There will be only one PHC clock per port. PTP should be enabled only on
one PF per port. The change enables PTP functionality on the PF that
initializes the port. The change is useful in multi-function modes e.g.,
NPAR where a port can have more than one PF.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Vlans are not getting removed when drivers are unloaded. The recent storm
firmware versions had added safeguards against re-configuring an already
configured vlan. As a result, PF inner reload flows (e.g., mtu change)
might trigger an assertion.
This change is going to remove vlans (same as we do for MACs) when doing
a chip cleanup during unload.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

On some customer setups it was observed that shmem contains a non-zero fip
MAC for 57711 which would lead to enabling of SW FCoE.
Add a software workaround to clear the bad fip mac address if no FCoE
connections are supported.
Signed-off-by: NSudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: NAriel Elior <ariel.elior@cavium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function hso_probe reads if_num from the USB device (as an u8) and uses
it without a length check to index an array, resulting in an OOB memory read
in hso_probe or hso_get_config_data.

Add a length check for both locations and updated hso_probe to bail on
error.

This issue has been assigned CVE-2018-19985.
Reported-by: NHui Peng <benquike@gmail.com>
Reported-by: NMathias Payer <mathias.payer@nebelwelt.net>
Signed-off-by: NHui Peng <benquike@gmail.com>
Signed-off-by: NMathias Payer <mathias.payer@nebelwelt.net>
Reviewed-by: NSebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: NGreg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If CONFIG_DEBUG_SHIRQ is enabled __free_irq() intentionally fires
a spurious interrupt. This interrupt causes a crash because
tp->dev->phydev is NULL at that time.

Fixes: 38caff5a ("r8169: handle all interrupt events in the hard irq handler")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

gcc warning this:

drivers/net/ieee802154/ca8210.c:730:10: warning:
 comparison is always false due to limited range of data type [-Wtype-limits]

'len' is u8 type, we get it from buf[1] adding 2, which can overflow.
This patch change the type of 'len' to unsigned int to avoid this,also fix
the gcc warning.

Fixes: ded845a7 ("ieee802154: Add CA8210 IEEE 802.15.4 device driver")
Signed-off-by: NYueHaibing <yuehaibing@huawei.com>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>

Previously we did not ensure tcp flags have a place to be stored
when using IPv6. We correct this by including IPv6 key layer when
we match tcp flags and the IPv6 key layer has not been included
already.

Fixes: 07e1671c ("nfp: flower: refactor shared ip header in match offload")
Signed-off-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ibmvnic_reset allocated new reset work item objects in a non-atomic
context. This can be called from a tasklet, generating the output below.
Allocate work items with the GFP_ATOMIC flag instead.

BUG: sleeping function called from invalid context at mm/slab.h:421
in_atomic(): 1, irqs_disabled(): 1, pid: 93, name: kworker/0:2
INFO: lockdep is turned off.
irq event stamp: 66049
hardirqs last  enabled at (66048): [<c000000000122468>] tasklet_action_common.isra.12+0x78/0x1c0
hardirqs last disabled at (66049): [<c000000000befce8>] _raw_spin_lock_irqsave+0x48/0xf0
softirqs last  enabled at (66044): [<c000000000a8ac78>] dev_deactivate_queue.constprop.28+0xc8/0x160
softirqs last disabled at (66045): [<c0000000000306e0>] call_do_softirq+0x14/0x24
CPU: 0 PID: 93 Comm: kworker/0:2 Kdump: loaded Not tainted 4.20.0-rc6-00001-g1b50a8f03706 #7
Workqueue: events linkwatch_event
Call Trace:
[c0000003fffe7ae0] [c000000000bc83e4] dump_stack+0xe8/0x164 (unreliable)
[c0000003fffe7b30] [c00000000015ba0c] ___might_sleep+0x2dc/0x320
[c0000003fffe7bb0] [c000000000391514] kmem_cache_alloc_trace+0x3e4/0x440
[c0000003fffe7c30] [d000000005b2309c] ibmvnic_reset+0x16c/0x360 [ibmvnic]
[c0000003fffe7cc0] [d000000005b29834] ibmvnic_tasklet+0x1054/0x2010 [ibmvnic]
[c0000003fffe7e00] [c0000000001224c8] tasklet_action_common.isra.12+0xd8/0x1c0
[c0000003fffe7e60] [c000000000bf1238] __do_softirq+0x1a8/0x64c
[c0000003fffe7f90] [c0000000000306e0] call_do_softirq+0x14/0x24
[c0000003f3967980] [c00000000001ba50] do_softirq_own_stack+0x60/0xb0
[c0000003f39679c0] [c0000000001218a8] do_softirq+0xa8/0x100
[c0000003f39679f0] [c000000000121a74] __local_bh_enable_ip+0x174/0x180
[c0000003f3967a60] [c000000000bf003c] _raw_spin_unlock_bh+0x5c/0x80
[c0000003f3967a90] [c000000000a8ac78] dev_deactivate_queue.constprop.28+0xc8/0x160
[c0000003f3967ad0] [c000000000a8c8b0] dev_deactivate_many+0xd0/0x520
[c0000003f3967b70] [c000000000a8cd40] dev_deactivate+0x40/0x60
[c0000003f3967ba0] [c000000000a5e0c4] linkwatch_do_dev+0x74/0xd0
[c0000003f3967bd0] [c000000000a5e694] __linkwatch_run_queue+0x1a4/0x1f0
[c0000003f3967c30] [c000000000a5e728] linkwatch_event+0x48/0x60
[c0000003f3967c50] [c0000000001444e8] process_one_work+0x238/0x710
[c0000003f3967d20] [c000000000144a48] worker_thread+0x88/0x4e0
[c0000003f3967db0] [c00000000014e3a8] kthread+0x178/0x1c0
[c0000003f3967e20] [c00000000000bfd0] ret_from_kernel_thread+0x5c/0x6c
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ibmvnic_reset can create and schedule a reset work item from
an IRQ context, so do not use a mutex, which can sleep. Convert
the reset work item mutex to a spin lock. Locking debugger generated
the trace output below.

BUG: sleeping function called from invalid context at kernel/locking/mutex.c:908
in_atomic(): 1, irqs_disabled(): 1, pid: 120, name: kworker/8:1
4 locks held by kworker/8:1/120:
 #0: 0000000017c05720 ((wq_completion)"events"){+.+.}, at: process_one_work+0x188/0x710
 #1: 00000000ace90706 ((linkwatch_work).work){+.+.}, at: process_one_work+0x188/0x710
 #2: 000000007632871f (rtnl_mutex){+.+.}, at: rtnl_lock+0x30/0x50
 #3: 00000000fc36813a (&(&crq->lock)->rlock){..-.}, at: ibmvnic_tasklet+0x88/0x2010 [ibmvnic]
irq event stamp: 26293
hardirqs last  enabled at (26292): [<c000000000122468>] tasklet_action_common.isra.12+0x78/0x1c0
hardirqs last disabled at (26293): [<c000000000befce8>] _raw_spin_lock_irqsave+0x48/0xf0
softirqs last  enabled at (26288): [<c000000000a8ac78>] dev_deactivate_queue.constprop.28+0xc8/0x160
softirqs last disabled at (26289): [<c0000000000306e0>] call_do_softirq+0x14/0x24
CPU: 8 PID: 120 Comm: kworker/8:1 Kdump: loaded Not tainted 4.20.0-rc6 #6
Workqueue: events linkwatch_event
Call Trace:
[c0000003fffa7a50] [c000000000bc83e4] dump_stack+0xe8/0x164 (unreliable)
[c0000003fffa7aa0] [c00000000015ba0c] ___might_sleep+0x2dc/0x320
[c0000003fffa7b20] [c000000000be960c] __mutex_lock+0x8c/0xb40
[c0000003fffa7c30] [d000000006202ac8] ibmvnic_reset+0x78/0x330 [ibmvnic]
[c0000003fffa7cc0] [d0000000062097f4] ibmvnic_tasklet+0x1054/0x2010 [ibmvnic]
[c0000003fffa7e00] [c0000000001224c8] tasklet_action_common.isra.12+0xd8/0x1c0
[c0000003fffa7e60] [c000000000bf1238] __do_softirq+0x1a8/0x64c
[c0000003fffa7f90] [c0000000000306e0] call_do_softirq+0x14/0x24
[c0000003f3f87980] [c00000000001ba50] do_softirq_own_stack+0x60/0xb0
[c0000003f3f879c0] [c0000000001218a8] do_softirq+0xa8/0x100
[c0000003f3f879f0] [c000000000121a74] __local_bh_enable_ip+0x174/0x180
[c0000003f3f87a60] [c000000000bf003c] _raw_spin_unlock_bh+0x5c/0x80
[c0000003f3f87a90] [c000000000a8ac78] dev_deactivate_queue.constprop.28+0xc8/0x160
[c0000003f3f87ad0] [c000000000a8c8b0] dev_deactivate_many+0xd0/0x520
[c0000003f3f87b70] [c000000000a8cd40] dev_deactivate+0x40/0x60
[c0000003f3f87ba0] [c000000000a5e0c4] linkwatch_do_dev+0x74/0xd0
[c0000003f3f87bd0] [c000000000a5e694] __linkwatch_run_queue+0x1a4/0x1f0
[c0000003f3f87c30] [c000000000a5e728] linkwatch_event+0x48/0x60
[c0000003f3f87c50] [c0000000001444e8] process_one_work+0x238/0x710
[c0000003f3f87d20] [c000000000144a48] worker_thread+0x88/0x4e0
[c0000003f3f87db0] [c00000000014e3a8] kthread+0x178/0x1c0
[c0000003f3f87e20] [c00000000000bfd0] ret_from_kernel_thread+0x5c/0x6c
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CP rings are accounted differently on the new 57500 chips.  There
must be enough CP rings for the sum of RX and TX rings on the new
chips.  The current logic may be over-estimating the RX and TX rings.

The output parameter max_cp should be the maximum NQs capped by
MSIX vectors available for networking in the context of 57500 chips.
The existing code which uses CMPL rings capped by the MSIX vectors
works most of the time but is not always correct.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new 57500 chips have introduced the NQ structure in addition to
the existing CP rings in all chips.  We need to introduce a new
bnxt_nq_rings_in_use().  On legacy chips, the 2 functions are the
same and one will just call the other.  On the new chips, they
refer to the 2 separate ring structures.  The new function is now
called to determine the resource (NQ or CP rings) associated with
MSIX that are in use.

On 57500 chips, the RDMA driver does not use the CP rings so
we don't need to do the subtraction adjustment.

Fixes: 41e8d798 ("bnxt_en: Modify the ring reservation functions for 57500 series chips.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The new 57500 chips use 1 NQ per MSIX vector, whereas legacy chips use
1 CP ring per MSIX vector.  To better unify this, add a resv_irqs
field to struct bnxt_hw_resc.  On legacy chips, we initialize resv_irqs
with resv_cp_rings.  On new chips, we initialize it with the allocated
MSIX resources.
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Recent changes to support the 57500 devices have created this
regression.  The bnxt_hwrm_queue_qportcfg() call was moved to be
called earlier before the RDMA support was determined, causing
the CoS queues configuration to be set before knowing whether RDMA
was supported or not.  Fix it by moving it to the right place right
after RDMA support is determined.

Fixes: 98f04cf0 ("bnxt_en: Check context memory requirements from firmware.")
Signed-off-by: NMichael Chan <michael.chan@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

rx_ppp and tx_ppp can be set between 0 and 255, so don't clamp to 1.

Fixes: 6e8814ce ("net/mlx4_en: Fix mixed PFC and Global pause user control requests")
Signed-off-by: NTarick Bedeir <tarick@google.com>
Reviewed-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts commit 624ca9c3.

This commit is completely bogus. The STACR register has two formats, old
and new, depending on the version of the IP block used. There's a pair of
device-tree properties that can be used to specify the format used:

	has-inverted-stacr-oc
	has-new-stacr-staopc

What this commit did was to change the bit definition used with the old
parts to match the new parts. This of course breaks the driver on all
the old ones.

Instead, the author should have set the appropriate properties in the
device-tree for the variant used on his board.
Signed-off-by: NBenjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When deleting a VLAN device using an ioctl the netdev is unregistered
before the VLAN filter is updated via ndo_vlan_rx_kill_vid(). It can
lead to a use-after-free in mlxsw in case the VLAN device is deleted
while being enslaved to a bridge.

The reason for the above is that when mlxsw receives the CHANGEUPPER
event, it wrongly assumes that the VLAN device is no longer its upper
and thus destroys the internal representation of the bridge port despite
the reference count being non-zero.

Fix this by checking if the VLAN device is our upper using its real
device. In net-next I'm going to remove this trick and instead make
mlxsw completely agnostic to the order of the events.

Fixes: c57529e1 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

GRE decap offload is configured when local routes prefix correspond to the
local address of one of the offloaded GRE tunnels. The matching check was
found to be too strict, such that for a flat GRE configuration, in which
the overlay and underlay traffic share the same non-default VRF, decap flow
was not offloaded.

Relax the check for decap flow offloading. A match occurs if the local
address of the tunnel matches the local route address while both share the
same VRF table.

Fixes: 4607f6d2 ("mlxsw: spectrum_router: Support IPv4 underlay decap")
Signed-off-by: NNir Dotan <nird@mellanox.com>
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It should never be possible for a user to set a VNI on a FID in case one
is already set. The driver therefore returns an error, but fails to drop
the reference count taken earlier when calling
mlxsw_sp_fid_8021d_lookup().

Drop the reference when this unlikely error is hit.

Fixes: 1c30d183 ("mlxsw: spectrum: Enable VxLAN enslavement to bridges")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NJiri Pirko <jiri@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

It is possible to trigger a warning in mlxsw in case a flood entry which
mlxsw is not aware of is deleted from the VxLAN device. This is because
mlxsw expects to find a singly linked list where the flood entry is
present in.

Fix by removing these warnings for now.

Will re-add them in the next release after we teach mlxsw to ask for a
dump of FDB entries from the VxLAN device, once it is enslaved to a
bridge mlxsw cares about.

Fixes: 6e6030bd ("mlxsw: spectrum_nve: Implement common NVE core")
Signed-off-by: NIdo Schimmel <idosch@mellanox.com>
Reviewed-by: NPetr Machata <petrm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The .validate phylink callback should empty the supported bitmap when
the interface mode is invalid.

Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Reported-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The mvpp2_phylink_validate() relies on the interface field of
phylink_link_state to determine valid link modes. However, when called
from phylink_sfp_module_insert() this field in not initialized. The
default switch case then excludes 10G link modes. This allows 10G SFP
modules that are detected correctly to be configured at max rate of
2.5G.

Catch the uninitialized PHY mode case, and allow 10G rates.

Fixes: d97c9f4a ("net: mvpp2: 1000baseX support")
Cc: Maxime Chevallier <maxime.chevallier@bootlin.com>
Cc: Antoine Tenart <antoine.tenart@bootlin.com>
Acked-by: NRussell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: NBaruch Siach <baruch@tkos.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

After getting a reference to the platform device's of_node the probe
function ends up calling of_find_matching_node() using the node as an
argument. The function takes care of decreasing the refcount on it. We
are then incorrectly decreasing the refcount on that node again.

This patch removes the unwarranted call to of_node_put().

Fixes: 414fd46e ("fsl/fman: Add FMan support")
Signed-off-by: NNicolas Saenz Julienne <nsaenzjulienne@suse.de>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This reverts:

ef1b5bf5 ("net: phy: Fix not to call phy_resume() if PHY is not attached")
8c85f4b8 ("net: phy: micrel: add toggling phy reset if PHY is not  attached")

Andrew Lunn informs me that there are alternative efforts
underway to fix this more properly.
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MLX4_EN depends on NETDEVICES, ETHERNET and INET Kconfigs.
Make sure they are listed in MLX4_EN Kconfig dependencies.

This fixes the following build break:

drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: ‘struct iphdr’ declared inside parameter list [enabled by default]
struct iphdr *iph)
^
drivers/net/ethernet/mellanox/mlx4/en_rx.c:582:18: warning: its scope is only this definition or declaration, which is probably not what you want [enabled by default]
drivers/net/ethernet/mellanox/mlx4/en_rx.c: In function ‘get_fixed_ipv4_csum’:
drivers/net/ethernet/mellanox/mlx4/en_rx.c:586:20: error: dereferencing pointer to incomplete type
_u8 ipproto = iph->protocol;
Signed-off-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

NIC driver minimal MTU size shall be set to ETH_MIN_MTU, as defined in
the RFC791 and in the network stack. Remove old mlx4_en only define for
it, which was set to wrong value.

Fixes: b80f71f5 ("ethernet/mellanox: use core min/max MTU checking")
Signed-off-by: NEran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: NTariq Toukan <tariqt@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Disable hardware level MAC learning because it breaks station roaming.
When enabled it drops all frames that arrive from a MAC address
that is on a different port at learning table.
Signed-off-by: NAnderson Luiz Alves <alacn1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A MAC address must be unique among all the macvlan devices with the same
lower device. The only exception is the passthru [sic] mode,
which shares the lower device address.

When duplicate addresses are detected, EBUSY is returned when bringing
the interface up:

    # ip link add macvlan0 link eth0 type macvlan
    # read addr </sys/class/net/eth0/address
    # ip link set macvlan0 address $addr
    # ip link set macvlan0 up
    RTNETLINK answers: Device or resource busy

Use correct error code which is EADDRINUSE, and do the check also
earlier, on address change:

    # ip link set macvlan0 address $addr
    RTNETLINK answers: Address already in use
Signed-off-by: NMatteo Croce <mcroce@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Commit a5681e20 ("net/ibmnvic: Fix deadlock problem
in reset") made the change to hold the RTNL lock during
driver reset but still calls netdev_notify_peers, which
results in a deadlock. Instead, use call_netdevice_notifiers,
which is functionally the same except that it does not
take the RTNL lock again.

Fixes: a5681e20 ("net/ibmnvic: Fix deadlock problem in reset")
Signed-off-by: NThomas Falcon <tlfalcon@linux.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds toggling phy reset if PHY is not attached. Otherwise,
some boards (e.g. R-Car H3 Salvator-XS) cannot link up correctly if
we do the following method:

 1) Kernel boots by using initramfs.
 --> No open the nic, so phy_device_register() and phy_probe()
     deasserts the reset.
 2) Kernel enters the suspend.
 --> So, keep the reset signal as deassert.
 --> On R-Car Salvator-XS board, unfortunately, the board power is
     turned off.
 3) Kernel returns from suspend.
 4) ifconfig eth0 up
 --> Then, since edge signal of the reset doesn't happen,
     it cannot link up.
 5) ifconfig eth0 down
 6) ifconfig eth0 up
 --> In this case, it can link up.
Reported-by: NHiromitsu Yamasaki <hiromitsu.yamasaki.ym@renesas.com>
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes an issue that mdio_bus_phy_resume() doesn't call
phy_resume() if the PHY is not attached.

Fixes: 803dd9c7 ("net: phy: avoid suspending twice a PHY")
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In tun.c skb->len was accessed while doing stats accounting after a
call to netif_receive_skb. We can not access skb after this call
because buffers may be dropped.

The fix for this bug would be to store skb->len in local variable and
then use it after netif_receive_skb(). IMO using xdp data size for
accounting bytes will be better because input for tun_xdp_one() is
xdp_buff.

Hence this patch:
- fixes a bug by removing skb access after netif_receive_skb()
- uses xdp data size for accounting bytes

[613.019057] BUG: KASAN: use-after-free in tun_sendmsg+0x77c/0xc50 [tun]
[613.021062] Read of size 4 at addr ffff8881da9ab7c0 by task vhost-1115/1155
[613.023073]
[613.024003] CPU: 0 PID: 1155 Comm: vhost-1115 Not tainted 4.20.0-rc3-vm+ #232
[613.026029] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014
[613.029116] Call Trace:
[613.031145]  dump_stack+0x5b/0x90
[613.032219]  print_address_description+0x6c/0x23c
[613.034156]  ? tun_sendmsg+0x77c/0xc50 [tun]
[613.036141]  kasan_report.cold.5+0x241/0x308
[613.038125]  tun_sendmsg+0x77c/0xc50 [tun]
[613.040109]  ? tun_get_user+0x1960/0x1960 [tun]
[613.042094]  ? __isolate_free_page+0x270/0x270
[613.045173]  vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.047127]  ? peek_head_len.part.13+0x90/0x90 [vhost_net]
[613.049096]  ? get_tx_bufs+0x5a/0x2c0 [vhost_net]
[613.051106]  ? vhost_enable_notify+0x2d8/0x420 [vhost]
[613.053139]  handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.053139]  ? vhost_net_buf_peek+0x340/0x340 [vhost_net]
[613.053139]  ? __mutex_lock+0x8d9/0xb30
[613.053139]  ? finish_task_switch+0x8f/0x3f0
[613.053139]  ? handle_tx+0x32/0x120 [vhost_net]
[613.053139]  ? mutex_trylock+0x110/0x110
[613.053139]  ? finish_task_switch+0xcf/0x3f0
[613.053139]  ? finish_task_switch+0x240/0x3f0
[613.053139]  ? __switch_to_asm+0x34/0x70
[613.053139]  ? __switch_to_asm+0x40/0x70
[613.053139]  ? __schedule+0x506/0xf10
[613.053139]  handle_tx+0xc7/0x120 [vhost_net]
[613.053139]  vhost_worker+0x166/0x200 [vhost]
[613.053139]  ? vhost_dev_init+0x580/0x580 [vhost]
[613.053139]  ? __kthread_parkme+0x77/0x90
[613.053139]  ? vhost_dev_init+0x580/0x580 [vhost]
[613.053139]  kthread+0x1b1/0x1d0
[613.053139]  ? kthread_park+0xb0/0xb0
[613.053139]  ret_from_fork+0x35/0x40
[613.088705]
[613.088705] Allocated by task 1155:
[613.088705]  kasan_kmalloc+0xbf/0xe0
[613.088705]  kmem_cache_alloc+0xdc/0x220
[613.088705]  __build_skb+0x2a/0x160
[613.088705]  build_skb+0x14/0xc0
[613.088705]  tun_sendmsg+0x4f0/0xc50 [tun]
[613.088705]  vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.088705]  handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.088705]  handle_tx+0xc7/0x120 [vhost_net]
[613.088705]  vhost_worker+0x166/0x200 [vhost]
[613.088705]  kthread+0x1b1/0x1d0
[613.088705]  ret_from_fork+0x35/0x40
[613.088705]
[613.088705] Freed by task 1155:
[613.088705]  __kasan_slab_free+0x12e/0x180
[613.088705]  kmem_cache_free+0xa0/0x230
[613.088705]  ip6_mc_input+0x40f/0x5a0
[613.088705]  ipv6_rcv+0xc9/0x1e0
[613.088705]  __netif_receive_skb_one_core+0xc1/0x100
[613.088705]  netif_receive_skb_internal+0xc4/0x270
[613.088705]  br_pass_frame_up+0x2b9/0x2e0
[613.088705]  br_handle_frame_finish+0x2fb/0x7a0
[613.088705]  br_handle_frame+0x30f/0x6c0
[613.088705]  __netif_receive_skb_core+0x61a/0x15b0
[613.088705]  __netif_receive_skb_one_core+0x8e/0x100
[613.088705]  netif_receive_skb_internal+0xc4/0x270
[613.088705]  tun_sendmsg+0x738/0xc50 [tun]
[613.088705]  vhost_tx_batch.isra.14+0xeb/0x1f0 [vhost_net]
[613.088705]  handle_tx_copy+0x2d0/0x8f0 [vhost_net]
[613.088705]  handle_tx+0xc7/0x120 [vhost_net]
[613.088705]  vhost_worker+0x166/0x200 [vhost]
[613.088705]  kthread+0x1b1/0x1d0
[613.088705]  ret_from_fork+0x35/0x40
[613.088705]
[613.088705] The buggy address belongs to the object at ffff8881da9ab740
[613.088705]  which belongs to the cache skbuff_head_cache of size 232

Fixes: 043d222f ("tuntap: accept an array of XDP buffs through sendmsg()")
Reviewed-by: NToshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: NPrashant Bhole <bhole_prashant_q7@lab.ntt.co.jp>
Acked-by: NJason Wang <jasowang@redhat.com>
Acked-by: NMichael S. Tsirkin <mst@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing mtu many times with traffic, a bug is triggered:

[ 1035.684037] kernel BUG at lib/dynamic_queue_limits.c:26!
[ 1035.684042] invalid opcode: 0000 [#1] SMP
[ 1035.684049] Modules linked in: loop binfmt_misc 8139cp(OE) macsec
tcp_diag udp_diag inet_diag unix_diag af_packet_diag netlink_diag tcp_lp
fuse uinput xt_CHECKSUM iptable_mangle ipt_MASQUERADE
nf_nat_masquerade_ipv4 iptable_nat nf_nat_ipv4 nf_nat nf_conntrack_ipv4
nf_defrag_ipv4 xt_conntrack nf_conntrack ipt_REJECT nf_reject_ipv4 tun
bridge stp llc ebtable_filter ebtables ip6table_filter devlink
ip6_tables iptable_filter sunrpc snd_hda_codec_generic snd_hda_intel
snd_hda_codec snd_hda_core snd_hwdep ppdev snd_seq iosf_mbi crc32_pclmul
parport_pc snd_seq_device ghash_clmulni_intel parport snd_pcm
aesni_intel joydev lrw snd_timer virtio_balloon sg gf128mul glue_helper
ablk_helper cryptd snd soundcore i2c_piix4 pcspkr ip_tables xfs
libcrc32c sr_mod sd_mod cdrom crc_t10dif crct10dif_generic ata_generic
[ 1035.684102]  pata_acpi virtio_console qxl drm_kms_helper syscopyarea
sysfillrect sysimgblt floppy fb_sys_fops crct10dif_pclmul
crct10dif_common ttm crc32c_intel serio_raw ata_piix drm libata 8139too
virtio_pci drm_panel_orientation_quirks virtio_ring virtio mii dm_mirror
dm_region_hash dm_log dm_mod [last unloaded: 8139cp]
[ 1035.684132] CPU: 9 PID: 25140 Comm: if-mtu-change Kdump: loaded
Tainted: G           OE  ------------ T 3.10.0-957.el7.x86_64 #1
[ 1035.684134] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 1035.684136] task: ffff8f59b1f5a080 ti: ffff8f5a2e32c000 task.ti:
ffff8f5a2e32c000
[ 1035.684149] RIP: 0010:[<ffffffffba3a40d0>]  [<ffffffffba3a40d0>]
dql_completed+0x180/0x190
[ 1035.684162] RSP: 0000:ffff8f5a75483e50  EFLAGS: 00010093
[ 1035.684162] RAX: 00000000000000c2 RBX: ffff8f5a6f91c000 RCX:
0000000000000000
[ 1035.684162] RDX: 0000000000000000 RSI: 0000000000000184 RDI:
ffff8f599fea3ec0
[ 1035.684162] RBP: ffff8f5a75483ea8 R08: 00000000000000c2 R09:
0000000000000000
[ 1035.684162] R10: 00000000000616ef R11: ffff8f5a75483b56 R12:
ffff8f599fea3e00
[ 1035.684162] R13: 0000000000000001 R14: 0000000000000000 R15:
0000000000000184
[ 1035.684162] FS:  00007fa8434de740(0000) GS:ffff8f5a75480000(0000)
knlGS:0000000000000000
[ 1035.684162] CS:  0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1035.684162] CR2: 00000000004305d0 CR3: 000000024eb66000 CR4:
00000000001406e0
[ 1035.684162] Call Trace:
[ 1035.684162]  <IRQ>
[ 1035.684162]  [<ffffffffc08cbaf8>] ? cp_interrupt+0x478/0x580 [8139cp]
[ 1035.684162]  [<ffffffffba14a294>]
__handle_irq_event_percpu+0x44/0x1c0
[ 1035.684162]  [<ffffffffba14a442>] handle_irq_event_percpu+0x32/0x80
[ 1035.684162]  [<ffffffffba14a4cc>] handle_irq_event+0x3c/0x60
[ 1035.684162]  [<ffffffffba14db29>] handle_fasteoi_irq+0x59/0x110
[ 1035.684162]  [<ffffffffba02e554>] handle_irq+0xe4/0x1a0
[ 1035.684162]  [<ffffffffba7795dd>] do_IRQ+0x4d/0xf0
[ 1035.684162]  [<ffffffffba76b362>] common_interrupt+0x162/0x162
[ 1035.684162]  <EOI>
[ 1035.684162]  [<ffffffffba0c2ae4>] ? __wake_up_bit+0x24/0x70
[ 1035.684162]  [<ffffffffba1e46f5>] ? do_set_pte+0xd5/0x120
[ 1035.684162]  [<ffffffffba1b64fb>] unlock_page+0x2b/0x30
[ 1035.684162]  [<ffffffffba1e4879>] do_read_fault.isra.61+0x139/0x1b0
[ 1035.684162]  [<ffffffffba1e9134>] handle_pte_fault+0x2f4/0xd10
[ 1035.684162]  [<ffffffffba1ebc6d>] handle_mm_fault+0x39d/0x9b0
[ 1035.684162]  [<ffffffffba76f5e3>] __do_page_fault+0x203/0x500
[ 1035.684162]  [<ffffffffba76f9c6>] trace_do_page_fault+0x56/0x150
[ 1035.684162]  [<ffffffffba76ef42>] do_async_page_fault+0x22/0xf0
[ 1035.684162]  [<ffffffffba76b788>] async_page_fault+0x28/0x30
[ 1035.684162] Code: 54 c7 47 54 ff ff ff ff 44 0f 49 ce 48 8b 35 48 2f
9c 00 48 89 77 58 e9 fe fe ff ff 0f 1f 80 00 00 00 00 41 89 d1 e9 ef fe
ff ff <0f> 0b 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 40 00 55 8d 42 ff 48
[ 1035.684162] RIP  [<ffffffffba3a40d0>] dql_completed+0x180/0x190
[ 1035.684162]  RSP <ffff8f5a75483e50>

It's not the same as in 7fe0ee09 patch described.
As 8139cp uses shared irq mode, other device irq will trigger
cp_interrupt to execute.

cp_change_mtu
 -> cp_close
 -> cp_open

In cp_close routine  just before free_irq(), some interrupt may occur.
In my environment, cp_interrupt exectutes and IntrStatus is 0x4,
exactly TxOk. That will cause cp_tx to wake device queue.

As device queue is started, cp_start_xmit and cp_open will run at same
time which will cause kernel BUG.

For example:
[#] for tx descriptor

At start:

[#][#][#]
num_queued=3

After cp_init_hw->cp_start_hw->netdev_reset_queue:

[#][#][#]
num_queued=0

When 8139cp starts to work then cp_tx will check
num_queued mismatchs the complete_bytes.

The patch will check IntrMask before check IntrStatus in cp_interrupt.
When 8139cp interrupt is disabled, just return.
Signed-off-by: NSu Yanjun <suyj.fnst@cn.fujitsu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently __set_phy_supported allows to add modes w/o checking whether
the PHY supports them. This is wrong, it should never add modes but
only remove modes we don't want to support.

The commit marked as fixed didn't do anything wrong, it just copied
existing functionality to the helper which is being fixed now.

Fixes: f3a6bd39 ("phylib: Add phy_set_max_speed helper")
Signed-off-by: NHeiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes a off-by-one mistake in nla_parse_nested() functions of
mac802154_hwsim driver. I had to enabled stack protector so I was able
to reproduce it.

Reference: https://github.com/linux-wpan/wpan-tools/issues/17Signed-off-by: NAlexander Aring <aring@mojatatu.com>
Signed-off-by: NStefan Schmidt <stefan@datenfreihafen.org>

It's not supported right now (the goal of the initial patch was to support
'ip link del' only).

Before the patch:
$ ip link add foo type tun
[  239.632660] BUG: unable to handle kernel NULL pointer dereference at 0000000000000000
[snip]
[  239.636410] RIP: 0010:register_netdevice+0x8e/0x3a0

This panic occurs because dev->netdev_ops is not set by tun_setup(). But to
have something usable, it will require more than just setting
netdev_ops.

Fixes: f019a7a5 ("tun: Implement ip link del tunXXX")
CC: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: NNicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We copy vnet header unconditionally in page_to_skb() this is wrong
since XDP may modify the packet data. So let's keep a zeroed vnet
header for not confusing the conversion between vnet header and skb
metadata.

In the future, we should able to detect whether or not the packet was
modified and keep using the vnet header when packet was not touched.

Fixes: f600b690 ("virtio_net: Add XDP support")
Reported-by: NPavel Popa <pashinho1990@gmail.com>
Signed-off-by: NJason Wang <jasowang@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The function lio_vf_rep_packet_sent_callback releases the occupation of
sc via octeon_free_soft_command. sc should not be used after that.
Unfortunately, sc->iq_no is read. To fix this, the patch stores sc->iq_no
into a local variable before releasing sc and then uses the local variable
instead of sc->iq_no.
Signed-off-by: NPan Bian <bianpan2016@163.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IP header is not necessarily located right after struct ethhdr,
there could be multiple 802.1Q headers in between, this is why
we call __vlan_get_protocol().

Fixes: fe1dc069 ("net/mlx5e: don't set CHECKSUM_COMPLETE on SCTP packets")
Cc: Alaa Hleihel <alaa@mellanox.com>
Cc: Or Gerlitz <ogerlitz@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NCong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: NTariq Toukan <tariqt@mellanox.com>
Acked-by: NSaeed Mahameed <saeedm@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For flow offload adds, if the rhash insert code fails, the flow will still
have been offloaded but the reference to it in the driver freed.

Re-order the offload setup calls to ensure that a flow will only be written
to FW if a kernel reference is held and stored in the rhashtable. Remove
this hashtable entry if the offload fails.

Fixes: c01d0efa ("nfp: flower: use rhashtable for flow caching")
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Calling nfp_compile_flow_metadata both assigns a stats context and
increments a ref counter on (or allocates) a mask id table entry. These
are released by the nfp_modify_flow_metadata call on flow deletion,
however, if a flow add fails after metadata is set then the flow entry
will be deleted but the metadata assignments leaked.

Add an error path to the flow add offload function to ensure allocated
metadata is released in the event of an offload fail.

Fixes: 81f3ddf2 ("nfp: add control message passing capabilities to flower offloads")
Signed-off-by: NJohn Hurley <john.hurley@netronome.com>
Reviewed-by: NPieter Jansen van Vuuren <pieter.jansenvanvuuren@netronome.com>
Reviewed-by: NJakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>