Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 13 11月, 2015 3 次提交
  3. 10 11月, 2015 1 次提交
    • R
      ath10k: fix invalid NSS for 4x4 devices · f680f70a
      由 Rajkumar Manoharan 提交于 
      The number of spatial streams that are derived from chain mask
for 4x4 devices is using wrong bitmask and conditional check.
This is affecting downlink throughput for QCA99x0 devices. Earlier
cfg_tx_chainmask is not filled by default until user configured it
and so get_nss_from_chainmask never be called. This issue is exposed
by recent commit 166de3f1 ("ath10k: remove supported chain mask").
By default maximum supported chain mask is filled in cfg_tx_chainmask.

Cc: stable@vger.kernel.org
Fixes: 5572a95b ("ath10k: apply chainmask settings to vdev on creation")
Signed-off-by: NRajkumar Manoharan <rmanohar@qti.qualcomm.com>
Signed-off-by: NKalle Valo <kvalo@qca.qualcomm.com>
      f680f70a
  5. 09 11月, 2015 1 次提交
  7. 08 11月, 2015 4 次提交
    • M
      dwc_eth_qos: Delete an unnecessary check before the function call "of_node_put" · 3694bfbd
      由 Markus Elfring 提交于 
      The of_node_put() function tests whether its argument is NULL
and then returns immediately.
Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      3694bfbd
    • J
      bonding: fix panic on non-ARPHRD_ETHER enslave failure · 40baec22
      由 Jay Vosburgh 提交于 
      Since commit 7d5cd2ce529b, when bond_enslave fails on devices that
are not ARPHRD_ETHER, if needed, it resets the bonding device back to
ARPHRD_ETHER by calling ether_setup.

	Unfortunately, ether_setup clobbers dev->flags, clearing IFF_UP
if the bond device is up, leaving it in a quasi-down state without
having actually gone through dev_close.  For bonding, if any periodic
work queue items are active (miimon, arp_interval, etc), those will
remain running, as they are stopped by bond_close.  At this point, if
the bonding module is unloaded or the bond is deleted, the system will
panic when the work function is called.

	This panic is resolved by calling dev_close on the bond itself
prior to calling ether_setup.

Cc: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NJay Vosburgh <jay.vosburgh@canonical.com>
Fixes: 7d5cd2ce ("bonding: correctly handle bonding type change on enslave failure")
Acked-by: NNikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      40baec22
    • J
      net/qlcnic: fix mac address restore in bond mode 5/6 · e824de8a
      由 Jarod Wilson 提交于 
      The bonding driver saves a copy of slaves' original mac address and then
assigns whatever mac as needed to the slave, depending on mode. In at
least modes 5 and 6 (balance-tlb, balance-alb), it often ends up being the
mac address of another slave. On release from the bond, the original mac
address is supposed to get restored via a dev_set_mac_address() call in
the bonding driver's __bond_release_one() function, which calls the
slave's ndo_set_mac_address function, which for qlcnic, is
qlcnic_set_mac().

Now, this function tries to be somewhat intelligent and exit early if
you're trying to set the mac address to the same thing that is already
set. The problem here is that adapter->mac_addr isn't in sync with
netdev->dev_addr. The qlcnic driver still has the original mac stored in
adapter->mac_addr, while the bonding driver has updated netdev->dev_addr,
so qlcnic thinks we're trying to set the same address it already has.

I think the way to go here, since the function updates both netdev and
adapter's stored mac addresses, is to check if either of them doesn't
match the newly requested mac. Simply checking netdev's value only could
result in a similar mismatch and non-update, so look at both.

CC: Dept-GELinuxNICDev@qlogic.com
CC: netdev@vger.kernel.org
CC: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: NJarod Wilson <jarod@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      e824de8a
    • M
      fjes: Delete an unnecessary check before the function call "vfree" · f7b5964d
      由 Markus Elfring 提交于 
      The vfree() function performs also input parameter validation.
Thus the test around the call is not needed.

This issue was detected by using the Coccinelle software.
Signed-off-by: NMarkus Elfring <elfring@users.sourceforge.net>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      f7b5964d
  9. 06 11月, 2015 9 次提交
  11. 05 11月, 2015 13 次提交
  13. 04 11月, 2015 9 次提交