Make this a named struct rather than an anonymous one,
we'll want to refer to it by name later.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Move the rt status checking to the start of the resume flow in order
to avoid sending D0I3_END_CMD to the FW.  Also, collect dump if an
assert was encountered.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Debug data dump is not working in flows that stop the device is used
in their error handling. During these flows the op mode mutex is
locked until the device stops.  Because of that, any assert generated
from the firmware can be handled only after the device already
stopped.

Since dumping cannot occour after stopping the device, split the the
dump function to two parts, Part that handles locking, and the part
that starts the actual dumping and call the second part in the op mode
stop device function.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Currently in case of DCM with P2P GO where BSS DTIM interval < 220 msec
the fw fails to allocate events for the P2P GO dtim due to long passive
scan events.

Fix this by requesting all scans in this scenario to be fragmented with
fast balance scan time settings.  The only exception is in case
fragmented scan was planned to be set due to low latency or high
throughput reason, set the scan timing as planned.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fast balance scan is similar to SCAN_TYPE_MILD, but this scan is
fragmented and has shorter out of operating channel time,
and therefore better match low latency scenarios.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In the past, we needed to program the keys when entering D3. This was
since we replaced the image. However, now that there is a single
image, this is no longer needed.  Note that RSC is sent separately in
a new command.  This solves issues with newer devices that support PN
offload. Since driver re-sent the keys, the PN got zeroed and the
receiver dropped the next packets, until PN caught up again.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NYisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.

Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Change MCC update response API to be compatible with new FW API.
While at it change v2 which is not in use anymore to v3 and cleanup
mcc_update v1 command and response which is obsolete.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Trigger dump collection if the alive flow fails, regardless of the
reason.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In mac80211, the default remains for HT, so set the limit to
HE for our driver.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For SU/SU-ER/MU PPDUs we have spatial reuse.

For those where it's relevant we also know the pre-FEC
padding factor, PE disambiguity bit, beam change bit
and doppler bit.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add information about the LDCP extra symbol segment to the HE
data when applicable (not for trigger-based PPDUs).

While at it, clean up the code for UL/DL a bit.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We have this data available, so add it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This code gets shorter if it doesn't have to check all the
conditions, so move it to an appropriate place that has all
of them validated already.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Split the code out into a separate routine, and move that to be
called inside the previously introduced iwl_mvm_decode_he_phy_data()
function.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Pull some of the decoding of he_phy_data into a separate function so
we don't need to check over and over again if it's valid.

While at it, fix the UL/DL bit reporting to be for all but trigger-
based frames.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As detected by Luca during code review when I move this in the
next patch, the code here is putting the data into the wrong
field (flags1 instead of flags2). Fix that.

Fixes: e5721e3f ("iwlwifi: mvm: add radiotap data for HE")
Reported-by: NLuca Coelho <luciano.coelho@intel.com>
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Remove a stray empty line, unbreak some lines that aren't
really that long, and move on variable setting into the
initializer to avoid initializing it twice.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

This is equivalent to checking he_phy_data != HE_PHY_DATA_INVAL,
which is already done in a number of places, so remove the extra
'overload' variable entirely.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Fix a bug that happens in the following scenario:
1) suspend without WoWLAN
2) mac80211 calls drv_stop because of the suspend
3) __iwl_mvm_mac_stop deallocates the aux station
4) during drv_stop the firmware crashes
5) iwlmvm:
	* sets IWL_MVM_STATUS_HW_RESTART_REQUESTED
	* asks mac80211 to kick the restart flow
6) mac80211 puts the restart worker into a freezable
   queue which means that the worker will not run for now
   since the workqueue is already frozen
7) ...
8) resume
9) mac80211 runs ieee80211_reconfig as part of the resume
10) mac80211 detects that a restart flow has been requested
    and that we are now resuming from suspend and cancels
    the restart worker
11) mac80211 calls drv_start()
12) __iwl_mvm_mac_start checks that IWL_MVM_STATUS_HW_RESTART_REQUESTED
    clears it, sets IWL_MVM_STATUS_IN_HW_RESTART and calls
    iwl_mvm_restart_cleanup()
13) iwl_fw_error_dump gets called and accesses the device
    to get debug data
14) iwl_mvm_up adds the aux station
15) iwl_mvm_add_aux_sta() allocates an internal station for
    the aux station
16) iwl_mvm_allocate_int_sta() tests IWL_MVM_STATUS_IN_HW_RESTART
    and doesn't really allocate a station ID for the aux
    station
17) a new queue is added for the aux station

Note that steps from 5 to 9 aren't really part of the
problem but were described for the sake of completeness.

Once the iwl_mvm_mac_stop() is called, the device is not
accessible, meaning that step 12) can't succeed and we'll
see the following:

drivers/net/wireless/intel/iwlwifi/pcie/trans.c:2122 iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]()
Timeout waiting for hardware access (CSR_GP_CNTRL 0x080403d8)
Call Trace:
[<ffffffffc03e6ad3>] iwl_trans_pcie_grab_nic_access+0xc0/0x1d6 [iwlwifi]
[<ffffffffc03e6a13>] iwl_trans_pcie_dump_regs+0x3fd/0x3fd [iwlwifi]
[<ffffffffc03dad42>] iwl_fw_error_dump+0x4f5/0xe8b [iwlwifi]
[<ffffffffc04bd43e>] __iwl_mvm_mac_start+0x5a/0x21a [iwlmvm]
[<ffffffffc04bd6d2>] iwl_mvm_mac_start+0xd4/0x103 [iwlmvm]
[<ffffffffc042d378>] drv_start+0xa1/0xc5 [iwl7000_mac80211]
[<ffffffffc045a339>] ieee80211_reconfig+0x145/0xf50 [mac80211]
[<ffffffffc044788b>] ieee80211_resume+0x62/0x66 [mac80211]
[<ffffffffc0366c5b>] wiphy_resume+0xa9/0xc6 [cfg80211]

The station id of the aux station is set to 0xff in step 3
and because we don't really allocate a new station id for
the auxliary station (as explained in 16), we end up sending
a command to the firmware asking to connect the queue
to station id 0xff. This makes the firmware crash with the
following information:

0x00002093 | ADVANCED_SYSASSERT
0x000002F0 | trm_hw_status0
0x00000000 | trm_hw_status1
0x00000B38 | branchlink2
0x0001978C | interruptlink1
0x00000000 | interruptlink2
0xFF080501 | data1
0xDEADBEEF | data2
0xDEADBEEF | data3
Firmware error during reconfiguration - reprobe!
FW error in SYNC CMD SCD_QUEUE_CFG

Fix this by clearing IWL_MVM_STATUS_HW_RESTART_REQUESTED
in iwl_mvm_mac_stop(). We won't be able to collect debug
data anyway and when we will brought up again, we will
have a clean state from the firmware perspective.
Since we won't have IWL_MVM_STATUS_IN_HW_RESTART set in
step 12) we won't get to the 2093 ASSERT either.

Fixes: bf8b286f ("iwlwifi: mvm: defer setting IWL_MVM_STATUS_IN_HW_RESTART")
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The triplet of get trigger, is trigger enabled and is trigger stopped
repeats itself.  Group them in a function to avoid code duplication.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Allow the FW to reorder HB channels and first scan HB channels with
assumed APs, in order to reduce the scan duration.

Currently enable it for all scan requests types.
Signed-off-by: NAyala Beker <ayala.beker@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The debug variables are bloating the iwl_fw struct.  And the fields
are out of order, missing docs and some are redundant.

Clean this up.  This serves as preparation for unionizing it for the
new ini infra.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When reading the profiles from the EWRD table in ACPI, we loop over
the data and set it into our internal table.  We use the number of
profiles specified in ACPI without checking its validity, so if the
ACPI table is corrupted and the number is larger than our array size,
we will try to make an out-of-bounds access.

Fix this by making sure the value specified in the ACPI table is
valid.

Fixes: 69964905 ("iwlwifi: mvm: add support for EWRD (Dynamic SAR) ACPI table")
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Support for setting keys for TKIP cipher suite was mistakenly removed
for AP mode. Fix this.

Fixes: 85aeb58c ("iwlwifi: mvm: Enable security on new TX API")
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As a temporary stage in the 22560 devices bring up, we disabled
power save, to avoid bugs related to that domain.
Now we would like to use power save so enable the balanced mode,
and allow configuring the mode via module parameter.
Signed-off-by: NGolan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We no longer want to consider the RSSI if the beacon / probe
has been heard on an adjacent channel.
This was based on a firmware capability that is now
unavailable.
Signed-off-by: NEmmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

The new coex schema requires setting the non-shared antenna
for the single_stream_ant_msk field in the TLC command.
Signed-off-by: NErel Geron <erelx.geron@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When operating as a soft ap with wep security, the key was not
configured to the fw for the stations, based on the fact that the
key will be specified in the tx command.

However, in the new tx api the tx command does not include the key,
which resulted in all data frames going out un-encrypted.

Fix it by configuring the key for all the stations as they are added.
Signed-off-by: NAvraham Stern <avraham.stern@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Current FIFO size calculation is wrong for two reasons:
- We access lmac 0 by default
- We don't take 11ax into consideration.
Fix both.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Since AMSDUs are not de-aggregated by HW in monitor mode,
we still need the option for setting large RBs (up to 12K).
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Make the adjustments for gen2 TX and RX of TKIP packets.  Strip MIC on
RX.  Don't add IV space and keep the MIC space zeroed on TX.

Devices that support gen2 data path support TKIP only in station mode.
In all other modes, fall back to SW encryption. Do this early in the
set_key() callback so that the key flags would not be incorrectly set.
Signed-off-by: NDavid Spinadel <david.spinadel@intel.com>
Signed-off-by: NIlan Peer <ilan.peer@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: NLiad Kaufman <liad.kaufman@intel.com>
Signed-off-by: NIdo Yariv <idox.yariv@intel.com>
Signed-off-by: NShaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

CDB support has nothing to do with non unified image.
Signed-off-by: NHaim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Alexei's patch, assumed that all versions of "struct iwl_error_event_table"
are the same, but there are really different versions in different files.

Rather than trying to fix this, or splitting the tracepoint, or anything of
the sort, just remove it entirely - turns out that nobody really uses it.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

We already report the RU offset, so we'd better also
report that we know the value.

Fixes: e5721e3f ("iwlwifi: mvm: add radiotap data for HE")
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>