Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 26 5月, 2011 1 次提交
    • P
      mmc: core: eMMC bus width may not work on all platforms · 08ee80cc
      由 Philip Rakity 提交于 
      CMD19 -- The offical way to validate bus widths from the JEDEC spec
does not work on all platforms.  Some platforms that use PCI/PCIe
to connect their SD controllers are known to fail.

If the quirk MMC_BUS_WIDTH_TEST is not defined we try to figure out
the bus width by reading the ext_csd at different bus widths and
compare this against the ext_csd read in 1 bit mode.  If no ext_csd
is available we default to 1 bit operations.

Code has been tested on mmp2 against 8 bit eMMC and Transcend 2GB
card that is known to not work in 4 bit mode.  The physical pins
on the card are not present to support 4 bit operation.
Signed-off-by: NPhilip Rakity <prakity@marvell.com>
Signed-off-by: NChris Ball <cjb@laptop.org>
      08ee80cc
  3. 25 5月, 2011 5 次提交
  5. 31 3月, 2011 1 次提交
  7. 17 3月, 2011 1 次提交
  9. 16 3月, 2011 1 次提交
    • C
      mmc: export eMMC4.4 enhanced area details to sysfs · 709de99d
      由 Chuanxiao Dong 提交于 
      Enhanced area feature is a new feature defined in eMMC4.4 standard. This
user data area provides higher performance/reliability, at the expense
of using twice the effective media space due to the area using SLC.

The MMC driver now reads out the enhanced area offset and size and adds
them to the device attributes in sysfs. Enabling the enhanced area can
only be done once, and should be done in manufacturing. To use this
feature, bit ERASE_GRP_DEF should also be set.

Documentation/ABI/testing/sysfs-devices-mmc describes the two new
attributes.
Signed-off-by: NChuanxiao Dong <chuanxiao.dong@intel.com>
Reviewed-by: NChris Ball <cjb@laptop.org>
Signed-off-by: NChris Ball <cjb@laptop.org>
      709de99d
  11. 09 1月, 2011 4 次提交
  13. 08 11月, 2010 1 次提交
  15. 23 10月, 2010 5 次提交
  17. 12 8月, 2010 1 次提交
    • A
      mmc: add erase, secure erase, trim and secure trim operations · dfe86cba
      由 Adrian Hunter 提交于 
      SD/MMC cards tend to support an erase operation.  In addition, eMMC v4.4
cards can support secure erase, trim and secure trim operations that are
all variants of the basic erase command.

SD/MMC device attributes "erase_size" and "preferred_erase_size" have been
added.

"erase_size" is the minimum size, in bytes, of an erase operation.  For
MMC, "erase_size" is the erase group size reported by the card.  Note that
"erase_size" does not apply to trim or secure trim operations where the
minimum size is always one 512 byte sector.  For SD, "erase_size" is 512
if the card is block-addressed, 0 otherwise.

SD/MMC cards can erase an arbitrarily large area up to and
including the whole card.  When erasing a large area it may
be desirable to do it in smaller chunks for three reasons:

    1. A single erase command will make all other I/O on the card
       wait.  This is not a problem if the whole card is being erased, but
       erasing one partition will make I/O for another partition on the
       same card wait for the duration of the erase - which could be a
       several minutes.

    2. To be able to inform the user of erase progress.

    3. The erase timeout becomes too large to be very useful.
       Because the erase timeout contains a margin which is multiplied by
       the size of the erase area, the value can end up being several
       minutes for large areas.

"erase_size" is not the most efficient unit to erase (especially for SD
where it is just one sector), hence "preferred_erase_size" provides a good
chunk size for erasing large areas.

For MMC, "preferred_erase_size" is the high-capacity erase size if a card
specifies one, otherwise it is based on the capacity of the card.

For SD, "preferred_erase_size" is the allocation unit size specified by
the card.

"preferred_erase_size" is in bytes.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Acked-by: NJens Axboe <axboe@kernel.dk>
Cc: Kyungmin Park <kmpark@infradead.org>
Cc: Madhusudhan Chikkature <madhu.cr@ti.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ben Gardiner <bengardiner@nanometrics.ca>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      dfe86cba
  19. 11 8月, 2010 2 次提交
  21. 30 3月, 2010 1 次提交
    • T
      include cleanup: Update gfp.h and slab.h includes to prepare for breaking... · 5a0e3ad6
      由 Tejun Heo 提交于 
      include cleanup: Update gfp.h and slab.h includes to prepare for breaking implicit slab.h inclusion from percpu.h

percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files.  percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.

percpu.h -> slab.h dependency is about to be removed.  Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability.  As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.

  http://userweb.kernel.org/~tj/misc/slabh-sweep.py

The script does the followings.

* Scan files for gfp and slab usages and update includes such that
  only the necessary includes are there.  ie. if only gfp is used,
  gfp.h, if slab is used, slab.h.

* When the script inserts a new include, it looks at the include
  blocks and try to put the new include such that its order conforms
  to its surrounding.  It's put in the include block which contains
  core kernel includes, in the same order that the rest are ordered -
  alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
  doesn't seem to be any matching order.

* If the script can't find a place to put a new include (mostly
  because the file doesn't have fitting include block), it prints out
  an error message indicating which .h file needs to be added to the
  file.

The conversion was done in the following steps.

1. The initial automatic conversion of all .c files updated slightly
   over 4000 files, deleting around 700 includes and adding ~480 gfp.h
   and ~3000 slab.h inclusions.  The script emitted errors for ~400
   files.

2. Each error was manually checked.  Some didn't need the inclusion,
   some needed manual addition while adding it to implementation .h or
   embedding .c file was more appropriate for others.  This step added
   inclusions to around 150 files.

3. The script was run again and the output was compared to the edits
   from #2 to make sure no file was left behind.

4. Several build tests were done and a couple of problems were fixed.
   e.g. lib/decompress_*.c used malloc/free() wrappers around slab
   APIs requiring slab.h to be added manually.

5. The script was run on all .h files but without automatically
   editing them as sprinkling gfp.h and slab.h inclusions around .h
   files could easily lead to inclusion dependency hell.  Most gfp.h
   inclusion directives were ignored as stuff from gfp.h was usually
   wildly available and often used in preprocessor macros.  Each
   slab.h inclusion directive was examined and added manually as
   necessary.

6. percpu.h was updated not to include slab.h.

7. Build test were done on the following configurations and failures
   were fixed.  CONFIG_GCOV_KERNEL was turned off for all tests (as my
   distributed build env didn't work with gcov compiles) and a few
   more options had to be turned off depending on archs to make things
   build (like ipr on powerpc/64 which failed due to missing writeq).

   * x86 and x86_64 UP and SMP allmodconfig and a custom test config.
   * powerpc and powerpc64 SMP allmodconfig
   * sparc and sparc64 SMP allmodconfig
   * ia64 SMP allmodconfig
   * s390 SMP allmodconfig
   * alpha SMP allmodconfig
   * um on x86_64 SMP allmodconfig

8. percpu.h modifications were reverted so that it could be applied as
   a separate patch and serve as bisection point.

Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: NTejun Heo <tj@kernel.org>
Guess-its-ok-by: NChristoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
      5a0e3ad6
  23. 25 3月, 2010 1 次提交
    • A
      mmc: fix incorrect interpretation of card type bits · 7198f3c9
      由 Adrian Hunter 提交于 
      In the extended CSD register the CARD_TYPE is an 8-bit value of which the
upper 6 bits were reserved in JEDEC specifications prior to version 4.4.
In version 4.4 two of the reserved bits were designated for identifying
support for the newly added High-Speed Dual Data Rate.  Unfortunately the
mmc_read_ext_csd() function required that the reserved bits be zero
instead of ignoring them as it should.

This patch makes mmc_read_ext_csd() ignore the CARD_TYPE bits that are
reserved or not yet supported.  It also stops the function jumping to the
end as though an error occurred, when it is only warns that the CARD_TYPE
bits (that it does interpret) are invalid.
Signed-off-by: NAdrian Hunter <adrian.hunter@nokia.com>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      7198f3c9
  25. 12 1月, 2010 1 次提交
  27. 16 12月, 2009 1 次提交
    • B
      mmc: add module parameter to set whether cards are assumed removable · bd68e083
      由 Ben Hutchings 提交于 
      Some people run general-purpose distribution kernels on netbooks with
a card that is physically non-removable or logically non-removable
(e.g. used for /home) and cannot be cleanly unmounted during suspend.
Add a module parameter to set whether cards are assumed removable or
non-removable, with the default set by CONFIG_MMC_UNSAFE_RESUME.

In general, it is not possible to tell whether a card present in an MMC
slot after resume is the same that was there before suspend.  So there are
two possible behaviours, each of which will cause data loss in some cases:

CONFIG_MMC_UNSAFE_RESUME=n (default): Cards are assumed to be removed
during suspend.  Any filesystem on them must be unmounted before suspend;
otherwise, buffered writes will be lost.

CONFIG_MMC_UNSAFE_RESUME=y: Cards are assumed to remain present during
suspend.  They must not be swapped during suspend; otherwise, buffered
writes will be flushed to the wrong card.

Currently the choice is made at compile time and this allows that to be
overridden at module load time.
Signed-off-by: NBen Hutchings <ben@decadent.org.uk>
Cc: Wouter van Heyst <larstiq@larstiq.dyndns.org>
Cc: <linux-mmc@vger.kernel.org>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>
      bd68e083
  29. 23 9月, 2009 6 次提交
  31. 16 9月, 2009 1 次提交
  33. 09 4月, 2009 1 次提交
  35. 01 1月, 2009 1 次提交
  37. 15 7月, 2008 1 次提交
  39. 23 3月, 2008 1 次提交
  41. 18 10月, 2007 1 次提交
  43. 24 9月, 2007 2 次提交
    • D
      MMC core learns about SPI · af517150
      由 David Brownell 提交于 
      Teach the MMC/SD/SDIO core about using SPI mode.

 - Use mmc_host_is_spi() so enumeration works through SPI signaling
   and protocols, not just the native versions.

 - Provide the SPI response type flags with each request issued,
   including requests from the new lock/unlock code.

 - Understand that cmd->resp[0] and mmc_get_status() results for SPI
   return different values than for "native" MMC/SD protocol; this
   affects resetting, checking card lock status, and some others.

 - Understand that some commands act a bit differently ... notably:
     * OP_COND command doesn't return the OCR
     * APP_CMD status doesn't have an R1_APP_CMD analogue

Those changes required some new and updated primitives:

 - Provide utilities to access two SPI-only requests, and one
   request that wasn't previously needed:
     * mmc_spi_read_ocr() ... SPI only
     * mmc_spi_set_crc() ... SPI only (override by module parm)
     * mmc_send_cid() ... for use without broadcast mode

 - Updated internal routines:
     * Previous mmc_send_csd() modified into mmc_send_cxd_native();
       it uses native "R2" responses, which include 16 bytes of data.
     * Previous mmc_send_ext_csd() becomes new mmc_send_cxd_data()
       helper for command-and-data access
     * Bugfix to that mmc_send_cxd_data() code:  dma-to-stack is
       unsafe/nonportable, so kmalloc a bounce buffer instead.

 - Modified mmc_send_ext_csd() now uses mmc_send_cxd_data() helper

 - Modified mmc_send_csd(), and new mmc_spi_send_cid(), routines use
   those helper routines based on whether they're native or SPI

The newest categories of cards supported by the MMC stack aren't expected
to work yet with SPI:  MMC or SD cards with over 4GB data, and SDIO.
All those cards support SPI mode, so eventually they should work too.
Signed-off-by: NDavid Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      af517150
    • P
      mmc: replace BUG_ON with WARN_ON · d84075c8
      由 Pierre Ossman 提交于 
      Replace all cases of BUG_ON with WARN_ON where there is a chance
(with varying degrees of slim) that the kernel can continue without
incidence.
Signed-off-by: NPierre Ossman <drzeus@drzeus.cx>
      d84075c8