seagate_st0x_detect() can become static.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- #include <asm/irq.h> for getting the prototypes of {dis,en}able_irq()

- make the needlessly global wd33c93_setup() static
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch contains the following cleanups:
- make needlessly global functions static
- every file should #include the headers containing the prototypes for
  it's global functions
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

lockdep noticed that with ATA support the port->dev_list_lock was
entangled at irq context, so it now needs to become IRQ safe
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This one was noticed by Gilbert Wu of Adaptec:

The libata core actually does the DMA mapping for you, so there has to
be an exception in the device drivers that *don't* do dma mapping for
ATA commands.  However, since we've already done this, libsas must now
dma map any ATA commands that it wishes to issue ... and yes, this is a
horrible mess.

Additionally, the test in aic94xx for ATA protocols isn't quite right.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

ATA devices need special handling for sas_task_abort.  If the ATA command
came from SCSI, then we merely need to tell SCSI to abort the scsi_cmnd.
However, internal commands require a bit more work--we need to fill the qc
with the appropriate error status and complete the command, and eventually
post_internal will issue the actual ABORT TASK.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The SATL should connect the scsi_cmnd to the sas_task (despite the presence
of libata) so that requests to abort scsi_cmnds headed to the ATA device
can be processed by the EH and aborted correctly.  The abort status should
still be propagated from sas -> ata -> scsi.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

When libsas encounters a STP device whose protocol isn't recognized (i.e.
not ATA or ATAPI), we should set the ata_device's class to ATA_DEV_UNKNOWN
instead of ATA_DEV_ATA.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

A sas_task sent to an ATAPI devices returns SAM_GOOD if successful.
Therefore, we should treat this the same way we treat ATA commands
that succeed.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Since the aic94xx sequencer assigns its own NCQ tags to ATA commands, it
no longer makes any sense to copy the sactive field in the STP response
to ata_port->sactive, as that will confuse libata.  Also, libata seems
to be capable of managing sactive on its own.

The attached patch gets rid of one of the causes of the BUG messages in
ata_qc_new, and seems to work without problems on an IBM x206m.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch adds a new field, lldd_task, to ata_queued_cmd so that libata
users such as libsas can associate some data with a qc.  The particular
ambition with this patch is to associate a sas_task with a qc; that way,
if libata decides to timeout a command, we can come back (in
sas_ata_post_internal) and abort the sas task.

One question remains: Is it necessary to reset the phy on error, or will
the libata error handler take care of it?  (Assuming that one is written,
of course.)  This patch, as it is today, works well enough to clean
things up when an ATA device probe attempt fails halfway through the probe,
though I'm not sure this is always the right thing to do.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The sas_ata_qc_issue function was incorrectly written to return error
codes such as -ENOMEM.  Since libata OR's qc->err_mask with the
return value, It is necessary to make my code return one of the
AC_ERR_ codes instead.  For now, use AC_ERR_SYSTEM because an error
here means that the OS couldn't send the command to the controller.

If anybody has a suggestion for a better AC_ERR_ code to use, please
suggest it.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

ata_qc_complete and ata_sas_queuecmd require that the port lock be held
when they are called.  sas_ata doesn't do this, leading to BUG messages
about qc tags newly allocated qc tags already being in use.  This patch
fixes the locking, which should clean up the rest of those messages.

So far I've tested this against an IBM x206m with two SATA disks with no
BUG messages and no other signs of things going wrong, and the machine
finally passed the pounder stress test.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

It turns out that libata has already dma_map_sg'd the scatterlist
entries that go with an ata_queued_cmd by the time it calls
sas_ata_qc_issue.  sas_ata_qc_issue passes this scatterlist to aic94xx.
Unfortunately, aic94xx assumes that any scatterlist passed to it needs
to be pci_map_sg'd... which blows away the mapping that libata created!
This causes (on a x260) Calgary IOMMU table leaks and duplicate frees
when aic94xx and libata try to {pci,dma}_unmap_sg the scatterlist.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>

Key this check off ATA_PROTOCOL_STP
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This is a respin of my earlier patch that migrates the ATA support code
into a separate file.  For now, the controversial linking bits have
been removed per James Bottomley's request for a patch that contains
only the migration diffs, which means that libsas continues to require
libata.  I intend to address that problem in a separate patch.

This patch is against the aic94xx-sas-2.6 git tree, and it has been
sanity tested on my x206m with Seagate SATA and SAS disks without
uncovering any new problems.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

We actually had two problems: the one with the tag (which is fixed by
zeroing the tag before sending the taskfile to the sequencer) but the
other with the fact that we sent our first NCQ command to the device
before the sequencer had been informed of the NCQ tagging
capabilities.  I fixed the latter by moving the rphy_add() to the
correct point in the code after the NCQ capabilities are set up.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This replaces a few BUG_ON() statements with the correct failure error
handling.  There are still many more to do.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

It turns out this is fairly easy to plumb in by recognising the three
command types and copying the CDB.  The protocol response path needs to
be amended to cope with SAS_PROTO_RESPONSE.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch adds SATAII NCQ support to libsas.  Both the use_ncq and the
dma_xfer flags in ata_task must be set for NCQ to work correctly on the
Adaptec SAS controller.  The rest of the patch adds ATA_FLAG_NCQ to
sata_port_info and sets up ap->scsi_host so that ata_setup_ncq doesn't
crash.  Please note that this patch is against the aic94xx-sas git tree,
not scsi-misc.  Thanks also to James Bottomley for providing an earlier
version of this patch from which to work.

I've tested this patch on a x206m with a ST380819AS SATA2 disk plugged
into the Adaptec SAS controller.  The drive came up with a queue depth
of 31, and I successfully ran an I/O flood test to coerce libata into
sending multiple commands simultaneously.  A kernel probe recorded the
maximum tag number that had been seen before and after the flood test;
before the test it was 2 and after it was 30, as I expected.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The aic94xx controller has a bitmask establishing which tags are ok to
use with a SATA NCQ disk.  When the queue depth is 32, however, the
expression that is used sets the mask to zero, not 0xFFFFFFFF.
This patch widens the width of the integer so that this case is handled
properly.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The prototype of this has changed for the link speed setting patch.
Need to update the SATA use of this.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch adds support for SATA over SAS expanders to the previous two
SATA support in libsas patches.

There were a couple of nasty non trivial things to sort out before this
one could be made to work.

Firstly, I'd like to thank Doug Gilbert for diagnosing a problem with
the LSI expanders where the REPORT_SATA_PHY command was returning the
D2H FIS in the wrong order (Although, here, I think I have to blame the
SAS standards which specifies the FIS "shall be returned in little
endian format" and later on "which means resp[24] shall be FIS type"
The latter, of course, implying big endian format).  Just to make sure,
I put a check for the D2H FIS type being in the wrong position and
reverse the FIS data if it is.

The second is a problem outlined in Annex G of the SAS standard (again,
a technical point with D2H FIS ... necessitating a phy reset on certain
conditions).

With the patch, I can now see my SATA-1 disk in a cascaded expander
configuration.
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Hook the scsi_host_template functions in libsas to delegate
functionality to libata when appropriate.
Signed-off-by: NDarrick J. Wong <djwong@us.ibm.com>

Misc code changes and merge fixes and update for libata->drivers/ata
move
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Currently, the freezer treats all tasks as freezable, except for the kernel
threads that explicitly set the PF_NOFREEZE flag for themselves.  This
approach is problematic, since it requires every kernel thread to either
set PF_NOFREEZE explicitly, or call try_to_freeze(), even if it doesn't
care for the freezing of tasks at all.

It seems better to only require the kernel threads that want to or need to
be frozen to use some freezer-related code and to remove any
freezer-related code from the other (nonfreezable) kernel threads, which is
done in this patch.

The patch causes all kernel threads to be nonfreezable by default (ie.  to
have PF_NOFREEZE set by default) and introduces the set_freezable()
function that should be called by the freezable kernel threads in order to
unset PF_NOFREEZE.  It also makes all of the currently freezable kernel
threads call set_freezable(), so it shouldn't cause any (intentional)
change of behaviour to appear.  Additionally, it updates documentation to
describe the freezing of tasks more accurately.

[akpm@linux-foundation.org: build fixes]
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NNigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Gautham R Shenoy <ego@in.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Make some offending drivers depend on it and set CONFIG_ARCH_NO_VIRT_TO_BUS
for ppc64 so that we don't build those drivers.

This gets PowerPC allmodconfig and allyesconfig much closer to building.
Signed-off-by: NStephen Rothwell <sfr@canb.auug.org.au>
Cc: Al Viro <viro@ftp.linux.org.uk>
Acked-by: NDavid Miller <davem@davemloft.net>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

bsg uses scsi_cmd_ioctl() for some SCSI/sg ioctl
commands. scsi_cmd_ioctl() gets a request queue from a gendisk
arguement. This prevents bsg being bound to SCSI devices that don't
have a gendisk (like OSD). This adds a request_queue argument to
scsi_cmd_ioctl(). The SCSI/sg ioctl commands doesn't use a gendisk so
it's safe for any SCSI devices to use scsi_cmd_ioctl().
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: NJens Axboe <jens.axboe@oracle.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Santiago Leon <santil@us.ibm.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- remove the unnecessary map_single path.

- convert to use the new accessors for the sg lists and the
parameters.

Jens Axboe <jens.axboe@oracle.com> did the for_each_sg cleanup.
Signed-off-by: NFUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Add printk levels
Clean up some oddities of formatting
Fix goto labels
Signed-off-by: NAlan Cox <alan@redhat.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

drivers/scsi/aic7xxx_old.c:aic7xxx_slave_alloc() unnecessarily passes
GFP_ATOMIC (along with GFP_KERNEL) to kmalloc() from a context that is not
atomic. Remove the pointless GFP_ATOMIC.
Signed-off-by: NSatyam Sharma <ssatyam@cse.iitk.ac.in>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Cc: Doug Ledford <dledford@redhat.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Not converted to the 2.6 kconfig system and no code in the tree.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

With

 dma-mapping-prevent-dma-dependent-code-from-linking-on.patch

scsi fails to build on !HAS_DMA architectures:

drivers/built-in.o(.text+0x20af6): In function `scsi_dma_map':
: undefined reference to `dma_map_sg'
drivers/built-in.o(.text+0x20b5c): In function `scsi_dma_unmap':
: undefined reference to `dma_unmap_sg'

I split those functions out into a new file. Builds on s390 and i386.

Move scsi_dma_{map,unmap} into scsi_lib_dma.c which is only build if
HAS_DMA is set.
Signed-off-by: NCornelia Huck <cornelia.huck@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: James Bottomley <James.Bottomley@SteelEye.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

This patch tidies up scsi_add_lun a bit.  I rewrote the kerneldoc to match
the actual parameters, moved the check for RBC and MMC REPORT_LUN devices
away from the switch(), changed the setup of sdev->type to account for
BLIST_ISROM, moved the check for BLIST_NO_ULD_ATTACH further down in
the function, removed a bogus comment and fixed some whitespace issues.
Signed-off-by: NMatthew Wilcox <matthew@wil.cx>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

remove printk, which triggers because of low scsi clock on SNI RMs
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

- base address is now a physical address; no need to convert it
- remove not needed error printk in module init function
Signed-off-by: NThomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

On Wed, 2007-06-06 at 11:55 -0700, David C Somayajulu wrote:
This patch fixes the code handling underrun and overrun conditions.
Also fixed coding style as per Mike Christie's advice.
Signed-off-by: NDavid Somayajulu <david.somayajulu@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

The Megaraid Mailbox driver uses a semaphore as mutex.  Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Acked-by: N"Patro, Sumant" <Sumant.Patro@lsi.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>

Following patch bump up the driver version reflecting NPIV addition to
the qla2xxx.

- version changed from 8.01.07-k7 to 8.02.00-k1.
Signed-off-by: NSeokmann Ju <seokmann.ju@qlogic.com>
Signed-off-by: NJames Bottomley <James.Bottomley@SteelEye.com>