unused
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

not used anymore
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Tested by modifying iproute2 to allow sending a divisor > 255
Tested-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Operation makes no sense.  Nothing will actually break if we do so
(depth limit in u32_classify() will prevent infinite loops), but
according to maintainers it's best prohibited outright.

NOTE: doing so guarantees that u32_destroy() will trigger the call
of u32_destroy_hnode(); we might want to make that unconditional.

Test:
tc qdisc add dev eth0 ingress
tc filter add dev eth0 parent ffff: protocol ip prio 100 u32 \
link 800: offset at 0 mask 0f00 shift 6 plus 0 eat match ip protocol 6 ff
should fail with
Error: cls_u32: Not linking to root node
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

... and produce consistent error on attempt to delete such.
Existing check in u32_delete() is inconsistent - after

tc qdisc add dev eth0 ingress
tc filter add dev eth0 parent ffff: protocol ip prio 100 handle 1: u32 \
divisor 1
tc filter add dev eth0 parent ffff: protocol ip prio 200 handle 2: u32 \
divisor 1

both

tc filter delete dev eth0 parent ffff: protocol ip prio 100 handle 801: u32

and

tc filter delete dev eth0 parent ffff: protocol ip prio 100 handle 800: u32

will fail (at least with refcounting fixes), but the former will complain
about an attempt to remove a busy table, while the latter will recognize
it as root and yield "Not allowed to delete root node" instead.

The problem with the existing check is that several tcf_proto instances
might share the same tp->data and handle-to-hnode lookup will be the same
for all of them. So comparing an hnode to be deleted with tp->root won't
catch the case when one tp is used to try deleting the root of another.
Solution is trivial - mark the root hnodes explicitly upon allocation and
check for that.
Signed-off-by: NAl Viro <viro@zeniv.linux.org.uk>
Signed-off-by: NJamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quentin Schulz says:

====================
net: phy: mscc: add support for VSC8584 and VSC8574 Microsemi quad-port PHYs

RESEND: rebased on top of latest net-next and on top of latest version of
"net: phy: mscc: various improvements to Microsemi PHY driver" patch
series.

Both PHYs are 4-port PHY that are 10/100/1000BASE-T, 100BASE-FX, 1000BASE-X
and triple-speed copper SFP capable, can communicate with the MAC via
SGMII, QSGMII or 1000BASE-X, supports downshifting and can set the blinking
pattern of each of its 4 LEDs, supports SyncE as well as HP Auto-MDIX
detection.

VSC8574 supports WOL and VSC8584 supports hardware offloading of MACsec.

This patch series add support for 10/100/1000BASE-T, SGMII/QSGMII link with
the MAC, downshifting, HP Auto-MDIX detection and blinking pattern for
their 4 LEDs.

They have also an internal Intel 8051 microcontroller whose firmware needs
to be patched when the PHY is reset. If the 8051's firmware has the
expected CRC, its patching can be skipped. The microcontroller can be
accessed from any port of the PHY, though the CRC function can only be done
through the PHY that is the base PHY of the package (internal address 0)
due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs in
the package. So any modification in any register of this bank affects all
PHYs of the package.

If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is required
to clear the interrupts mask register of all PHYs before being able to use
interrupts with any PHY. The first PHY of the package that will be init
will take care of clearing all PHYs interrupts mask registers. Thus, we
need to keep track of the init sequence in the package, if it's already
been done or if it's to be done.

Most of the init sequence of a PHY of the package is common to all PHYs in
the package, thus we use the SMI broadcast feature which enables us to
propagate a write in one register of one PHY to all PHYs in the same
package.

We also introduce a new development board called PCB120 which exists in
variants for VSC8584 and VSC8574 (and that's the only difference to the
best of my knowledge).

I suggest patches 1 to 3 go through net tree and patches 4 and 5 go
through MIPS tree. Patches going through net tree and those going through
MIPS tree do not depend on one another.

This patch series depends on this patch series:
(https://lore.kernel.org/lkml/20181008100728.24959-1-quentin.schulz@bootlin.com/)
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VSC8574 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with
the MAC via SGMII, QSGMII or 1000BASE-X, supports WOL, downshifting and
can set the blinking pattern of each of its 4 LEDs, supports SyncE as
well as HP Auto-MDIX detection.

This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
WOL, downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.

The VSC8574 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.

If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.

Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VSC8584 PHY is a 4-ports PHY that is 10/100/1000BASE-T, 100BASE-FX,
1000BASE-X and triple-speed copper SFP capable, can communicate with the
MAC via SGMII, QSGMII or 1000BASE-X, supports downshifting and can set
the blinking pattern of each of its 4 LEDs, supports hardware offloading
of MACsec and supports SyncE as well as HP Auto-MDIX detection.

This adds support for 10/100/1000BASE-T, SGMII/QSGMII link with the MAC,
downshifting, HP Auto-MDIX detection and blinking pattern for its 4
LEDs.

The VSC8584 has also an internal Intel 8051 microcontroller whose
firmware needs to be patched when the PHY is reset. If the 8051's
firmware has the expected CRC, its patching can be skipped. The
microcontroller can be accessed from any port of the PHY, though the CRC
function can only be done through the PHY that is the base PHY of the
package (internal address 0) due to a limitation of the firmware.

The GPIO register bank is a set of registers that are common to all PHYs
in the package. So any modification in any register of this bank affects
all PHYs of the package.

If the PHYs haven't been reset before booting the Linux kernel and were
configured to use interrupts for e.g. link status updates, it is
required to clear the interrupts mask register of all PHYs before being
able to use interrupts with any PHY. The first PHY of the package that
will be init will take care of clearing all PHYs interrupts mask
registers. Thus, we need to keep track of the init sequence in the
package, if it's already been done or if it's to be done.

Most of the init sequence of a PHY of the package is common to all PHYs
in the package, thus we use the SMI broadcast feature which enables us
to propagate a write in one register of one PHY to all PHYs in the same
package.

The revA of the VSC8584 PHY (which is not and will not be publicly
released) should NOT patch the firmware of the microcontroller or it'll
make things worse, the easiest way is just to not support it.
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The VSC8584 (and most likely other PHYs in the same generation) has two
additional LED modes that can be picked, so let's add them.
Reviewed-by: NRob Herring <robh@kernel.org>
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Quentin Schulz says:

====================
net: phy: mscc: various improvements to Microsemi PHY driver

The Microsemi PHYs have multiple banks of registers (called pages).
Registers can only be accessed from one page, if we need a register from
another page, we need to switch the page and the registers of all other
pages are not accessible anymore.

Basically, to read register 5 from page 0, 1, 2, etc., you do the same
phy_read(phydev, 5); but you need to set the desired page beforehand.

In order to guarantee that two concurrent functions do not change the
page, we need to do some locking per page. This can be achieved with the
use of phy_select_page and phy_restore_page functions but phy_write/read
calls in-between those two functions shall be replaced by their
lock-free alternative __phy_write/read.

The Microsemi PHYs have several counters so let's make them available as PHY
statistics.

The VSC 8530/31/40/41 also need to update their EEE init sequence in order to
avoid packet losses and improve performance.

This patch series also makes some minor cosmetic changes to the driver.

v3:
  - add reviewed-by,
  - use phy_read/write/modify_paged whenever possible instead of the
  combo phy_select_page, __phy_read/write/modify, phy_restore_page when
  only one __phy_read/write/modify was executed,

v2:
  - add patch to migrate MSCC driver to use phy_restore/select_page,
  - migrate all patches from v1 to use those two functions,
  - put the multiple lines of constants writes in an array and iterate over
  it to write the values,
  - add reviewed-bys,
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Here, the rc variable is either used only for the condition right after
the assignment or right before being used as the return value of the
function it's being used in.

So let's remove this unneeded temporary variable whenever possible.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

`if (x != 0)` is basically a more verbose version of `if (x)` so let's
use the latter so it's consistent throughout the whole driver.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The == operator precedes the || operator, so we can remove the
parenthesis around (a == b) || (c == d).

The condition is rather explicit and short so removing the parenthesis
definitely does not make it harder to read.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Microsemi PHYs (VSC 8530/31/40/41) need to update the Energy Efficient
Ethernet initialization sequence.
In order to avoid certain link state errors that could result in link
drops and packet loss, the physical coding sublayer (PCS) must be
updated with settings related to EEE in order to improve performance.
Reviewed-by: NFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microchip.com>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are a few counters available in the PHY: receive errors, false
carriers, link disconnects, media CRC errors and valids counters.

So let's expose those in the PHY driver.

Use the priv structure as the next PHY to be supported has a few
additional counters.
Reviewed-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NRaju Lakkaraju <Raju.Lakkaraju@microsemi.com>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The Microsemi PHYs have multiple banks of registers (called pages).
Registers can only be accessed from one page, if we need a register from
another page, we need to switch the page and the registers of all other
pages are not accessible anymore.

Basically, to read register 5 from page 0, 1, 2, etc., you do the same
phy_read(phydev, 5); but you need to set the desired page beforehand.

In order to guarantee that two concurrent functions do not change the
page, we need to do some locking per page. This can be achieved with the
use of phy_select_page and phy_restore_page functions but phy_write/read
calls in-between those two functions shall be replaced by their
lock-free alternative __phy_write/read.

Let's migrate this driver to those functions.
Suggested-by: NAndrew Lunn <andrew@lunn.ch>
Signed-off-by: NQuentin Schulz <quentin.schulz@bootlin.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to fix and improve dpaa2-ptp driver
in some places.

- Fixed the return for some functions.
- Replaced kzalloc with devm_kzalloc.
- Removed dev_set_drvdata(dev, NULL).
- Made ptp_dpaa2_caps const.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to removed unused code for dprtc.
This code will be re-added along with more features
of dpaa2-ptp added.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In dpaa2-ptp driver, it's odd to use rtc in names of
some functions and structures except these dprtc APIs.
This patch is to use ptp instead of rtc in names.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The NETDEVICES dependency and ETHERNET dependency hadn't
been required since dpaa2-eth was moved out of staging.
Also allowed COMPILE_TEST for dpaa2-eth.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The files maintained under DPAA2 PTP/ETHERNET needs to
be updated since dpaa2 ptp driver had been moved into
drivers/net/ethernet/freescale/dpaa2/.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is to move DPAA2 PTP driver out of staging/
since the dpaa2-eth had been moved out.
Signed-off-by: NYangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NTonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix 5 warnings and 14 checks issued by checkpatch.pl:

CHECK: Logical continuations should be on the previous line
+	if ((q->vars.qdelay < q->params.target / 2)
+	    && (q->vars.prob < MAX_PROB / 5))

WARNING: line over 80 characters
+		q->params.tupdate = usecs_to_jiffies(nla_get_u32(tb[TCA_PIE_TUPDATE]));

CHECK: Blank lines aren't necessary after an open brace '{'
+{
+

CHECK: braces {} should be used on all arms of this statement
+			if (qlen < QUEUE_THRESHOLD)
[...]
+			else {
[...]

CHECK: Unbalanced braces around else statement
+			else {

CHECK: No space is necessary after a cast
+	if (delta > (s32) (MAX_PROB / (100 / 2)) &&

CHECK: Unnecessary parentheses around 'qdelay == 0'
+	if ((qdelay == 0) && (qdelay_old == 0) && update_prob)

CHECK: Unnecessary parentheses around 'qdelay_old == 0'
+	if ((qdelay == 0) && (qdelay_old == 0) && update_prob)

CHECK: Unnecessary parentheses around 'q->vars.prob == 0'
+	if ((q->vars.qdelay < q->params.target / 2) &&
+	    (q->vars.qdelay_old < q->params.target / 2) &&
+	    (q->vars.prob == 0) &&
+	    (q->vars.avg_dq_rate > 0))

CHECK: Unnecessary parentheses around 'q->vars.avg_dq_rate > 0'
+	if ((q->vars.qdelay < q->params.target / 2) &&
+	    (q->vars.qdelay_old < q->params.target / 2) &&
+	    (q->vars.prob == 0) &&
+	    (q->vars.avg_dq_rate > 0))

CHECK: Blank lines aren't necessary before a close brace '}'
+
+}

CHECK: Comparison to NULL could be written "!opts"
+	if (opts == NULL)

CHECK: No space is necessary after a cast
+			((u32) PSCHED_TICKS2NS(q->params.target)) /

WARNING: line over 80 characters
+	    nla_put_u32(skb, TCA_PIE_TUPDATE, jiffies_to_usecs(q->params.tupdate)) ||

CHECK: Blank lines aren't necessary before a close brace '}'
+
+}

CHECK: No space is necessary after a cast
+		.delay		= ((u32) PSCHED_TICKS2NS(q->vars.qdelay)) /

WARNING: Missing a blank line after declarations
+	struct sk_buff *skb;
+	skb = qdisc_dequeue_head(sch);

WARNING: Missing a blank line after declarations
+	struct pie_sched_data *q = qdisc_priv(sch);
+	qdisc_reset_queue(sch);

WARNING: Missing a blank line after declarations
+	struct pie_sched_data *q = qdisc_priv(sch);
+	q->params.tupdate = 0;
Signed-off-by: NLeslie Monis <lesliemonis@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There is no need to compare *val.vu32* with < 0 because
such variable is of type u32 (32 bits, unsigned), making it
impossible to hold a negative value. Fix this by removing
such comparison.

Also, initialize variable *max_val* to -1, just in case
it is not initialized to either BNXT_MSIX_VEC_MAX or
BNXT_MSIX_VEC_MIN_MAX before using it in a comparison
with val.vu32 at line 159:

	if (val.vu32 > max_val)

Addresses-Coverity-ID: 1473915 ("Unsigned compared against 0")
Addresses-Coverity-ID: 1473920 ("Uninitialized scalar variable")
Signed-off-by: NGustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Merge tag 'wireless-drivers-next-for-davem-2018-10-07' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next

Kalle Valo says:

====================
wireless-drivers-next patches for 4.20

Second set of patches for 4.20. Heavy refactoring on mt76 continues
and the usual drivers in active development (iwlwifi, qtnfmac, ath10k)
getting new features. And as always, fixes and cleanup all over.

Major changes:

mt76

* more major refactoring to make it easier add new hardware support

* more work on mt76x0e support

* support for getting firmware version via ethtool

* add mt7650 PCI ID

iwlwifi

* HE radiotap cleanup and improvements

* reorder channel optimization for scans

* bump the FW API version

qtnfmac

* fixes for 'iw' output: rates for enabled SGI, 'dump station'

* expose more scan features to host: scan flush and dwell time

* inform cfg80211 when OBSS is not supported by firmware

wlcore

* add support for optional wakeirq

ath10k

* retrieve MAC address from system firmware if provided

* support extended board data download for dual-band QCA9984

* extended per sta tx statistics support via debugfs

* average ack rssi support for data frames

* speed up QCA6174 and QCA9377 firmware download using diag Copy
  Engine

* HTT High Latency mode support needed by SDIO and USB support

* get STA power save state via debugfs

ath9k

* add reset functionality for airtime station debugfs file
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

mt76 patches for 4.20

* unify code between mt76x0, mt76x2
* mt76x0 fixes
* another fix for rx buffer allocation regression on usb
* move mt76x2 source files to mt76x2 folder
* more work on mt76x0e support

Merge tag 'iwlwifi-next-for-kalle-2018-10-06' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next

Third set of iwlwifi patches for 4.20

* Fix for a race condition that caused the FW to crash;
* HE radiotap cleanup and improvements;
* Reorder channel optimization for scans;
* Bumped the FW API version supported after the last API change for
  this release;
* Debugging improvements;
* A few bug fixes;
* Some cleanups in preparation for a new implementation;
* Other small improvements, cleanups and fixes.

Dave writes:
  "Networking fixes:

  1) Fix truncation of 32-bit right shift in bpf, from Jann Horn.

  2) Fix memory leak in wireless wext compat, from Stefan Seyfried.

  3) Use after free in cfg80211's reg_process_hint(), from Yu Zhao.

  4) Need to cancel pending work when unbinding in smsc75xx otherwise
     we oops, also from Yu Zhao.

  5) Don't allow enslaving a team device to itself, from Ido Schimmel.

  6) Fix backwards compat with older userspace for rtnetlink FDB dumps.
     From Mauricio Faria.

  7) Add validation of tc policy netlink attributes, from David Ahern.

  8) Fix RCU locking in rawv6_send_hdrinc(), from Wei Wang."

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (26 commits)
  net: mvpp2: Extract the correct ethtype from the skb for tx csum offload
  ipv6: take rcu lock in rawv6_send_hdrinc()
  net: sched: Add policy validation for tc attributes
  rtnetlink: fix rtnl_fdb_dump() for ndmsg header
  yam: fix a missing-check bug
  net: bpfilter: Fix type cast and pointer warnings
  net: cxgb3_main: fix a missing-check bug
  bpf: 32-bit RSH verification must truncate input before the ALU op
  net: phy: phylink: fix SFP interface autodetection
  be2net: don't flip hw_features when VXLANs are added/deleted
  net/packet: fix packet drop as of virtio gso
  net: dsa: b53: Keep CPU port as tagged in all VLANs
  openvswitch: load NAT helper
  bnxt_en: get the reduced max_irqs by the ones used by RDMA
  bnxt_en: free hwrm resources, if driver probe fails.
  bnxt_en: Fix enables field in HWRM_QUEUE_COS2BW_CFG request
  bnxt_en: Fix VNIC reservations on the PF.
  team: Forbid enslaving team device to itself
  net/usb: cancel pending work when unbinding smsc75xx
  mlxsw: spectrum: Delete RIF when VLAN device is removed
  ...

As preparation for new trigger type, make iwl_fw_dbg_collect_desc
agnostic to the trigger structure.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

iwl_fw_dbg_collect can be called by any function that already
has the error string ready. iwl_fw_dbg_collect_trig, on the
other hand, does string formatting. The occurrences decrement
is at iwl_fw_dbg_collect_trig, instead of iwl_fw_dbg_collect,
which causes it to sometimes be skipped. Move it to the right
location.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

match_string() returns the index of an array for a matching string,
which can be used intead of open coded variant.
Reviewed-by: NAndy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: NYisheng Xie <xieyisheng1@huawei.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

As preparation for new trigger format, make the function
agnostic to the trigger fomat. Instead it gets the relevant
parameters - id and delay.
Signed-off-by: NSara Sharon <sara.sharon@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

For trigger-based PPDUs, most values aren't part of the HE-SIG-A
because they're preconfigured by the trigger frame. However, we
still have this information since we used the trigger frame to
configure the hardware, so we can (and do) read it back out and
can thus show it in radiotap.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

When the info type is MU, we still have the data from the TSF
overload words, so should decode that. When it's MU_EXT_INFO
we additionally have the SIG-B common 0/1/2 fields.

Also document the validity depending on the info type and fix
the name of the regular TB PPDU info type accordingly.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add debugfs to send host command in mvm and fmac op modes.
Allows to send host command at runtime via send_hcmd debugfs file.
The command is received as a string that represents hex values.

The struct of the command is as follows:
[cmd_id][flags][length][data]
cmd_id and flags are 8 chars long each.
length is 4 chars long.
data is length * 2 chars long.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Add send host command op to firmware runtime op struct to allow sending
host commands to the op mode from the fw runtime context.
Signed-off-by: NShahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>

Bump the firmware API version to 41.
Signed-off-by: NJohannes Berg <johannes.berg@intel.com>
Signed-off-by: NLuca Coelho <luciano.coelho@intel.com>