will set rx_urb_size
and hard_mtu independently of each other, based on dwNtbInMaxSize
and dwNtbOutMaxSize respectively. It was therefore assumed that
usbnet_change_mtu() would never touch rx_urb_size.  This failed to
consider the case where dwNtbInMaxSize and dwNtbOutMaxSize happens
to be equal.

Fix by implementing an NCM specific change_mtu ndo, modifying the
netdev MTU without touching the buffer size settings.
Signed-off-by: NBjørn Mork <bjorn@mork.no>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently the needed_headroom field for the geneve device is left
to the default value.

This patch set it to space required for basic geneve encapsulation,
so that we can avoid the skb head re-allocation on xmit.

This give a 6% speedup for unsegment traffic on geneve tunnel.

v1 -> v2:
  - add ETH_HLEN for the lower device to the needed headroom
Signed-off-by: NPaolo Abeni <pabeni@redhat.com>
Acked-by: NHannes Frederic Sowa <hannes@stressinduktion.org>
Acked-by: NJohn W. Linville <linville@tuxdriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The "domain" variable needs to be signed for the error handling to work.

Fixes: 8def3103 (cpufreq: arm_big_little: add SCPI interface driver)
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Acked-by: NViresh Kumar <viresh.kumar@linaro.org>
Acked-by: NSudeep Holla <sudeep.holla@arm.com>
Signed-off-by: NRafael J. Wysocki <rafael.j.wysocki@intel.com>

Atomic changes broke check_digital_port_conflicts(). It needs to look
at the global situation instead of just trying to find a conflict
within the current atomic state.

This bug made my HSW explode spectacularly after I had split the DDI
encoders into separate DP and HDMI encoders. With the fix, things
seem much more solid.

I hope holding the connection_mutex is enough protection that we can
actually walk the connectors even if they're not part of the current
atomic state...

v2: Regenerate the patch so that it actually applies (Jani)

Cc: stable@vger.kernel.org
Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Fixes: 5448a00d ("drm/i915: Don't use staged config in check_digital_port_conflicts()")
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449764551-12466-1-git-send-email-ville.syrjala@linux.intel.com
(cherry picked from commit 0bff4858)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Commit 0ef2f05c uses vmalloc for WR buffers
when needed and uses kvfree to free the buffers. It missed changing kfree
to kvfree in mlx4_ib_destroy_srq().
Reported-by: NMatthew Finaly <matt@Mellanox.com>
Signed-off-by: NWengang Wang <wen.gang.wang@oracle.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Previously, cma_match_net_dev called cma_protocol_roce which
tried to verify that the IB device uses RoCE protocol. However,
if rdma_id wasn't bound to a port, then the check would occur
against the first port of the device without regard to whether
that port was even of the same type as the type of port the
incoming packet was received on.

Fix this by passing the port of the request and only checking
against the same port of the device.
Reported-by: NOr Gerlitz <gerlitz.or@gmail.com>
Fixes: b8cab5da ('IB/cma: Accept connection without a valid netdev on RoCE')
Signed-off-by: NMatan Barak <matanb@mellanox.com>
Signed-off-by: NDoug Ledford <dledford@redhat.com>

Commit 1299653a ("sh_eth: fix descriptor access endianness") only
addressed the 32-bit buffer address field byte-swapping  but the driver
still accesses 16-bit frame/buffer length descriptor fields without the
necessary byte-swapping -- which should affect the big-endian kernels.
In order to be able to use {cpu|edmac}_to_{edmac|cpu}(), we need to declare
the RX/TX descriptor word 1 as a 32-bit field and use shifts/masking to
access the 16-bit subfields (which gets rid of the ugly #ifdef'ery too)...
Signed-off-by: NSergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Packets that arrive from real hardware devices have ip_summed ==
CHECKSUM_UNNECESSARY if the hardware verified the checksums, or
CHECKSUM_NONE if the packet is bad or it was unable to verify it. The
current version of veth will replace CHECKSUM_NONE with
CHECKSUM_UNNECESSARY, which causes corrupt packets routed from hardware to
a veth device to be delivered to the application. This caused applications
at Twitter to receive corrupt data when network hardware was corrupting
packets.

We believe this was added as an optimization to skip computing and
verifying checksums for communication between containers. However, locally
generated packets have ip_summed == CHECKSUM_PARTIAL, so the code as
written does nothing for them. As far as we can tell, after removing this
code, these packets are transmitted from one stack to another unmodified
(tcpdump shows invalid checksums on both sides, as expected), and they are
delivered correctly to applications. We didn’t test every possible network
configuration, but we tried a few common ones such as bridging containers,
using NAT between the host and a container, and routing from hardware
devices to containers. We have effectively deployed this in production at
Twitter (by disabling RX checksum offloading on veth devices).

This code dates back to the first version of the driver, commit
<e314dbdc> ("[NET]: Virtual ethernet device driver"), so I
suspect this bug occurred mostly because the driver API has evolved
significantly since then. Commit <0b796750> ("net/veth: Fix
packet checksumming") (in December 2010) fixed this for packets that get
created locally and sent to hardware devices, by not changing
CHECKSUM_PARTIAL. However, the same issue still occurs for packets coming
in from hardware devices.
Co-authored-by: NEvan Jones <ej@evanjones.ca>
Signed-off-by: NEvan Jones <ej@evanjones.ca>
Cc: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Cc: Phil Sutter <phil@nwl.cc>
Cc: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: NVijay Pandurangan <vijayp@vijayp.ca>
Acked-by: NCong Wang <cwang@twopensource.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

0x4e is the runtime address normally associated with perihperal ICs.
0x45 is not a valid runtime address.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

The primary PMICs use 0x3a3 as their hardware address, not 0x3e3.
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Signed-off-by: NOlof Johansson <olof@lixom.net>

blk_end_request_all may free request, so we need to save
request_queue pointer before blk_end_request_all call.

The problem was introduced in commit cf8ecc5a
("null_blk: guarantee device restart in all irq modes")
and causes general protection fault with slab poisoning
enabled.

Fixes: cf8ecc5a ("null_blk: guarantee device
       restart in all irq modes")
Signed-off-by: NMike Krinkin <krinkin.m.u@gmail.com>
Reviewed-by: NMing Lei <tom.leiming@gmail.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

This patch fixes a lost request discovered during IO + hot removal.

The driver's pci removal deletes gendisks prior to shutting down the
controller to allow dirty data to sync. Dirty data can not be synced on
a surprise removal, though, and would potentially block indefinitely.

The driver previously had marked the queue as dying in this scenario
to prevent new requests from attempting, however it will still block
for requests that already entered the queue. This patch fixes this by
quiescing IO first, then aborting the requeued requests before deleting
disks.
Reported-by: NSujith Pandel <sujith_pandel@dell.com>
Signed-off-by: NKeith Busch <keith.busch@intel.com>
Tested-by: NSujith Pandel <sujith_pandel@dell.com>
Signed-off-by: NJens Axboe <axboe@fb.com>

The total delay of HDMI hotplug detecting with 30ms have already
been split into a resolution of 3 retries of 10ms each, for the worst
cases. But it still suffered from only waiting 10ms at most in
intel_hdmi_detect(). This patch corrects it by reading hotplug status
with 4 times at most for 30ms delay.

v2:
- straight up to loop execution for more clear in code readability
- mdelay will replace with msleep by Daniel's new patch

	drm/i915: mdelay(10) considered harmful

- suggest to re-evaluate try times for being compatible to old HDMI monitor
Reviewed-by: NCooper Chiou <cooper.chiou@intel.com>
Tested-by: NGary Wang <gary.c.wang@intel.com>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Gavin Hindman <gavin.hindman@intel.com>
Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: Shashank Sharma <shashank.sharma@intel.com>
Signed-off-by: NGary Wang <gary.c.wang@intel.com>
[danvet: fixup conflict with s/mdelay/msleep/ patch.]
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 61fb3980)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

I missed this myself when reviewing

commit 237ed86c
Author: Sonika Jindal <sonika.jindal@intel.com>
Date:   Tue Sep 15 09:44:20 2015 +0530

    drm/i915: Check live status before reading edid

Long sleeps like this really shouldn't waste cpu cycles spinning.

Cc: Sonika Jindal <sonika.jindal@intel.com>
Cc: "Wang, Gary C" <gary.c.wang@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449859455-32609-1-git-send-email-daniel.vetter@ffwll.chReviewed-by: NSonika Jindal <sonika.jindal@intel.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 71a199ba)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The vma may have been rebound between the last time the cursor was
enabled and now, so skipping the cursor gtt offset deduction is not
safe unless we would also reset cursor_bo to NULL when disabling the
cursor. Just thow cursor_bo to the bin instead since it's lost all
other uses thanks to universal plane support.

Chris pointed out that cursor updates are currently too slow
via universal planes that micro optimizations like these wouldn't
even help.

v2: Add a note about futility of micro optimizations (Chris)

Cc: drm-intel-fixes@lists.freedesktop.org
References: http://lists.freedesktop.org/archives/intel-gfx/2015-December/082976.html
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450107302-17171-1-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 1264859d)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Turns out CHV pipe C was glued on somewhat poorly, and there's something
wrong with the cursor. If the cursor straddles the left screen edge,
and is then moved away from the edge or disabled, the pipe will often
underrun. If enough underruns are triggered quickly enough the pipe
will fall over and die (it just scans out a solid color and reports
a constant underrun). We need to turn the disp2d power well off and
on again to recover the pipe.

None of that is very nice for the user, so let's just refuse to place
the cursor in the compromised position. The ddx appears to fall back
to swcursor when the ioctl returns an error, so theoretically there's
no loss of functionality for the user (discounting swcursor bugs).
I suppose most cursors images actually have the hotspot not exactly
at 0,0 so under typical conditions the fallback will in fact kick in
as soon as the cursor touches the left edge of the screen.

Any atomic compositor should anyway be prepared to fall back to
GPU composition when things don't work out, so there should be no
problem with those.

Other things that I tried to solve this include flipping all
display related clock gating knobs I could find, increasing the
minimum gtt alignment all the way up to 512k. I also tried to see
if there are more specific screen coordinates that hit the bug, but
the findings were somewhat inconclusive. Sometimes the failures
happen almost across the whole left edge, sometimes more at the very
top and around the bottom half. I wasn't able to find any real pattern
to these variations, so it seems our only choice is to just refuse
to straddle the left screen edge at all.

Cc: stable@vger.kernel.org
Cc: Jason Plum <max@warheads.net>
Testcase: igt/kms_chv_cursor_fail
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92826Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450459479-16286-1-git-send-email-ville.syrjala@linux.intel.comSigned-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit b29ec92c)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Limit busywaiting only to the request currently being processed by the
GPU. If the request is not currently being processed by the GPU, there
is a very low likelihood of it being completed within the 2 microsecond
spin timeout and so we will just be wasting CPU cycles.

v2: Check for logical inversion when rebasing - we were incorrectly
checking for this request being active, and instead busywaiting for
when the GPU was not yet processing the request of interest.

v3: Try another colour for the seqno names.
v4: Another colour for the function names.

v5: Remove the forced coherency when checking for the active request. On
reflection and plenty of recent experimentation, the issue is not a
cache coherency problem - but an irq/seqno ordering problem (timing issue).
Here, we do not need the w/a to force ordering of the read with an
interrupt.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-4-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 821485dc)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

When waiting for high frequency requests, the finite amount of time
required to set up the irq and wait upon it limits the response rate. By
busywaiting on the request completion for a short while we can service
the high frequency waits as quick as possible. However, if it is a slow
request, we want to sleep as quickly as possible. The tradeoff between
waiting and sleeping is roughly the time it takes to sleep on a request,
on the order of a microsecond. Based on measurements of synchronous
workloads from across big core and little atom, I have set the limit for
busywaiting as 10 microseconds. In most of the synchronous cases, we can
reduce the limit down to as little as 2 miscroseconds, but that leaves
quite a few test cases regressing by factors of 3 and more.

The code currently uses the jiffie clock, but that is far too coarse (on
the order of 10 milliseconds) and results in poor interactivity as the
CPU ends up being hogged by slow requests. To get microsecond resolution
we need to use a high resolution timer. The cheapest of which is polling
local_clock(), but that is only valid on the same CPU. If we switch CPUs
because the task was preempted, we can also use that as an indicator that
 the system is too busy to waste cycles on spinning and we should sleep
instead.

__i915_spin_request was introduced in
commit 2def4ad9 [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Apr 7 16:20:41 2015 +0100

     drm/i915: Optimistically spin for the request completion

v2: Drop full u64 for unsigned long - the timer is 32bit wraparound safe,
so we can use native register sizes on smaller architectures. Mention
the approximate microseconds units for elapsed time and add some extra
comments describing the reason for busywaiting.

v3: Raise the limit to 10us
v4: Now 5us.
Reported-by: NJens Axboe <axboe@kernel.dk>
Link: https://lkml.org/lkml/2015/11/12/621Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-3-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit ca5b721e)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The busywait in __i915_spin_request() does not respect pending signals
and so may consume the entire timeslice for the task instead of
returning to userspace to handle the signal.

In the worst case this could cause a delay in signal processing of 20ms,
which would be a noticeable jitter in cursor tracking. If a higher
resolution signal was being used, for example to provide fairness of a
server timeslices between clients, we could expect to detect some
unfairness between clients (i.e. some windows not updating as fast as
others). This issue was noticed when inspecting a report of poor
interactivity resulting from excessively high __i915_spin_request usage.

Fixes regression from
commit 2def4ad9 [v4.2]
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date:   Tue Apr 7 16:20:41 2015 +0100

     drm/i915: Optimistically spin for the request completion

v2: Try to assess the impact of the bug
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NTvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc; "Rogozhkin, Dmitry V" <dmitry.v.rogozhkin@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com>
Cc: Eero Tamminen <eero.t.tamminen@intel.com>
Cc: "Rantala, Valtteri" <valtteri.rantala@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1449833608-22125-2-git-send-email-chris@chris-wilson.co.uk
(cherry picked from commit 91b0c352)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

If we fail to reconstruct the BIOS fb (e.g., because the FB is too
large), we'll be left with plane state that indicates the primary plane
is visible yet has a NULL fb.  This mismatch causes problems later on
(e.g., for the watermark code).  Since we've failed to reconstruct the
BIOS FB, the best solution is to just disable the primary plane and
pretend the BIOS never had it enabled.

v2: Add intel_pre_disable_primary() call (Maarten)

Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: drm-intel-fixes@lists.freedesktop.org
Signed-off-by: NMatt Roper <matthew.d.roper@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1449171462-30763-2-git-send-email-matthew.d.roper@intel.com
(cherry picked from commit 200757f5)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

As we mark the preallocated objects as bound, we should also flag them
correctly as being map-and-fenceable (if appropriate!) so that later
users do not get confused and try and rebind the pinned vma in order to
get a map-and-fenceable binding.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: "Goel, Akash" <akash.goel@intel.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: drm-intel-fixes@lists.freedesktop.org
Link: http://patchwork.freedesktop.org/patch/msgid/1448029000-10616-1-git-send-email-chris@chris-wilson.co.ukReviewed-by: NJesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit d0710abb)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

The cursor code tries to treat base==0 to mean disabled. That fails
when the cursor bo gets bound at ggtt offset 0, and the user is left
looking at an invisible cursor.

We lose the disabled->disabled optimization, but that seems like
something better handled at a slightly higher level.

Cc: drm-intel-fixes@lists.freedesktop.org
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1450091808-32607-3-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
(cherry picked from commit 663f3122)
Signed-off-by: NJani Nikula <jani.nikula@intel.com>

Unlike DW5550, Dell DW5813 is a mobile broadband card with no ARP
capabilities: the patch makes this device to use wwan_noarp_info struct
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Unlike DW5550, Dell DW5812 is a mobile broadband card with no ARP
capabilities: the patch makes this device to use wwan_noarp_info struct
Signed-off-by: NDaniele Palmas <dnlplm@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>