buff should be freed before returning with SCSI_DH_RETRY in alua_rtpg().
Signed-off-by: Ntang.junhui <tang.junhui@zte.com.cn>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Not every device will return a useable VPD identification, but still
might support ALUA. Rather than disable ALUA support we should be
allowing the device identification to be empty and attach individual
ALUA device handler to each devices.

[mkp: Fixed typo reported by Bart]
Reported-by: NPaul Mackerras <paulus@ozlabs.org>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Tested-by: NPaul Mackerras <paulus@ozlabs.org>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

It's possible to use "err" without initializing it.  If it happens to be
a 2 which is SCSI_DH_RETRY then that could cause a bug.  Bart Van Assche
pointed out that we should probably re-initialize it for every iteration
through the retry loop.
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NJames Bottomley <jejb@linux.vnet.ibm.com>

This patch avoids that building with W=1 causes gcc to report the
following type of warning:

    no previous prototype for ... [-Wmissing-prototypes]
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Ewan Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

While retesting the SRP initiator I ran the command "rmmod mlx4_ib"
while I/O was in progress. That command triggers SCSI device removal
indirectly. Avoid that this action triggers the following deadlock:

=================================
[ INFO: inconsistent lock state ]
4.6.0-rc0-dbg+ #2 Tainted: G           O
---------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
multipathd/484 [HC0[0]:SC0[0]:HE1:SE1] takes:
 (&(&pg->lock)->rlock){+.?...}, at: [<ffffffffa04f50a2>] alua_bus_detach+0x52/0xa0 [scsi_dh_alua]
{IN-SOFTIRQ-W} state was registered at:
  [<ffffffff810a64a9>] __lock_acquire+0x7e9/0x1ad0
  [<ffffffff810a7fd0>] lock_acquire+0x60/0x80
  [<ffffffff8159910e>] _raw_spin_lock_irqsave+0x3e/0x60
  [<ffffffffa04f5131>] alua_rtpg_queue+0x41/0x1d0 [scsi_dh_alua]
  [<ffffffffa04f5531>] alua_check+0xe1/0x220 [scsi_dh_alua]
  [<ffffffffa04f5709>] alua_check_sense+0x99/0xb0 [scsi_dh_alua]
  [<ffffffff813f0d01>] scsi_check_sense+0x71/0x3f0
  [<ffffffff813f2f8b>] scsi_decide_disposition+0x18b/0x1d0
  [<ffffffff813f6e52>] scsi_softirq_done+0x52/0x140
  [<ffffffff812a26f2>] blk_done_softirq+0x52/0x90
  [<ffffffff8105bc1f>] __do_softirq+0x10f/0x230
  [<ffffffff8105bec8>] irq_exit+0xa8/0xb0
  [<ffffffff8101a675>] do_IRQ+0x65/0x110
  [<ffffffff8159a2c9>] ret_from_intr+0x0/0x19
  [<ffffffff811732f1>] kmem_cache_alloc+0x151/0x190
  [<ffffffff8118e534>] create_object+0x34/0x2d0
  [<ffffffff8158eaa6>] kmemleak_alloc_percpu+0x56/0xd0
  [<ffffffff8113ab0d>] pcpu_alloc+0x38d/0x660
  [<ffffffff8113aded>] __alloc_percpu_gfp+0xd/0x10
  [<ffffffff812e56a5>] __percpu_counter_init+0x55/0xb0
  [<ffffffff812b4989>] blkg_alloc+0x79/0x230
  [<ffffffff812b6756>] blkcg_init_queue+0x26/0x1d0
  [<ffffffff81297eed>] blk_alloc_queue_node+0x27d/0x2e0
  [<ffffffffa017766c>] dm_create+0x20c/0x570 [dm_mod]
  [<ffffffffa017e356>] dev_create+0x56/0x2c0 [dm_mod]
  [<ffffffffa017dcae>] ctl_ioctl+0x26e/0x520 [dm_mod]
  [<ffffffffa017df6e>] dm_ctl_ioctl+0xe/0x20 [dm_mod]
  [<ffffffff811aa8ee>] do_vfs_ioctl+0x8e/0x660
  [<ffffffff811aaefc>] SyS_ioctl+0x3c/0x70
  [<ffffffff81599929>] entry_SYSCALL_64_fastpath+0x1c/0xac
irq event stamp: 4290931
hardirqs last  enabled at (4290931): [ 1662.892772]
[<ffffffff81599341>] _raw_spin_unlock_irqrestore+0x31/0x50
hardirqs last disabled at (4290930): [<ffffffff815990e7>] _raw_spin_lock_irqsave+0x17/0x60
softirqs last  enabled at (4290774): [<ffffffff8105bcdb>] __do_softirq+0x1cb/0x230
softirqs last disabled at (4289831): [<ffffffff8105bec8>] irq_exit+0xa8/0xb0

other info that might help us debug this:
 Possible unsafe locking scenario:

       CPU0
       ----
  lock(&(&pg->lock)->rlock);
  <Interrupt>
    lock(&(&pg->lock)->rlock);

 *** DEADLOCK ***

2 locks held by multipathd/484:
 #0:  (&bdev->bd_mutex){+.+.+.}, at: [<ffffffff811d1cc3>] __blkdev_put+0x33/0x360
 #1:  (sd_ref_mutex){+.+...}, at: [<ffffffff81400afc>] scsi_disk_put+0x1c/0x40

stack backtrace:
CPU: 6 PID: 484 Comm: multipathd Tainted: G           O    4.6.0-rc0-dbg+ #2
Call Trace:
 [<ffffffff812bd115>] dump_stack+0x67/0x92
 [<ffffffff810a5175>] print_usage_bug+0x215/0x240
 [<ffffffff810a56ea>] mark_lock+0x54a/0x610
 [<ffffffff810a6505>] __lock_acquire+0x845/0x1ad0
 [<ffffffff810a7fd0>] lock_acquire+0x60/0x80
 [<ffffffff81598f23>] _raw_spin_lock+0x33/0x50
 [<ffffffffa04f50a2>] alua_bus_detach+0x52/0xa0 [scsi_dh_alua]
 [<ffffffff813ff6f7>] scsi_dh_release_device+0x17/0x50
 [<ffffffff813fb8da>] scsi_device_dev_release_usercontext+0x2a/0x120
 [<ffffffff810701f0>] execute_in_process_context+0x80/0x90
 [<ffffffff813fb8a7>] scsi_device_dev_release+0x17/0x20
 [<ffffffff813c8cfd>] device_release+0x2d/0x90
 [<ffffffff812bfa8a>] kobject_release+0x7a/0x190
 [<ffffffff812bf946>] kobject_put+0x26/0x50
 [<ffffffff813c8ee2>] put_device+0x12/0x20
 [<ffffffff813edc86>] scsi_device_put+0x26/0x30
 [<ffffffff81400b0d>] scsi_disk_put+0x2d/0x40
 [<ffffffff81400b68>] sd_release+0x48/0xb0
 [<ffffffff811d1f2e>] __blkdev_put+0x29e/0x360
 [<ffffffff811d24b9>] blkdev_put+0x49/0x170
 [<ffffffff811d2600>] blkdev_close+0x20/0x30
 [<ffffffff81198f48>] __fput+0xe8/0x1f0
 [<ffffffff81199089>] ____fput+0x9/0x10
 [<ffffffff81075d9e>] task_work_run+0x6e/0xa0
 [<ffffffff81001119>] exit_to_usermode_loop+0xa9/0xb0
 [<ffffffff81001590>] syscall_return_slowpath+0xb0/0xc0
 [<ffffffff815999b7>] entry_SYSCALL_64_fastpath+0xaa/0xac

Fixes: cb0a168c (scsi_dh_alua: update 'access_state' field)
Cc: Hannes Reinecke <hare@suse.de>
Signed-off-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NLaurence Oberman <loberman@redhat.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The pg_updated variable is support to be set to false at the start but
it is uninitialized.

Fixes: cb0a168c ('scsi_dh_alua: update 'access_state' field')
Signed-off-by: NDan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: NHannes Reinicke <hare@suse.de>
Reviewed-by: NManoj Kumar <manoj@linux.vnet.ibm.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Track attached SCSI devices and update the 'access_state' field whenever
an ALUA state change has been detected.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

scsi_proto.h now contains definitions for the ALUA state, so we don't
have to carry them in the device handler.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NBart van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

[mkp: Fixed merge due to patches 20-22 of series being postponed]
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If a device needs to be rescanned the device_handler might need
to be rechecked, too.
So add a 'rescan' callback to the device handler and call it
upon scsi_rescan_device(). The rescan callback will be invoked
from the Unit Attention handling of ASC/ASCQ 3F 03
(INQUIRY DATA HAS CHANGED).
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Sending a 'REPORT TARGET PORT GROUP' command is a costly operation,
as the array has to gather information about all ports.
So instead of using RTPG to poll for a status update when a port
is in transitioning we should be sending a TEST UNIT READY, and
wait for the sense code to report success.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When we read in the target port group state we should be
updating all affected port groups, otherwise we risk
running out of sync.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When we receive a unit attention code of 'ALUA state changed'
we should recheck the state, as it might be due to an implicit
ALUA state transition. This allows us to return NEEDS_RETRY
instead of ADD_TO_MLQUEUE, allowing to terminate the retries
after a certain time.
At the same time a workqueue item might already be queued, which
should be started immediately to avoid any delays.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Add a new blacklist flag BLIST_SYNC_ALUA to instruct the
alua device handler to use synchronous command submission
for ALUA commands.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Some arrays may only capable of handling one STPG at a time,
so this patch adds a singlethreaded workqueue for STPGs to be
submitted synchronously.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The current ALUA device_handler has two drawbacks:
- We're sending a 'SET TARGET PORT GROUP' command to every LUN,
  disregarding the fact that several LUNs might be in a port group
  and will be automatically switched whenever _any_ LUN within
  that port group receives the command.
- Whenever a LUN is in 'transitioning' mode we cannot block I/O
  to that LUN, instead the controller has to abort the command.
  This leads to increased traffic across the wire and heavy load
  on the controller during switchover.

With this patch the RTPG handling is moved to a per-portgroup
workqueue. This reduces the number of 'REPORT TARGET PORT GROUP'
and 'SET TARGET PORT GROUPS' sent to the controller as we're sending
them now per port group, and not per device as previously.
It also allows us to block I/O to any LUN / port group found to be
in 'transitioning' ALUA mode, as the workqueue item will be requeued
until the controller moves out of transitioning.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The 'relative port' field is not used, and might get stale when
the port group changes. So remove the field altogether.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

When the optimize_stpg module option is set we should just set it
once during port_group allocation. Doing so allows us to override
it later with device specific settings.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

revert commit a8e5a2d5 ("[SCSI] scsi_dh_alua: ALUA handler attach should succeed while TPG is transitioning")

This reverts commit a8e5a2d5

Obsoleted by the next patch.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Rework alua_check_vpd() to use scsi_vpd_get_tpg()
and move the port group selection into the function, too.
With that we can simplify alua_initialize() to just
call alua_check_tpgs() and alua_check_vpd();
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use scsi_vpd_lun_id() to assign a unique device identification
to the alua port group structure.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The port group needs to be a separate structure as several
LUNs might belong to the same group.
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The RTPG buffer will only evaluated within alua_rtpg(),
so we can allocate it locally there and avoid having to
put it into the global structure.
Reviewed-by: NEwan Milne <emilne@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

All commands are issued synchronously, so no need to open-code
scsi_execute_req_flags() anymore. And we can get rid of the
static sense code structure element. scsi_execute_req_flags()
will be setting REQ_QUIET and REQ_PREEMPT, but that is
perfectly fine as we're evaluating and logging any errors
ourselves and we really need to send the command even if
the device is quiesced.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

If the call to SET TARGET PORT GROUPS fails we have no idea what
state the array is left in, so we need to issue a call to
REPORT TARGET PORT GROUPS in these cases.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The 'activate_complete' function needs to be executed after
stpg has finished, so we can as well execute stpg synchronously
and call the function directly.
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Separate out SET TARGET PORT GROUP functionality into a separate
function alua_stpg().
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Pass in the buffer as a function argument for submit_rtpg().
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Signed-off-by: NHannes Reinecke <hare@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

With commit 83ea0e5e ("scsi_dh_alua: use scsi_vpd_tpg_id()") these
variables became obsolete, but weren't removed.

[mkp: Fixed checkpatch warning]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use the common function 'scsi_vpd_tpg_id()' instead of open-coding
it in scsi_dh_alua.

[mkp: Applied by hand]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Most sense code is already handled in the generic
code, so we shouldn't be adding special cases here.
However, when doing so we need to check for
unit attention whenever we're sending an internal
command.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Instead of returning an error code in alua_check_tpgs() we should
rather return the tpgs mode directly and have a cleaner syntax.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use 'get_unaligned_XX' and 'put_unaligned_XX' instead of
open-coding it.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

We should be using a flag when RTPG extended header is not
supported, that saves us sending RTPG twice for older arrays.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NBart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fixup copy-and-paste error in the description of stpg_endio().
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Fixup submit_rtpg() to always return a standard SCSI return code.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Use standard logging functions instead of hand-crafted ones.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NEwan Milne <emilne@redhat.com>
Reviewed-by: NBart Van Assche <bvanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The only check for a valid sense code is calling scsi_normalize_sense()
and check the return value. So drop the pointless checks and rely on
scsi_normalize_sense() to figure out if the sense code is valid.
With that we can also remove the 'senselen' field.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.com>
Reviewed-by: NBart van Assche <bvanassche@sandisk.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

Issue different logging messages if ALUA is not supported
or the TPGS setting is invalid.
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>

The SCSI device now has the VPD page 0x83 information attached,
so there is no need to query it again.

[mkp: Fixed a checkpatch warning]
Signed-off-by: NHannes Reinecke <hare@suse.de>
Reviewed-by: NMartin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: NChristoph Hellwig <hch@lst.de>
Reviewed-by: NJohannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: NMartin K. Petersen <martin.petersen@oracle.com>