This is a Qualcomm based device with a QMI function on interface 4.
It is mode switched from 2020:2030 using a standard eject message.

T:  Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#=  6 Spd=480  MxCh= 0
D:  Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs=  1
P:  Vendor=2020 ProdID=2031 Rev= 2.32
S:  Manufacturer=Mobile Connect
S:  Product=Mobile Connect
S:  SerialNumber=0123456789ABCDEF
C:* #Ifs= 6 Cfg#= 1 Atr=80 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=83(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=85(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=(none)
E:  Ad=87(I) Atr=03(Int.) MxPS=  10 Ivl=32ms
E:  Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E:  Ad=89(I) Atr=03(Int.) MxPS=   8 Ivl=32ms
E:  Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=(none)
E:  Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=125us

Cc: stable@vger.kernel.org
Signed-off-by: NBjørn Mork <bjorn@mork.no>
[ johan: use tabs to align comments in adjacent lines ]
Signed-off-by: NJohan Hovold <johan@kernel.org>

Lorenz Messtechnik has a device that is controlled by the cp210x driver,
so add the device id to the driver.  The device id was provided by
Silicon-Labs for the devices from this vendor.
Reported-by: NUli <t9cpu@web.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

if platform_driver_register fails, cleanup the allocated resource
gracefully.
Signed-off-by: NMukesh Ojha <mojha@codeaurora.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When the kernel is compiled with preemption enabled, the URB completion
handler can run in parallel with the work responsible for waking up the
tty layer. If the URB handler sets the EVENT_TTY_WAKEUP bit during the
call to tty_port_tty_wakeup() to signal that there is room for additional
input, it will be cleared at the end of this call. As a result, TX traffic
on the upper layer will be blocked.

This can be seen with a kernel configured with CONFIG_PREEMPT, and a fast
modem connected with PPP running over a USB CDC-ACM port.

Use test_and_clear_bit() instead, which ensures that each wakeup requested
by the URB completion code will trigger a call to tty_port_tty_wakeup().

Fixes: 1aba579f cdc-acm: handle read pipe errors
Signed-off-by: NRomain Izard <romain.izard.pro@gmail.com>
Cc: stable <stable@vger.kernel.org>
Acked-by: NOliver Neukum <oneukum@suse.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When EXTCON is a loadable module, mtu3 fails to link as built-in:

drivers/usb/mtu3/mtu3_plat.o: In function `mtu3_probe':
mtu3_plat.c:(.text+0x690): undefined reference to `extcon_get_edev_by_phandle'

Add a Kconfig dependency to force mtu3 also to be a loadable module
if extconn is, but still allow it to be built without extcon.

Fixes: d0ed062a ("usb: mtu3: dual-role mode support")
Signed-off-by: NArnd Bergmann <arnd@arndb.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

of_match_device in usb251xb_probe can fail and returns a NULL pointer.
The patch avoids a potential NULL pointer dereference in this scenario.
Signed-off-by: NAditya Pakki <pakki001@umn.edu>
Reviewed-by: NRichard Leitner <richard.leitner@skidata.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Some PHYs do not support PHY_MODE_USB_HOST_SS, i.e. USB 3.0 or higher.
Fall back and try the more generic PHY_MODE_USB_HOST if it fails.

Fixes: b97a3134 ("usb: core: comply to PHY framework")
Signed-off-by: NChen-Yu Tsai <wens@csie.org>
Tested-by: NNeil Armstrong <narmstrong@baylibre.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 2f31a67f ("usb: xhci: Prevent bus suspend if a port connect
change or polling state is detected") was intended to prevent ports that
were still link training from being forced to U3 suspend state mid
enumeration.
This solved enumeration issues for devices with slow link training.

Turns out some devices are stuck in the link training/polling state,
and thus that patch will prevent suspend completely for these devices.
This is seen with USB3 card readers in some MacBooks.

Instead of preventing suspend, give some time to complete the link
training. On successful training the port will end up as connected
and enabled.
If port instead is stuck in link training the bus suspend will continue
suspending after 360ms (10 * 36ms) timeout (tPollingLFPSTimeout).

Original patch was sent to stable, this one should go there as well

Fixes: 2f31a67f ("usb: xhci: Prevent bus suspend if a port connect change or polling state is detected")
Cc: stable@vger.kernel.org
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The xhci debug capability (DbC) feature did its memory cleanup with
spinlock held. dma_free_coherent() warns if called with interrupts
disabled

move the memory cleanup outside the spinlock

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

A suspended SS port in U3 link state will go to U0 when resumed, but
can almost immediately after that enter U1 or U2 link power save
states before host controller driver reads the port status.

Host controller driver only checks for U0 state, and might miss
the finished resume, leaving flags unclear and skip notifying usb
code of the wake.

Add U1 and U2 to the possible link states when checking for finished
port resume.

Cc: stable <stable@vger.kernel.org>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The write_parport_reg_nonblock() helper takes a reference to the struct
mos_parport, but failed to release it in a couple of error paths after
allocation failures, leading to a memory leak.

Johan said that move the kref_get() and mos_parport assignment to the
end of urbtrack initialisation is a better way, so move it. and
mos_parport do not used until urbtrack initialisation.
Signed-off-by: NLin Yi <teroincn@163.com>
Fixes: b69578df ("USB: usbserial: mos7720: add support for parallel port on moschip 7715")
Cc: stable <stable@vger.kernel.org>     # 2.6.35
Signed-off-by: NJohan Hovold <johan@kernel.org>

In f_hidg_write() the write_spinlock is acquired before calling
usb_ep_queue() which causes a deadlock when dummy_hcd is being used.
This is because dummy_queue() callbacks into f_hidg_req_complete() which
tries to acquire the same spinlock. This is (part of) the backtrace when
the deadlock occurs:

  0xffffffffc06b1410 in f_hidg_req_complete
  0xffffffffc06a590a in usb_gadget_giveback_request
  0xffffffffc06cfff2 in dummy_queue
  0xffffffffc06a4b96 in usb_ep_queue
  0xffffffffc06b1eb6 in f_hidg_write
  0xffffffff8127730b in __vfs_write
  0xffffffff812774d1 in vfs_write
  0xffffffff81277725 in SYSC_write

Fix this by releasing the write_spinlock before calling usb_ep_queue()
Reviewed-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: NJames Bottomley <James.Bottomley@HansenPartnership.com>
Cc: stable@vger.kernel.org # 4.11+
Fixes: 749494b6 ("usb: gadget: f_hid: fix: Move IN request allocation to set_alt()")
Signed-off-by: NRadoslav Gerganov <rgerganov@vmware.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Restore the status of ep->stopped in function net2272_dequeue().

When the given request is not found in the endpoint queue
the function returns -EINVAL without restoring the state of
ep->stopped. Thus the endpoint keeps blocked and does not transfer
any data anymore.

This fix is only compile-tested, since we do not have a
corresponding hardware. An analogous fix was tested in the sibling
driver. See "usb: gadget: net2280: Fix net2280_dequeue()"
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGuido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When a request must be dequeued with net2280_dequeue() e.g. due
to a device clear action and the same request is finished by the
function scan_dma_completions() then the function net2280_dequeue()
does not find the request in the following search loop and
returns the error -EINVAL without restoring the status ep->stopped.
Thus the endpoint keeps blocked and does not receive any data
anymore.
This fix restores the status and does not issue an error message.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGuido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The OUT endpoint normally blocks (NAK) subsequent packets when a
short packet was received and returns an incomplete queue entry to
the gadget driver. Thereby the gadget driver can detect a short packet
when reading queue entries with a length that is not equal to a
multiple of packet size.

The start_queue() function enables receiving OUT packets regardless of
the content of the OUT FIFO. This results in a race: With the current
code, it's possible that the "!ep->is_in && (readl(&ep->regs->ep_stat)
& BIT(NAK_OUT_PACKETS))" test in start_dma() will fail, then a short
packet will be received, and then start_queue() will call
stop_out_naking(). That's what we don't want (OUT naking gets turned
off while there is data in the FIFO) because then the next driver
request might receive a mixture of old and new packets.

With the patch, this race can't occur because the FIFO's state is
tested after we know that OUT naking is already turned on, and OUT
naking is stopped only when both of the conditions are met.  This
ensures that all received data is delivered to the gadget driver,
which can detect a short packet now before new packets are appended
to the last short packet.
Acked-by: NAlan Stern <stern@rowland.harvard.edu>
Signed-off-by: NGuido Kiener <guido.kiener@rohde-schwarz.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This patch simply adds a new PCI Device ID
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

There is no need to compare *port* with >= 0 because such comparison
of an unsigned value is always true.

Fix this by removing such comparison.

Addresses-Coverity-ID: 1443949 ("Unsigned compared against 0")
Fixes: 02a50b87 ("usb: usb251xb: add usb data lane port swap feature")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: NRichard Leitner <richard.leitner@skidata.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

There are cases where multiple device tree nodes point to the
same phy node by means of the "phys" property, but we should
only consider those nodes that are marked as available rather
than just any node.

Fixes: 98bfb394 ("usb: of: add an api to get dr_mode by the phy node")
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: NFabrizio Castro <fabrizio.castro@bp.renesas.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

PD 2.0 sinks are supposed to accept src-capabilities with a 3.0 header and
simply ignore any src PDOs which the sink does not understand such as PPS
but some 2.0 sinks instead ignore the entire PD_DATA_SOURCE_CAP message,
causing contract negotiation to fail.

This commit fixes such sinks not working by re-trying the contract
negotiation with PD-2.0 source-caps messages if we don't have a contract
after PD_N_HARD_RESET_COUNT hard-reset attempts.

The problem fixed by this commit was noticed with a Type-C to VGA dongle.
Signed-off-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

When plugging BUFFALO LUA4-U3-AGT USB3.0 to Gigabit Ethernet LAN
Adapter, warning messages filled up dmesg.

[  101.098287] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[  101.117463] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?
[  101.136513] xhci-hcd ee000000.usb: WARN Successful completion on short TX for slot 1 ep 4: needs XHCI_TRUST_TX_LENGTH quirk?

Adding the XHCI_TRUST_TX_LENGTH quirk resolves the issue.
Signed-off-by: NYasushi Asano <yasano@jp.adit-jv.com>
Signed-off-by: NSpyridon Papageorgiou <spapageorgiou@de.adit-jv.com>
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Currently there is no check on platform_get_irq() return value
in case it fails, hence never actually reporting any errors and
causing unexpected behavior when using such value as argument
for function regmap_irq_get_virq().

Fix this by adding a proper check, a message error and return
*irq* in case platform_get_irq() fails.

Addresses-Coverity-ID: 1443899 ("Improper use of negative value")
Fixes: d2061f9c ("usb: typec: add driver for Intel Whiskey Cove PMIC USB Type-C PHY")
Cc: stable@vger.kernel.org
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The SIMCom SIM5218 and compatible devices have 5 USB interfaces, only 4
of which are serial ports.  The fifth is a network interface supported
by the qmi-wwan driver.  Furthermore, the serial ports do not support
modem control signals.  Add driver_info flags to reflect this.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Fixes: ec0cd94d ("usb: option: add SIMCom SIM5218")
Cc: stable <stable@vger.kernel.org>	# 3.2
Signed-off-by: NJohan Hovold <johan@kernel.org>

Add PIDs for the NovaTech OrionLX+ and Orion I/O so they can be
automatically detected.
Signed-off-by: NGeorge McCollister <george.mccollister@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

The Quectel EM12 is a Cat. 12 LTE modem. It behaves in the exactly the
same way as the EP06 (including the dynamic configuration behavior), so
the same checks on reserved interfaces, etc. are needed.
Signed-off-by: NKristian Evensen <kristian.evensen@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NJohan Hovold <johan@kernel.org>

As all the memblock allocation functions return NULL in case of error
rather than panic(), the duplicates with _nopanic suffix can be removed.

Link: http://lkml.kernel.org/r/1548057848-15136-22-git-send-email-rppt@linux.ibm.comSigned-off-by: NMike Rapoport <rppt@linux.ibm.com>
Acked-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Reviewed-by: Petr Mladek <pmladek@suse.com>		[printk]
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: Christoph Hellwig <hch@lst.de>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Dennis Zhou <dennis@kernel.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Greentime Hu <green.hu@gmail.com>
Cc: Guan Xuetao <gxt@pku.edu.cn>
Cc: Guo Ren <guoren@kernel.org>
Cc: Guo Ren <ren_guo@c-sky.com>				[c-sky]
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Juergen Gross <jgross@suse.com>			[Xen]
Cc: Mark Salter <msalter@redhat.com>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Max Filippov <jcmvbkbc@gmail.com>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Paul Burton <paul.burton@mips.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Rich Felker <dalias@libc.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Rob Herring <robh@kernel.org>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Stafford Horne <shorne@gmail.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Vineet Gupta <vgupta@synopsys.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

This static inline is unnecessary and can be removed
by using the vsprintf %ph extension.

This reduces overall object size by more than 2K.
Reported-by: NLouis Taylor <louis@kragniz.eu>
Signed-off-by: NJoe Perches <joe@perches.com>
Reviewed-by: NLouis Taylor <louis@kragniz.eu>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Make the default autosuspend delay configurable at build time.
This is useful for systems that require a non-standard value as
it avoids relying on the command line being properly set.
Signed-off-by: NMans Rullgard <mans@mansr.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Add missing right parenthesis.
Signed-off-by: NJakub Wilk <jwilk@jwilk.net>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Refactor the code in charge of looking up the USB PHY when no platdata
is provided. Attempt to get a generic USB PHY first, then look for a
legacy USB PHY through device-tree and finally get any registered PHY
with the correct type.

This way, only a single USB PHY is obtained and the flow is easier to
understand and follow.

All error pointers (except for EPROBE_DEFER) are considered as PHY
not found.
Signed-off-by: NPaul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

According to the chipidea driver bindings, the USB PHY is specified via
the "phys" phandle node. However, this only takes effect for USB PHYs
that use the common PHY framework. For legacy USB PHYs, a simple lookup
based on the USB PHY type is done instead.

This does not play out well when more than one USB PHY is registered,
since the first registered PHY matching the type will always be
returned regardless of what the driver was bound to.

Fix this by looking up the PHY based on the "phys" phandle node.
Although generic PHYs are rather matched by their "phys-name" and not
the "phys" phandle directly, there is no helper for similar lookup on
legacy PHYs and it's probably not worth the effort to add it.

When no legacy USB PHY is found by phandle, fallback to grabbing any
registered USB2 PHY. This ensures backward compatibility if some users
were actually relying on this mechanism.
Signed-off-by: NPaul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch adds support to set the power line polarity for i.MX SoCs.

To let the USB controller control the power it may be necessary to
configure the polarity of the power line. So far the polarity was
configured by Bootloader or alternatively the power line was muxed
as gpio and driven by a regulator.

Also make use of of_property_read_bool.
Signed-off-by: NPhilipp Puschmann <philipp.puschmann@emlix.com>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Those 2 headers files are not required now.
Signed-off-by: NJun Li <jun.li@nxp.com>
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The ChipIdea's platform device need to be unregistered on Tegra's driver
module removal.

Fixes: dfebb5f4 ("usb: chipidea: Add support for Tegra20/30/114/124")
Signed-off-by: NDmitry Osipenko <digetx@gmail.com>
Acked-by: NPeter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

On Chrome OS we want to use USBguard to potentially limit access to USB
devices based on policy. We however to do not want to wait for userspace to
come up before initializing fixed USB devices to not regress our boot
times.

This patch adds option to instruct the kernel to only authorize devices
connected to the internal ports. Previously we could either authorize
all or none (or, by default, we'd only authorize wired devices).

The behavior is controlled via usbcore.authorized_default command line
option.
Signed-off-by: NDmitry Torokhov <dtor@chromium.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Commit 1a2f474d handles block _reads_ separately with plain-I2C
adapters, but the problem described with regmap-i2c not handling
SMBus block transfers (i.e. read and writes) correctly also exists
with writes.

As workaround, this patch adds a block write function the same way
1a2f474d adds a block read function.

Fixes: 1a2f474d ("usb: typec: tps6598x: handle block reads separately with plain-I2C adapters")
Fixes: 0a4c005b ("usb: typec: driver for TI TPS6598x USB Power Delivery controllers")
Signed-off-by: NNikolaus Voss <nikolaus.voss@loewensteinmedical.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: NGuenter Roeck <linux@roeck-us.net>
Acked-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

This fix enables USB role feature on intel commercial nuc
platform which is based on Kabylake chipset.
Signed-off-by: NBalaji Manoharan <m.balaji@intel.com>
Reviewed-by: NHans de Goede <hdegoede@redhat.com>
Reviewed-by: NHeikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Fix build warning when building drivers/usb/host/xhci-mem.o with W=1 due
to missing prototype for xhci_free_virt_devices_depth_first.

This function is only used in xhci-mem.c so just make it static.
Signed-off-by: NJean-Philippe Menil <jpmenil@gmail.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

Replaced "xhci_dbc_flush_reqests" with xhci_dbc_flush_requests".
Signed-off-by: NPrabhat Chand Pandey <prabhat.chand.pandey@intel.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

The member @parent of xhci_regset struct is not used in fact,
so remove it
Signed-off-by: NChunfeng Yun <chunfeng.yun@mediatek.com>
Signed-off-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>

During initialization, the host and super-speed power domains will
contain an ERR_PTR() encoded error code rather than being NULL. To
avoid a crash, use a !IS_ERR_OR_NULL() condition during cleanup.
Signed-off-by: NThierry Reding <treding@nvidia.com>
Fixes: 6494a9ad ("usb: xhci: tegra: Add genpd support")
Cc: stable <stable@vger.kernel.org>
Reviewed-by: NJon Hunter <jonathanh@nvidia.com>
Acked-by: NMathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>