- 13 3月, 2012 2 次提交
-
-
由 Or Gerlitz 提交于
Set the MTU for IB ports in the driver instead of using the firmware default of 2KB (the driver defaults to 4KB). Allow for dynamic mtu configuration through a new, per-port sysfs entry. Since there's a dependency between the port MTU and the max number of HW VLs the port can support, apply a mim/max approach, using a loop that goes down from the highest possible number of VLs to the lowest, using the firmware return status to know whether the requested number of VLs is possible with a given MTU. For now, as with the dynamic link type change / VPI support, the sysfs entry to change the mtu is exposed only when NOT running in SR-IOV mode. To allow changing the MTU for the master in SR-IOV mode, primary-function-initiated FLR (Function Level Reset) needs to be implemented. Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Roland Dreier 提交于
Commit 22c8bff6 ("mlx4_core: Exported functions can't be static") fixed most of this up, but forgot about mlx4_is_slave_active(). Fix this one too. Cc: <stable@vger.kernel.org> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 26 2月, 2012 1 次提交
-
-
由 Eli Cohen 提交于
ConnectX devices have a limit on the number of mappings that can be done on an FMR before having to call sync_tpt. The current mlx4_ib driver reports the limit correctly in max_map_per_fmr in .query_device(), but mlx4_core doesn't check it when actually allocating FMRs. Add a max_fmr_maps field to struct mlx4_caps and enforce this maximum value on FMR allocations. Signed-off-by: NEli Cohen <eli@mellanox.com> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 23 1月, 2012 2 次提交
-
-
由 Marcel Apfelbaum 提交于
Num mtts from profile is really the number of mtt segments. Thus, in make profile, to get the proper number of MTT entries, must multiply num_mtts by mtts per segment. Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marcel Apfelbaum 提交于
The Virtual Functions should not be aware their function number. Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 12月, 2011 1 次提交
-
-
由 Yevgeny Petrilin 提交于
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 20 12月, 2011 3 次提交
-
-
由 Rusty Russell 提交于
module_param(bool) used to counter-intuitively take an int. In fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy trick. It's time to remove the int/unsigned int option. For this version it'll simply give a warning, but it'll break next kernel version. (Thanks to Joe Perches for suggesting coccinelle for 0/1 -> true/false). Cc: "David S. Miller" <davem@davemloft.net> Cc: netdev@vger.kernel.org Signed-off-by: NRusty Russell <rusty@rustcorp.com.au> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
New FW can give clues to driver regarding default port type and whether or not we should default to link sensing on the port. 2 bits are added to QUERY_PORT command: 1. suggested_type: This bit gives a hint whether the default port type should be IB or Ethernet. The driver will use this hint in case the user didn't specify explicitly the link layer type he wants to set. 2. default_sense: If this bit is set, we would sense the port type on start-up and default the port to link sensing Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
For ConnectX3 devices, we allow link sensing only if FW explicitly reported it supports the feature. For older versions (ConnectX1 and 2), if the card supports both link layer types (Ethenet and Infiniband), link sensing is supported. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 14 12月, 2011 4 次提交
-
-
由 Jack Morgenstein 提交于
1. Added module parameters sr_iov and probe_vf for controlling enablement of SRIOV mode. 2. Increased default max num-qps, num-mpts and log_num_macs to accomodate SRIOV mode 3. Added port_type_array as a module parameter to allow driver startup with ports configured as desired. In SRIOV mode, only ETH is supported, and this array is ignored; otherwise, for the case where the FW supports both port types (ETH and IB), the port_type_array parameter is used. By default, the port_type_array is set to configure both ports as IB. 4. When running in sriov mode, the master needs to initialize the ICM eq table to hold the eq's for itself and also for all the slaves. 5. mlx4_set_port_mask() now invoked from mlx4_init_hca, instead of in mlx4_dev_cap. 6. Introduced sriov VF (slave) device startup/teardown logic (mainly procedures mlx4_init_slave, mlx4_slave_exit, mlx4_slave_cap, mlx4_slave_exit and flow modifications in __mlx4_init_one, mlx4_init_hca, and mlx4_setup_hca). VFs obtain their startup information from the PF (master) device via the comm channel. 7. In SRIOV mode (both PF and VF), MSI_X must be enabled, or the driver aborts loading the device. 8. Do not allow setting port type via sysfs when running in SRIOV mode. 9. mlx4_get_ownership: Currently, only one PF is supported by the driver. If the HCA is burned with FW which enables more than one PF, only one of the PFs is allowed to run. The first one up grabs a FW ownership semaphone -- all other PFs will find that semaphore taken, and the driver will not allow them to run. Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NLiran Liss <liranl@mellanox.co.il> Signed-off-by: NMarcel Apfelbaum <marcela@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Marcel Apfelbaum 提交于
In the previous implementation mtts are managed by: 1. order - log(mtt segments), 'mtt segment' groups several mtts together. 2. first_seg - segment location relative to mtt table. In the current implementation: 1. order - log(mtts) rather than segments 2. offset - mtt index in mtt table Note: The actual mtt allocation is made in segments but it is transparent to callers. Rational: The mtt resource holders are not interested on how the allocation of mtt is done, but rather on how they will use it. Signed-off-by: NMarcel Apfelbaum <marcela@dev.mellanox.co.il> Reviewed-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Eugenia Emantayev 提交于
Let multicast/unicast attaching flow go through resource tracker. The PF is the one responsible for managing all the steering entries. Define and use module parameter that determines the number of qps per multicast group. Minor changes in function calls according to changed prototype. Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Jack Morgenstein 提交于
Port mask now has additional state. Port can be set as "none". In this case neither the mlx4_en or mlx4_ib drivers take ownership of the port. In multifunction mode there is an option to set the vfs as single ported devices. (in single function mode, both physical ports belong to same function) Signed-off-by: NJack Morgenstein <jackm@dev.mellanox.co.il> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 11 8月, 2011 1 次提交
-
-
由 Jeff Kirsher 提交于
Moves the Mellanox driver into drivers/net/ethernet/mellanox/ and make the necessary Kconfig and Makefile changes. CC: Roland Dreier <roland@kernel.org> Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>
-
- 04 8月, 2011 1 次提交
-
-
由 Yevgeny Petrilin 提交于
For older FW versions, fixing the usage of per port Mac table. For each port we must define the base QP number, which is passed to the HW. Setting the correct value in SET_PORT FW command to enable the steering. Reported-by: NRoland Dreier <roland@purestorage.com> Tested-by: NRoland Dreier <roland@purestorage.com> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 19 7月, 2011 2 次提交
-
-
由 Or Gerlitz 提交于
ConnectX devices support a set of flow counters that can be attached to a set containing one or more QPs. Each such counter tracks receive and transmit packets and bytes of these QPs. This patch queries the device to check support for counters, handles initialization of the HCA to enable counters, and initializes a bitmap allocator to control counter allocations. Derived from patch by Eli Cohen <eli@mellanox.co.il>. Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
由 Or Gerlitz 提交于
Query another dword containing up to 32 extended device capabilities and merge it into struct mlx4_caps.flags. Update the code that handles the current extended device capabilities (e.g UDP RSS, WoL, vep steering, etc) to use the extended device cap flags field instead of a field per extended capability. Initial patch done by Eli Cohen <eli@mellanox.co.il>. Signed-off-by: NOr Gerlitz <ogerlitz@mellanox.co.il> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 28 6月, 2011 1 次提交
-
-
由 Sergei Shtylyov 提交于
Commit 725c8999 (mlx4_en: Reporting HW revision in ethtool -i) added code to read the revision ID from the PCI configuration register while it's already stored by PCI subsystem in the 'revision' field of 'struct pci_dev'... While at it, move the code being changed a bit in order to not break the initialization sequence. Signed-off-by: NSergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 08 4月, 2011 1 次提交
-
-
由 Yevgeny Petrilin 提交于
When bringing the port up, performing a SENSE_PORT command To try and check to which physical link type (IB or Ethernet) the physical port is connected. In case there is no valid link partner, the port will come up as its supported default. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 24 3月, 2011 6 次提交
-
-
由 Eli Cohen 提交于
Using blue flame can improve latency by allowing the HW to more efficiently access the WQE. This patch presents two functions that are used to allocate or release HW resources for using blue flame; the caller need to supply a struct mlx4_bf object when allocating resources. Consumers that make use of this API should post doorbells to the UAR object pointed by the initialized struct mlx4_bf; Signed-off-by: NEli Cohen <eli@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
For Ethernet mode only, When we want to register QP as promiscuous, it must be added to all the existing steering entries and also to the default one. The promiscuous QP might also be on of "real" QPs, which means we need to monitor every entry to avoid duplicates and ensure we close an entry when all it has is promiscuous QPs. Same mechanism both for unicast and multicast. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
The same packet steering mechanism would be used both for IB and Ethernet, Both multicasts and unicasts. This commit prepares the general infrastructure for this. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
HW revision is derived from device ID and rev id. Signed-off-by: NEugenia Emantayev <eugenia@mellanox.co.il> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
The driver queries the FW for WOL support. Ethtool get/set_wol is implemented accordingly. Only magic packets are supported at the time. Signed-off-by: NIgor Yarovinsky <igory@mellanox.co.il> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
Adding a pool of MSI-X vectors and EQs that can be used explicitly by mlx4_core customers (mlx4_ib, mlx4_en). The consumers will assign their own names to the interrupt vectors. Those vectors are not opened at mlx4 device initialization, opened by demand. Changed the max number of possible EQs according to the new scheme, no longer relies on on number of cores. The new functionality is exposed through mlx4_assign_eq() and mlx4_release_eq(). Customers that do not use the new API will get completion vectors as before. Signed-off-by: NMarkuze Alex <markuze@mellanox.co.il> Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 23 3月, 2011 1 次提交
-
-
由 David Dillow 提交于
By default, each device is assumed to be able only handle 64 KB chunks during DMA. By giving the segment size a larger value, the block layer will coalesce more S/G entries together for SRP, allowing larger requests with the same sg_tablesize setting. The block layer is the only direct user of it, though a few IOMMU drivers reference it as well for their *_map_sg coalescing code. pci-gart_64 on x86, and a smattering on on sparc, powerpc, and ia64. Since other IB protocols could potentially see larger segments with this, let's check those: - iSER is fine, because you limit your maximum request size to 512 KB, so we'll never overrun the page vector in struct iser_page_vec (128 entries currently). It is independent of the DMA segment size, and handles multi-page segments already. - IPoIB is fine, as it maps each page individually, and doesn't use ib_dma_map_sg(). - RDS appears to do the right thing and has no dependencies on DMA segment size, but I don't claim to have done a complete audit. - NFSoRDMA and 9p are OK -- they do not use ib_dma_map_sg(), so they doesn't care about the coalescing. - Lustre's ko2iblnd does not care about coalescing -- it properly walks the returned sg list. This patch ups the value on Mellanox hardware to 1 GB, which matches reported firmware limits on mlx4. Signed-off-by: NDavid Dillow <dillowda@ornl.gov> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 29 1月, 2011 1 次提交
-
-
由 Yevgeny Petrilin 提交于
...as already added to pci.ids. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NRoland Dreier <roland@purestorage.com>
-
- 13 1月, 2011 1 次提交
-
-
由 Roland Dreier 提交于
Some systems have PCI addresses that don't fit in unsigned long (eg some 32-bit PowerPC 440 systems have 36-bit bus addresses). Fix up mlx4 drivers by using phys_addr_t where appropriate, so we don't truncate any PCI resource addresses before ioremapping them. Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
- 29 9月, 2010 1 次提交
-
-
由 Eli Cohen 提交于
As there are now machines with a lot more physical memory, we need to be able to register more memory. This patch lifts the upper limit of log_mtts_per_seg from 5 to 7, increasing the amount of memory that can be registered. Signed-off-by: NEli Cohen <eli@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
- 25 8月, 2010 3 次提交
-
-
由 Yevgeny Petrilin 提交于
Adding capability for RSS for UDP traffic, hashing is done based on IP addresses and UDP port number. The support depends on HW/FW capabilities. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
The report now based on query from FW, giving the correct tranciever type and link speed. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
由 Yevgeny Petrilin 提交于
The selftest includes 5 features: 1. Interrupt test: Executing commands and receiving command completion on all our interrupt vectors. 2. Link test: Verifying we are connected to valid link partner. 3. Speed test: Check that we negotiated link speed correctly. 4. Registers test: Activate HW health check command. 5. Loopback test: Send a packet on loopback interface and catch it on RX side. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 16 7月, 2010 1 次提交
-
-
由 Joe Perches 提交于
Remove near duplication of format string constants by using the newly introduced vsprintf extention %pV to reduce text by 20k or so. $ size drivers/net/mlx4/built-in.o* text data bss dec hex filename 161367 1866 48784 212017 33c31 drivers/net/mlx4/built-in.o 142621 1866 46248 190735 2e90f drivers/net/mlx4/built-in.o.new Use printk_once as appropriate. Convert printks to pr_<level>, some bare printks now use pr_cont. Remove now unused #define PFX. Signed-off-by: NJoe Perches <joe@perches.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 30 3月, 2010 1 次提交
-
-
由 Tejun Heo 提交于
include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: NTejun Heo <tj@kernel.org> Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
-
- 19 3月, 2010 1 次提交
-
-
由 Greg Kroah-Hartman 提交于
This fixes a sysfs lockdep warning in the mlx4 code. Cc: Yinghai Lu <yinghai@kernel.org> Cc: Eric Biederman <ebiederm@xmission.com> Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>
-
- 08 1月, 2010 1 次提交
-
-
由 Alexey Dobriyan 提交于
Use DEFINE_PCI_DEVICE_TABLE() so we get place PCI ids table into correct section in every case. Signed-off-by: NAlexey Dobriyan <adobriyan@gmail.com> Signed-off-by: NDavid S. Miller <davem@davemloft.net>
-
- 07 1月, 2010 1 次提交
-
-
由 Eli Cohen 提交于
If mlx4_init_port_info() fails, cleanup the initialized ports only. Signed-off-by: NEli Cohen <eli@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
- 15 10月, 2009 1 次提交
-
-
由 Eli Cohen 提交于
Add MT26438 (ConnectX EN 40GigE PCIe 2.0 5GT/s) to the list of supported devices. Signed-off-by: NEli Cohen <eli@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
- 08 10月, 2009 1 次提交
-
-
由 Yevgeny Petrilin 提交于
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-
- 06 9月, 2009 1 次提交
-
-
由 Yevgeny Petrilin 提交于
On the error path of mlx4_init_hca(), mlx4_close_hca() is called, followed by mlx4_free_icms() and mlx4_UNMAP_FA(). But both those functions are also called from mlx4_close_hca(), which leads to a double free. Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il> Signed-off-by: NRoland Dreier <rolandd@cisco.com>
-