This is the only place where this function is used.  Make it static.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The ID_VACANT definition has become entirely irrelevant by now.

The is_syncer_block_id() macro does not improve the code, so eliminated
it.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In file included from drivers/block/drbd/drbd_main.c:54:                        drivers/block/drbd/drbd_int.h:1190: warning: parameter has incomplete type

Forward declarations of enums do not work.

Fix it unpleasantly by moving the prototype.

Cc: Jens Axboe <axboe@kernel.dk>
Signed-off-by: NLars Ellenberg <drbd-dev@lists.linbit.com>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>

Found these with the help of ispell -l.
Signed-off-by: NBart Van Assche <bvanassche@acm.org>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>

An administrative detach used to request a state change directly to D_DISKLESS,
first suspending IO to avoid the last put_ldev() occuring from an endio handler,
potentially in irq context.

This is not enough on the receiving side (typically secondary), we may miss
some peer_req on the way to local disk, which then may do the last put_ldev()
from their drbd_peer_request_endio().

This patch makes the detach always go through the intermediate D_FAILED state.
We may consider to rename it D_DETACHING.

Alternative approach would be to create yet an other work item to be scheduled
on the worker, do the destructor work from there, and get the timing right.

manually picked commit 564040f from the drbd 8.4 branch.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The old (optimistic) implementation could shrink the bio size
on an primary device.

Shrinking the bio size on a primary device is bad. Since there
we might get BIOs with the old (bigger) size shortly after
we published the new size.

The new implementation is more conservative, and eventually
increases the max_bio_size on a primary device (which is valid).
It does so, when it knows the local limit AND the remote limit.

 We cache the last seen max_bio_size of the peer in the meta
 data, and rely on that, to make the operation of single
 nodes more efficient.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In case a write failes on the local disk, go into D_INCONSISTENT
disk state. That causes future reads of that block to be shipped
to the peer.

Read retry remote was already in place.

Actually the documentation needs to get fixed now. Since the
application is still shielded from the error. (as long as we have
only a single disk failing) The difference to detach is that
we keep the disk. And therefore might keep all the other, still
working sectors up to date.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout.  Give
them an explicit include via the following $0.02 script.

 =========================================
 #!/bin/bash
 MANUAL=""
 for i in `git grep -l 'prefetch(.*)' .` ; do
 	grep -q '<linux/prefetch.h>' $i
 	if [ $? = 0 ] ; then
 		continue
 	fi

 	(	echo '?^#include <linux/?a'
 		echo '#include <linux/prefetch.h>'
 		echo .
 		echo w
 		echo q
 	) | ed -s $i > /dev/null 2>&1
 	if [ $? != 0 ]; then
 		echo $i needs manual fixup
 		MANUAL="$i $MANUAL"
 	fi
 done
 echo ------------------- 8\<----------------------
 echo vi $MANUAL
 =========================================
Signed-off-by: NPaul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
  non-network drivers and the fib_trie.c case    - Linus ]
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Fixes generated by 'codespell' and manually reviewed.
Signed-off-by: NLucas De Marchi <lucas.demarchi@profusion.mobi>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Now that we do no longer in-place endian-swap the bitmap, we allow
selected bitmap operations (testing bits, sometimes even settting bits)
during some bulk operations.

This caused us to hit a lot of FIXME asserts similar to
	FIXME asender in drbd_bm_count_bits,
	bitmap locked for 'write from resync_finished' by worker
Which now is nonsense: looking at the bitmap is perfectly legal
as long as it is not being resized.

This cosmetic patch defines some flags to describe expectations in finer
detail, so the asserts in e.g. bm_change_bits_to() can be skipped if
appropriate.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

All decisions about sync, sync direction, and wether or not to
allow a connect or attach are based on our set of UUIDs to tag a
data generation.

Log changes to the UUIDs whenever they occur,
logging "new current UUID P:Q:R:S" is more useful
than "Creating new current UUID".
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The test if rs_pending_cnt == 0 was too weak. Using Test for
unacked_cnt == 0 instead. Moved that into the worker.

Since unacked_cnt gets already increased when an P_RS_DATA_REQ
comes in.

Also using a timer to make Ahead -> SyncSource -> Ahead cycles
slower...
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

See also commit from 2009-08-15
"drbd_uuid_compare(): Do not full sync in case a P_SYNC_UUID packet gets lost."

We saw cases where the History UUIDs where not as expected. So the
detection of the special case did not trigger. With the sync UUID
no longer being a random number, but deducible from the previous
bitmap UUID, the detection of this special case becomes more
reliable.

The SyncUUID now is the previous bitmap UUID + 0x1000000000000.

Rule 5a:
Cs = H1p & H1p + Offset = Bp
  Connection was lost before SyncUUID Packet came through.
  Corrent (peer) UUIDs:
   Bp = H1p
   H1p = H2p
   H2p = 0
  Become Sync target.

Rule 7a:
Cp = H1s & H1s + Offset = Bs
  Connection was lost before SyncUUID Packet came through.
  Correct (own) UUIDs:
   Bs = H1s
   H1s = H2s
   H2s = 0
  Become Sync source.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Besides removed a few lines of code, this moves the inspection
of the state from before the queuing process to after the queuing.
I.e. more closely to the actual invocation of the work.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

When the sync source node replies to a P_RS_DATA_REQUEST packet
when it is already in ahead mode. I.e. those two packets
crossed each other on the wire, that may lead to diverging
bitmaps.

  This never happens in a well-tuned-system. In a well-tuned-
  system the resync controller has reduced the resync speed
  to zero long before we got into ahead-mode.

But we have to be prepared for the not-well-tuned-system
of course as well.
Because -> diverging bitmaps = non terminating resync.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

To improve the latency of IO requests during bitmap exchange,
we recently allowed writes while waiting for the bitmap, sending "set
out-of-sync" information packets for any newly dirtied bits.

We have to make sure that the new resync-uuid does not overtake
these "set oos" packets. Once the resync-uuid is received, the
sync target starts the resync process, and expects the bitmap to
only be cleared, not re-set.

If we use this protocol extension, we queue the generation and sending
of the resync-uuid on the worker, which naturally serializes with all
previously queued packets.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

When we set or clear bits in a bitmap page,
also set a flag in the page->private pointer.

This allows us to skip writes of unchanged pages.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The old name is confusing: the function does not increment anything.
Also rename _inc_ap_bio_cond to inc_ap_bio_cond: there is no need for
an underscore.
Finally, make it clear that these functions return boolean values.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The FAULT_ACTIVE macro just wraps the drbd_insert_fault macro for no
apparent reason.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

* C_STARTING_SYNC_S, C_STARTING_SYNC_T In these states the bitmap gets
  written to disk. Locking out of app-IO is done by using the
  drbd_queue_bitmap_io() and drbd_bitmap_io() functions these days.
  It is no longer necessary to lock out app-IO based on the connection
  state.
  App-IO that may come in after the BITMAP_IO flag got cleared before the
  state transition to C_SYNC_(SOURCE|TARGET) does not get mirrored, sets
  a bit in the local bitmap, that is already set, therefore changes nothing.

* C_WF_BITMAP_S In this state we send updates (P_OUT_OF_SYNC packets).
  With that we make sure they have the same number of bits when going
  into the C_SYNC_(SOURCE|TARGET) connection state.

* C_UNCONNECTED: The receiver starts, no need to lock out IO.

* C_DISCONNECTING: in drbd_disconnect() we had a wait_event()
  to wait until ap_bio_cnt reaches 0. Removed that.

* C_TIMEOUT, C_BROKEN_PIPE, C_NETWORK_FAILURE
  C_PROTOCOL_ERROR, C_TEAR_DOWN: Same as C_DISCONNECTING

* C_WF_REPORT_PARAMS: IO still possible since that is still
  like C_WF_CONNECTION.

And we do not need to send barriers in C_WF_BITMAP_S connection state.

Allow concurrent accesses to the bitmap when receiving the bitmap.
Everything gets ORed anyways.

A drbd_free_tl_hash() is in after_state_chg_work(). At that point
all the work items of the last connections must have been processed.

Introduced a call to drbd_free_tl_hash() into drbd_free_mdev()
for paranoia reasons.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

The condition must be checked after perpare_to_wait(). The old
implementaion could loose wakeup events. Never observed in real
life.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

We only issue resync requests if there is no significant application IO
going on. = Application IO has higher priority than resnyc IO.

If application IO can not be started because the resync process locked
an resync_lru entry, start the IO operations necessary to release the
lock ASAP.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

In this connection mode, the ahead node no longer replicates
application IO. The behind's disk becomes out dated.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

To ease tracking of bios in some hash tables, we want it to
not cross certain boundaries (128k, used to be 32k).
We limit the maximum bio size using queue parameters.

Historically some defines and variables we use there have been named
max_segment_size, which was misguided. Rename them to max_bio_size,
and use [blk_]queue_max_hw_sectors where appropriate.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Preparation patch to be able to use the auto-throttling resync controller
for online-verify requests as well.
Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>

Signed-off-by: NPhilipp Reisner <philipp.reisner@linbit.com>
Signed-off-by: NLars Ellenberg <lars.ellenberg@linbit.com>