Use the generic gpiolib gpio_is_valid() function to test
if the phy IRQ line GPIO is actually provided.

For non-connected or non-existing phy IRQ lines, -EINVAL
value is used for phy_irq_pin field of struct at91_eth_data.
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>

Allow the device tree to provide the mac address and the phy mode.
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
[nicolas.ferre@atmel.com: change "compatible" node property, doc and DT hwaddr]
Signed-off-by: NNicolas Ferre <nicolas.ferre@atmel.com>
[jamie@jamieiles.com: add "gem" compatibility strings and doc]
Acked-by: Jamie Iles<jamie@jamieiles.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>

Revert a hunk in drivers/net/wireless/ath/ath9k/hw.c introduced by
commit 2577c6e8 ("ath9k_hw: Add support for AR946/8x chipsets") that
caused a nasty regression to appear on my Acer Ferrari One (the box
locks up entirely at random times after the wireless has been started
without any way to get debug information out of it).
Signed-off-by: NRafael J. Wysocki <rjw@sisk.pl>
Acked-by: NFelix Fietkau <nbd@openwrt.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

GEM has configurable receive buffer sizes so requires this to be
programmed up.  Any size < 2048 and a multiple of 64 bytes is permitted.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Some GEM implementations may support DMA bus widths up to 128 bits.  We
can get the maximum supported DMA bus width from the design
configuration register so use that to program the device up.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

GEM devices have a different number of statistics registers and they
are at a different offset to MACB devices.  Make the statistics
collection method dependent on device type.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

GEM devices support larger clock divisors and have a different
range of divisors.  Program the MDIO clock divisors based on the
device type.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

The Cadence GEM is based on the MACB Ethernet controller but has a few
small changes with regards to register and bitfield placement.  This
patch detects the presence of a GEM by reading the module ID register
and setting a flag appropriately.

This handles the new HW address, USRIO and hash register base register
locations in GEM.

v3: - convert to macb_is_gem() inline rather than storing a boolean
      flag
    - handle rx_overrun stats for gem
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Cc: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

macb is already using the dev_dbg() and friends helpers so use netdev_()
along with a pr_fmt() definition to make the printing a little cleaner.
Acked-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

Both at91 and avr32 defines its own platform data structure for
the macb driver and both share common structures though at91
includes a currently unused phy_irq_pin.  Create a common
macb_platform_data for macb that both at91 and avr32 can use.  In
future we can use this to support other architectures that use the
same IP block with the macb driver.

v2: rename eth_platform_data to macb_platform_data and allow at91_ether
to share the platform data with macb.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

AT91 now provides both "pclk" and "hclk" aliases for the the macb
device so we can use the same clk handling paths for both AT91 and
AVR32.
Signed-off-by: NJamie Iles <jamie@jamieiles.com>
Acked-by: NDavid S. Miller <davem@davemloft.net>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Tested-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>

If IRQ was never initialized, then calling napi_disable() would hang.
Add more bookkeeping to track whether IRQ was ever initialized.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The hardware has a restriction that the minimum ring size possible
is 128. The number of elements used is controlled by tx_pending and
the overall number of elements in the ring tx_ring_size, therefore it
is okay to limit the number of elements in use to a small value (63)
but still provide a bigger ring.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When changing mode via bonding's sysfs, the slaves are not initialized
correctly. Forbid to change modes with slaves present to ensure that every
slave is initialized correctly via bond_enslave().
Signed-off-by: NVeaceslav Falico <vfalico@redhat.com>
Signed-off-by: NAndy Gospodarek <andy@greyhouse.net>
Acked-by: NNicolas de Pesloüan <nicolas.2p.debian@free.fr>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the pm functions to avoid the system
sleeps while a spinlock is taken.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes un-needed spin_lock in stmmac_ioctl while reading and
writing mdio registers. While holding spin_lock the code must be
atomic, which is not true in this case as both mdiobus_read and writes
have mutex locks.

Without this patch reading mdio registers via mii-tool results in below
BUG:
mii-tool -vvv eth0"
Using SIOCGMIIPHY=0x8947
BUG: sleeping function called from invalid context at kernel/mutex.c:287
in_atomic(): 1, irqs_disabled(): 0, pid: 614, name: mii-tool
2 locks held by mii-tool/614:
 #0:  (rtnl_mutex){......}, at: [<c01fd80c>] dev_ioctl+0x550/0x674
 #1:  (&priv->lock){......}, at: [<c01b34ec>] stmmac_ioctl+0x4c/0x78
[<c002ea14>] (unwind_backtrace+0x0/0xcc) from [<c0272c38>]
(mutex_lock_nested+0x24/0x35c)
[<c0272c38>] (mutex_lock_nested+0x24/0x35c) from [<c01b237c>]
(mdiobus_read+0x44/0x70)
[<c01b237c>] (mdiobus_read+0x44/0x70) from [<c01b0c64>]
(phy_mii_ioctl+0x4c/0x138)
[<c01b0c64>] (phy_mii_ioctl+0x4c/0x138) from [<c01b34fc>]
(stmmac_ioctl+0x5c/0x78)
[<c01b34fc>] (stmmac_ioctl+0x5c/0x78) from [<c01fcec8>]
(dev_ifsioc+0x2a4/0x2c8)
[<c01fcec8>] (dev_ifsioc+0x2a4/0x2c8) from [<c01fd81c>]
(dev_ioctl+0x560/0x674)
[<c01fd81c>] (dev_ioctl+0x560/0x674) from [<c00c36e0>]
(vfs_ioctl+0x2c/0x8c)
[<c00c36e0>] (vfs_ioctl+0x2c/0x8c) from [<c00c4130>]
(do_vfs_ioctl+0x530/0x578)
[<c00c4130>] (do_vfs_ioctl+0x530/0x578) from [<c00c41ac>]
(sys_ioctl+0x34/0x54)
[<c00c41ac>] (sys_ioctl+0x34/0x54) from [<c0028aa0>]
(ret_fast_syscall+0x0/0x2c)
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

New GMAC devices (newer than the databook 3.50a) have the
HW capability register that provides which features are actually
supported by the hardware.

On old devices many information have to be passed through the
platform, for example: enhanced descriptor structure,
TX COE etc. These are mandatory to properly configure the driver.
This remains still valid because the driver has to support old
Synopsys devices but now it's also able to override them using the
values from the HW capability register if supported.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes the way to stop the 1000Base advertising
capabilties for non GMII interfaces.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch uses an mdelay to manage the timeout on
sw reset to be independant of cpu_clk.
Signed-off-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Update version number.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Rather than generating a different RSS key on each boot, just use
a predetermined value that will map same flow to same value on
every device.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The default Tx ring size for the sky2 driver is quite large and could
cause excess buffer bloat for many users. The minimum ring size
possible and still allow handling  the worst case packet on 64bit platforms
is 38 which gets rounded up to a power of 2. But most packets only require
a couple of ring elements.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The code is clearer if the up/down functions are renamed to
open/close like other drivers.  Purely syntax change.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

A couple of the reset and setup paths have possible PCI posting issues.
When setting registers, a read is necessary to force the writes to complete.
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

There are several problems with recent change to how IRQ's are setup.
   * synchronize_irq in sky2_shutdown would hang because there
     was no IRQ setup.
   * when device was set to down, some IRQ bits left enabled so a
     hardware error would produce IRQ with no handler
   * quick link on Optima chip set was enabled without handler
   * suspend/resume would leave IRQ on with no handler if device
     was down
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

We are checking whether the MCR0_HASHEN bit is set using a logical and
instead of bitwise and, fix that.
Signed-off-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The first #include must be pch_gbe.h as it
does a #define of pr_fmt.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Re-request fw from fs may fail for different reasons, once the fw was
loaded we won't release it until driver is removed.

This also resolves the boot problem when initial fw is located on initrd,
but rootfs is still unavailable, in this case device reset will fail due
to absence of fw files.
Signed-off-by: NDmitry Kravkov <dmitry@broadcom.com>
Signed-off-by: NEilon Greenstein <eilong@broadcom.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

so the defconfig of the atmel continue to have the support of the network
as before
Signed-off-by: NJean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Only update VERSION to reflect previous changes.
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Now works on Samsung Series 5 (chromebook)

Two fixes here:
o use 0x7F mask for phymode
o read phyid *AFTER* phy is powered up (via GPIOs)
Signed-off-by: NAllan Chou <allan@asix.com.tw>
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

ax88772_reset takes about 2 seconds and is called twice.
Once from ax88772_bind() directly and again indirectly from usbnet_open().
Reset the USB FW/Phy enough to blink the LEDs when inserted.
Signed-off-by: NAllan Chou <allan@asix.com.tw>
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Sometimes the phy isn't ready after reset...poll and pray it will be soon.
Signed-off-by: NFreddy Xin <freddy@asix.com.tw>
Signed-off-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Use correct value for rtl phy support.
(rtl phy are in AX88178 devices like NWU220G and USB2-ET1000).
Signed-off-by: NAllan Chou <allan@asix.com.tw>
Tested-by: NGrant Grundler <grundler@chromium.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we hit the default case in the switch in if_spi_host_to_card() we'll leak
the memory we allocated for 'packet'. This patch resolves the leak by freeing
the allocated memory in that case.
Signed-off-by: NJesper Juhl <jj@chaosbits.net>
Acked-by: NDan Williams <dcbw@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The generic powersaving code that determines after reception of a frame
whether the device should go back to sleep or whether is could stay
awake was calling rt2x00lib_config directly from RX tasklet context.
On a number of the devices this call can actually sleep, due to having
to confirm that the sleeping commands have been executed successfully.

Fix this by moving the call to rt2x00lib_config to a workqueue call.

This fixes bug https://bugzilla.redhat.com/show_bug.cgi?id=731672Tested-by: NTomas Trnka <tomastrnka@gmx.com>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Cc: <stable@vger.kernel.org>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This is reported to be an RT3070 based device.
Reported-by: NTeika Kazura <teika@lavabit.com>
Signed-off-by: NGertjan van Wingerde <gwingerde@gmail.com>
Acked-by: NIvo van Doorn <IvDoorn@gmail.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

The Lantiq ETOP ethernet driver fails to build in 3.2-rc1 due to 2 missing
header files.
Signed-off-by: NJohn Crispin <blogic@openwrt.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When HW doesn't remove FCS bytes they are reported in the completion
byte count, we don't need to take them to skb.
Signed-off-by: NYevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Add checking for valid magic values (needed for stability in the event
corrupted packets are received) and remove some other unneeded checks.
Also, fix flagging device as WWAN (Bugzilla bug #39952).
Signed-off-by: NMark Kamichoff <prox@prolixium.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>