Skip to content

K
Kernel

openeuler / Kernel
大约 2 年 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 11 6月, 2020 2 次提交
  3. 01 2月, 2020 1 次提交
    • T
      x86/apic/msi: Plug non-maskable MSI affinity race · 6f1a4891
      由 Thomas Gleixner 提交于 
      Evan tracked down a subtle race between the update of the MSI message and
the device raising an interrupt internally on PCI devices which do not
support MSI masking. The update of the MSI message is non-atomic and
consists of either 2 or 3 sequential 32bit wide writes to the PCI config
space.

   - Write address low 32bits
   - Write address high 32bits (If supported by device)
   - Write data

When an interrupt is migrated then both address and data might change, so
the kernel attempts to mask the MSI interrupt first. But for MSI masking is
optional, so there exist devices which do not provide it. That means that
if the device raises an interrupt internally between the writes then a MSI
message is sent built from half updated state.

On x86 this can lead to spurious interrupts on the wrong interrupt
vector when the affinity setting changes both address and data. As a
consequence the device interrupt can be lost causing the device to
become stuck or malfunctioning.

Evan tried to handle that by disabling MSI accross an MSI message
update. That's not feasible because disabling MSI has issues on its own:

 If MSI is disabled the PCI device is routing an interrupt to the legacy
 INTx mechanism. The INTx delivery can be disabled, but the disablement is
 not working on all devices.

 Some devices lose interrupts when both MSI and INTx delivery are disabled.

Another way to solve this would be to enforce the allocation of the same
vector on all CPUs in the system for this kind of screwed devices. That
could be done, but it would bring back the vector space exhaustion problems
which got solved a few years ago.

Fortunately the high address (if supported by the device) is only relevant
when X2APIC is enabled which implies interrupt remapping. In the interrupt
remapping case the affinity setting is happening at the interrupt remapping
unit and the PCI MSI message is programmed only once when the PCI device is
initialized.

That makes it possible to solve it with a two step update:

  1) Target the MSI msg to the new vector on the current target CPU

  2) Target the MSI msg to the new vector on the new target CPU

In both cases writing the MSI message is only changing a single 32bit word
which prevents the issue of inconsistency.

After writing the final destination it is necessary to check whether the
device issued an interrupt while the intermediate state #1 (new vector,
current CPU) was in effect.

This is possible because the affinity change is always happening on the
current target CPU. The code runs with interrupts disabled, so the
interrupt can be detected by checking the IRR of the local APIC. If the
vector is pending in the IRR then the interrupt is retriggered on the new
target CPU by sending an IPI for the associated vector on the target CPU.

This can cause spurious interrupts on both the local and the new target
CPU.

 1) If the new vector is not in use on the local CPU and the device
    affected by the affinity change raised an interrupt during the
    transitional state (step #1 above) then interrupt entry code will
    ignore that spurious interrupt. The vector is marked so that the
    'No irq handler for vector' warning is supressed once.

 2) If the new vector is in use already on the local CPU then the IRR check
    might see an pending interrupt from the device which is using this
    vector. The IPI to the new target CPU will then invoke the handler of
    the device, which got the affinity change, even if that device did not
    issue an interrupt

 3) If the new vector is in use already on the local CPU and the device
    affected by the affinity change raised an interrupt during the
    transitional state (step #1 above) then the handler of the device which
    uses that vector on the local CPU will be invoked.

expose issues in device driver interrupt handlers which are not prepared to
handle a spurious interrupt correctly. This not a regression, it's just
exposing something which was already broken as spurious interrupts can
happen for a lot of reasons and all driver handlers need to be able to deal
with them.
Reported-by: NEvan Green <evgreen@chromium.org>
Debugged-by: NEvan Green <evgreen@chromium.org>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NEvan Green <evgreen@chromium.org>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/87imkr4s7n.fsf@nanos.tec.linutronix.de
      6f1a4891
  5. 29 1月, 2020 1 次提交
  7. 25 7月, 2019 5 次提交
  9. 17 7月, 2019 1 次提交
    • Q
      x86/apic: Silence -Wtype-limits compiler warnings · ec633558
      由 Qian Cai 提交于 
      There are many compiler warnings like this,

In file included from ./arch/x86/include/asm/smp.h:13,
                 from ./arch/x86/include/asm/mmzone_64.h:11,
                 from ./arch/x86/include/asm/mmzone.h:5,
                 from ./include/linux/mmzone.h:969,
                 from ./include/linux/gfp.h:6,
                 from ./include/linux/mm.h:10,
                 from arch/x86/kernel/apic/io_apic.c:34:
arch/x86/kernel/apic/io_apic.c: In function 'check_timer':
./arch/x86/include/asm/apic.h:37:11: warning: comparison of unsigned
expression >= 0 is always true [-Wtype-limits]
   if ((v) <= apic_verbosity) \
           ^~
arch/x86/kernel/apic/io_apic.c:2160:2: note: in expansion of macro
'apic_printk'
  apic_printk(APIC_QUIET, KERN_INFO "..TIMER: vector=0x%02X "
  ^~~~~~~~~~~
./arch/x86/include/asm/apic.h:37:11: warning: comparison of unsigned
expression >= 0 is always true [-Wtype-limits]
   if ((v) <= apic_verbosity) \
           ^~
arch/x86/kernel/apic/io_apic.c:2207:4: note: in expansion of macro
'apic_printk'
    apic_printk(APIC_QUIET, KERN_ERR "..MP-BIOS bug: "
    ^~~~~~~~~~~

APIC_QUIET is 0, so silence them by making apic_verbosity type int.
Signed-off-by: NQian Cai <cai@lca.pw>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Link: https://lkml.kernel.org/r/1562621805-24789-1-git-send-email-cai@lca.pw
      ec633558
  11. 29 6月, 2019 1 次提交
    • T
      x86/timer: Skip PIT initialization on modern chipsets · c8c40767
      由 Thomas Gleixner 提交于 
      Recent Intel chipsets including Skylake and ApolloLake have a special
ITSSPRC register which allows the 8254 PIT to be gated.  When gated, the
8254 registers can still be programmed as normal, but there are no IRQ0
timer interrupts.

Some products such as the Connex L1430 and exone go Rugged E11 use this
register to ship with the PIT gated by default. This causes Linux to fail
to boot:

  Kernel panic - not syncing: IO-APIC + timer doesn't work! Boot with
  apic=debug and send a report.

The panic happens before the framebuffer is initialized, so to the user, it
appears as an early boot hang on a black screen.

Affected products typically have a BIOS option that can be used to enable
the 8254 and make Linux work (Chipset -> South Cluster Configuration ->
Miscellaneous Configuration -> 8254 Clock Gating), however it would be best
to make Linux support the no-8254 case.

Modern sytems allow to discover the TSC and local APIC timer frequencies,
so the calibration against the PIT is not required. These systems have
always running timers and the local APIC timer works also in deep power
states.

So the setup of the PIT including the IO-APIC timer interrupt delivery
checks are a pointless exercise.

Skip the PIT setup and the IO-APIC timer interrupt checks on these systems,
which avoids the panic caused by non ticking PITs and also speeds up the
boot process.

Thanks to Daniel for providing the changelog, initial analysis of the
problem and testing against a variety of machines.
Reported-by: NDaniel Drake <drake@endlessm.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NDaniel Drake <drake@endlessm.com>
Cc: bp@alien8.de
Cc: hpa@zytor.com
Cc: linux@endlessm.com
Cc: rafael.j.wysocki@intel.com
Cc: hdegoede@redhat.com
Link: https://lkml.kernel.org/r/20190628072307.24678-1-drake@endlessm.com
      c8c40767
  13. 17 6月, 2019 1 次提交
  15. 31 5月, 2019 1 次提交
  17. 09 5月, 2019 1 次提交
  19. 05 8月, 2018 1 次提交
  21. 02 7月, 2018 1 次提交
    • T
      Revert "x86/apic: Ignore secondary threads if nosmt=force" · 506a66f3
      由 Thomas Gleixner 提交于 
      Dave Hansen reported, that it's outright dangerous to keep SMT siblings
disabled completely so they are stuck in the BIOS and wait for SIPI.

The reason is that Machine Check Exceptions are broadcasted to siblings and
the soft disabled sibling has CR4.MCE = 0. If a MCE is delivered to a
logical core with CR4.MCE = 0, it asserts IERR#, which shuts down or
reboots the machine. The MCE chapter in the SDM contains the following
blurb:

    Because the logical processors within a physical package are tightly
    coupled with respect to shared hardware resources, both logical
    processors are notified of machine check errors that occur within a
    given physical processor. If machine-check exceptions are enabled when
    a fatal error is reported, all the logical processors within a physical
    package are dispatched to the machine-check exception handler. If
    machine-check exceptions are disabled, the logical processors enter the
    shutdown state and assert the IERR# signal. When enabling machine-check
    exceptions, the MCE flag in control register CR4 should be set for each
    logical processor.

Reverting the commit which ignores siblings at enumeration time solves only
half of the problem. The core cpuhotplug logic needs to be adjusted as
well.

This thoughtful engineered mechanism also turns the boot process on all
Intel HT enabled systems into a MCE lottery. MCE is enabled on the boot CPU
before the secondary CPUs are brought up. Depending on the number of
physical cores the window in which this situation can happen is smaller or
larger. On a HSW-EX it's about 750ms:

MCE is enabled on the boot CPU:

[    0.244017] mce: CPU supports 22 MCE banks

The corresponding sibling #72 boots:

[    1.008005] .... node  #0, CPUs:    #72

That means if an MCE hits on physical core 0 (logical CPUs 0 and 72)
between these two points the machine is going to shutdown. At least it's a
known safe state.

It's obvious that the early boot can be hit by an MCE as well and then runs
into the same situation because MCEs are not yet enabled on the boot CPU.
But after enabling them on the boot CPU, it does not make any sense to
prevent the kernel from recovering.

Adjust the nosmt kernel parameter documentation as well.

Reverts: 2207def7 ("x86/apic: Ignore secondary threads if nosmt=force")
Reported-by: NDave Hansen <dave.hansen@intel.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NTony Luck <tony.luck@intel.com>
      506a66f3
  23. 21 6月, 2018 2 次提交
    • T
      x86/apic: Ignore secondary threads if nosmt=force · 2207def7
      由 Thomas Gleixner 提交于 
      nosmt on the kernel command line merely prevents the onlining of the
secondary SMT siblings.

nosmt=force makes the APIC detection code ignore the secondary SMT siblings
completely, so they even do not show up as possible CPUs. That reduces the
amount of memory allocations for per cpu variables and saves other
resources from being allocated too large.

This is not fully equivalent to disabling SMT in the BIOS because the low
level SMT enabling in the BIOS can result in partitioning of resources
between the siblings, which is not undone by just ignoring them. Some CPUs
can use the full resources when their sibling is not onlined, but this is
depending on the CPU family and model and it's not well documented whether
this applies to all partitioned resources. That means depending on the
workload disabling SMT in the BIOS might result in better performance.

Linus analysis of the Intel manual:

  The intel optimization manual is not very clear on what the partitioning
  rules are.

  I find:

    "In general, the buffers for staging instructions between major pipe
     stages  are partitioned. These buffers include µop queues after the
     execution trace cache, the queues after the register rename stage, the
     reorder buffer which stages instructions for retirement, and the load
     and store buffers.

     In the case of load and store buffers, partitioning also provided an
     easier implementation to maintain memory ordering for each logical
     processor and detect memory ordering violations"

  but some of that partitioning may be relaxed if the HT thread is "not
  active":

    "In Intel microarchitecture code name Sandy Bridge, the micro-op queue
     is statically partitioned to provide 28 entries for each logical
     processor,  irrespective of software executing in single thread or
     multiple threads. If one logical processor is not active in Intel
     microarchitecture code name Ivy Bridge, then a single thread executing
     on that processor  core can use the 56 entries in the micro-op queue"

  but I do not know what "not active" means, and how dynamic it is. Some of
  that partitioning may be entirely static and depend on the early BIOS
  disabling of HT, and even if we park the cores, the resources will just be
  wasted.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
      2207def7
    • T
      x86/smp: Provide topology_is_primary_thread() · 6a4d2657
      由 Thomas Gleixner 提交于 
      If the CPU is supporting SMT then the primary thread can be found by
checking the lower APIC ID bits for zero. smp_num_siblings is used to build
the mask for the APIC ID bits which need to be taken into account.

This uses the MPTABLE or ACPI/MADT supplied APIC ID, which can be different
than the initial APIC ID in CPUID. But according to AMD the lower bits have
to be consistent. Intel gave a tentative confirmation as well.

Preparatory patch to support disabling SMT at boot/runtime.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Reviewed-by: NKonrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Acked-by: NIngo Molnar <mingo@kernel.org>
      6a4d2657
  25. 06 6月, 2018 1 次提交
    • T
      x86/apic: Provide apic_ack_irq() · c0255770
      由 Thomas Gleixner 提交于 
      apic_ack_edge() is explicitely for handling interrupt affinity cleanup when
interrupt remapping is not available or disable.

Remapped interrupts and also some of the platform specific special
interrupts, e.g. UV, invoke ack_APIC_irq() directly.

To address the issue of failing an affinity update with -EBUSY the delayed
affinity mechanism can be reused, but ack_APIC_irq() does not handle
that. Adding this to ack_APIC_irq() is not possible, because that function
is also used for exceptions and directly handled interrupts like IPIs.

Create a new function, which just contains the conditional invocation of
irq_move_irq() and the final ack_APIC_irq().

Reuse the new function in apic_ack_edge().

Preparatory change for the real fix.

Fixes: dccfe314 ("x86/vector: Simplify vector move cleanup")
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NSong Liu <songliubraving@fb.com>
Cc: Joerg Roedel <jroedel@suse.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Song Liu <liu.song.a23@gmail.com>
Cc: Dmitry Safonov <0x7f454c46@gmail.com>
Cc: stable@vger.kernel.org
Cc: Mike Travis <mike.travis@hpe.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Tariq Toukan <tariqt@mellanox.com>
Link: https://lkml.kernel.org/r/20180604162224.471925894@linutronix.de
      c0255770
  27. 10 4月, 2018 1 次提交
    • L
      x86/apic: Fix signedness bug in APIC ID validity checks · a774635d
      由 Li RongQing 提交于 
      The APIC ID as parsed from ACPI MADT is validity checked with the
apic->apic_id_valid() callback, which depends on the selected APIC type.

For non X2APIC types APIC IDs >= 0xFF are invalid, but values > 0x7FFFFFFF
are detected as valid. This happens because the 'apicid' argument of the
apic_id_valid() callback is type 'int'. So the resulting comparison

   apicid < 0xFF

evaluates to true for all unsigned int values > 0x7FFFFFFF which are handed
to default_apic_id_valid(). As a consequence, invalid APIC IDs in !X2APIC
mode are considered valid and accounted as possible CPUs.

Change the apicid argument type of the apic_id_valid() callback to u32 so
the evaluation is unsigned and returns the correct result.

[ tglx: Massaged changelog ]
Signed-off-by: NLi RongQing <lirongqing@baidu.com>
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Cc: jgross@suse.com
Cc: Dou Liyang <douly.fnst@cn.fujitsu.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: hpa@zytor.com
Link: https://lkml.kernel.org/r/1523322966-10296-1-git-send-email-lirongqing@baidu.com
      a774635d
  29. 26 3月, 2018 1 次提交
  31. 16 2月, 2018 1 次提交
  33. 14 2月, 2018 1 次提交
  35. 14 1月, 2018 1 次提交
  37. 26 9月, 2017 11 次提交
    • T
      x86/irq: Simplify hotplug vector accounting · 2cffad7b
      由 Thomas Gleixner 提交于 
      Before a CPU is taken offline the number of active interrupt vectors on the
outgoing CPU and the number of vectors which are available on the other
online CPUs are counted and compared. If the active vectors are more than
the available vectors on the other CPUs then the CPU hot-unplug operation
is aborted. This again uses loop based search and is inaccurate.

The bitmap matrix allocator has accurate accounting information and can
tell exactly whether the vector space is sufficient or not.

Emit a message when the number of globaly reserved (unallocated) vectors is
larger than the number of available vectors after offlining a CPU because
after that point request_irq() might fail.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213156.351193962@linutronix.de
      2cffad7b
    • T
      x86/irq/vector: Initialize matrix allocator · 0fa115da
      由 Thomas Gleixner 提交于 
      Initialize the matrix allocator and add the proper accounting points to the
code.

No functional change, just preparation.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213155.108410660@linutronix.de
      0fa115da
    • T
      x86/apic: Add replacement for cpu_mask_to_apicid() · 9f9e3bb1
      由 Thomas Gleixner 提交于 
      As preparation for replacing the vector allocator, provide a new function
which takes a cpu number instead of a cpu mask to calculate/lookup the
resulting APIC destination id.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
      9f9e3bb1
    • T
      x86/apic: Get rid of apic->target_cpus · c1d1ee9a
      由 Thomas Gleixner 提交于 
      The target_cpus() callback of the apic struct is not really useful. Some
APICs return cpu_online_mask and others cpus_all_mask. The latter is bogus
as it does not take holes in the cpus_possible_mask into account.

Replace it with cpus_online_mask which makes the most sense and remove the
callback.

The usage sites will be removed in a later step anyway, so get rid of it
now to have incremental changes.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213154.070850916@linutronix.de
      c1d1ee9a
    • T
      x86/apic: Reorganize struct apic · 72f48a38
      由 Thomas Gleixner 提交于 
      struct apic has just grown over time by adding function pointers in random
places. Reorganize it so it becomes more cache line friendly.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.913642524@linutronix.de
      72f48a38
    • T
      x86/apic: Move common APIC callbacks · 83a10522
      由 Thomas Gleixner 提交于 
      Move more apic struct specific functions out of the header and the apic
management code into the common source file.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.834421893@linutronix.de
      83a10522
    • T
      x86/apic: Sanitize 32/64bit APIC callbacks · 64063505
      由 Thomas Gleixner 提交于 
      The 32bit and the 64bit implementation of default_cpu_present_to_apicid()
and default_check_phys_apicid_present() are exactly the same, but
implemented and located differently.

Move them to common apic code and get rid of the pointless difference.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.757329991@linutronix.de
      64063505
    • T
      x86/apic: Move APIC noop specific functions · 1da91779
      由 Thomas Gleixner 提交于 
      Move more inlines to the place where they belong.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.677743545@linutronix.de
      1da91779
    • T
      x86/apic: Move probe32 specific APIC functions · 0801bbaa
      由 Thomas Gleixner 提交于 
      The apic functions which are used in probe_32.c are implemented as inlines
or in apic.c. There is no reason to have them at random places.

Move them to the actual usage site and make them static.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.596768194@linutronix.de
      0801bbaa
    • T
      x86/apic: Sanitize return value of check_apicid_used() · 57e0aa44
      由 Thomas Gleixner 提交于 
      The check is boolean, but the function returns unsigned long for no value.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.516730518@linutronix.de
      57e0aa44
    • T
      x86/apic: Sanitize return value of apic.set_apic_id() · 727657e6
      由 Thomas Gleixner 提交于 
      The set_apic_id() callback returns an unsigned long value which is handed
in to apic_write() as the value argument u32.

Adjust the return value so it returns u32 right away.
Signed-off-by: NThomas Gleixner <tglx@linutronix.de>
Tested-by: NJuergen Gross <jgross@suse.com>
Tested-by: NYu Chen <yu.c.chen@intel.com>
Acked-by: NJuergen Gross <jgross@suse.com>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Alok Kataria <akataria@vmware.com>
Cc: Joerg Roedel <joro@8bytes.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Rui Zhang <rui.zhang@intel.com>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: Dan Williams <dan.j.williams@intel.com>
Cc: Len Brown <lenb@kernel.org>
Link: https://lkml.kernel.org/r/20170913213153.437208268@linutronix.de
      727657e6
  39. 25 9月, 2017 5 次提交