To stop an out endpoint, software should set sets the Global OUT NAK,
but not the Global Non-periodic IN NAK. This driver bug leads the out-ep
failed be in disabled state with below error.

dwc2_hsotg_ep_stop_xfr: timeout DOEPCTL.EPDisable
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NDu, Changbin <changbin.du@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It dose not work when we want to use the usb-to-serial port based
on one usb gadget as a console. Thus this patch adds the console
initialization to support this request.

To avoid the re-entrance when transferring data with usb endpoint,
it introduces a kthread to do the IO transmission.
Signed-off-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If OF is disabled, we will try to define a stub for
of_usb_get_dr_mode_by_phy(), however that missed a
static inline annotation which made us redefine the
stub over and over again. Fix that.

Fixes: 98bfb394 ("usb: of: add an api to get
	dr_mode by the phy node")
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Fix bad unlock balance: ep0_write enter with the locks locked from
inode.c:1769, hence it must exit with spinlock held to avoid double
unlock in dev_config.
Signed-off-by: NDavid Eccher <d.eccher@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Simply document new compatibility string.
As a previous patch adds a generic R-Car Gen2 compatibility string
there appears to be no need for a driver updates.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Add fallback compatibility strings for R-Car Gen2 and Gen3.
This is in keeping with the fallback scheme being adopted wherever
appropriate for drivers for Renesas SoCs.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This extends the documentation of compatibility strings a little to
include the SoC names.
Signed-off-by: NSimon Horman <horms+renesas@verge.net.au>
Acked-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The gadget ethernet driver supports changing the MTU, but only allows this
when the USB cable is removed. The comment indicates that this is because
the "peer won't know". Even if the network link is still down and only the
USB link is established, the driver won't allow the change.

Other network interfaces allow changing the MTU any time, and don't force
the link to be disabled. This makes perfect sense, because in order to be
able to negotiate the MTU, the link needs to be up.

Remove the restriction so that it is now actually possible to change the
MTU (e.g. using "ifconfig usb0 mtu 15000") without having to manually pull
the plug or change the driver's default setting.

This is especially important after commit bba787a8
("usb: gadget: ether: Allow jumbo frames")
Signed-off-by: NMike Looijmans <mike.looijmans@topic.nl>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

It seems that gitorious repository is no longer accessible, so we
replace it with address to active repository.
Signed-off-by: NRobert Baldyga <r.baldyga@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch introduces pre-allocation of IN endpoint USB requests. This
improves on latency (requires no usb request allocation on transmit) and avoid
several potential probles on allocating too many usb requests (which involves
DMA pool allocation problems).

This implementation also handles better multiple MIDI Gadget ports, always
processing the last processed MIDI substream if the last USB request wasn't
enought to handle the whole stream.
Signed-off-by: NFelipe F. Tonello <eu@felipetonello.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This ensures that the midi function will only work if the proper number of
IN and OUT requrests are allocated. Otherwise the function will work with less
requests then what the user wants.
Signed-off-by: NFelipe F. Tonello <eu@felipetonello.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This avoids duplication of USB requests for OUT endpoint and
re-enabling endpoints.
Signed-off-by: NFelipe F. Tonello <eu@felipetonello.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

When reloading omap2430 kernel module we get a warning about
unbalanced pm_runtime_enable. Let's fix this. Note that we
need to do this after the child musb-core platform_device is
removed because of pm_runtime_irq_safe being set at the child.

Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

We currently can't unload omap2430 MUSB platform glue driver module and
this cause issues for fixing the MUSB code further. The reason we can't
remove omap2430 is because it uses the PHY functions and also exports the
omap_musb_mailbox function that some PHY drivers are using.

Let's fix the issue by exporting a more generic musb_mailbox function
from the MUSB core and allow platform glue layers to register phy_callback
function as needed.

And now we can now also get rid of the include/linux/musb-omap.h.

Cc: Bin Liu <b-liu@ti.com>
Cc: Felipe Balbi <balbi@ti.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: NeilBrown <neil@brown.name>
Reviewed-by: NKishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch removes redundant condition.

 (!A || (A && B)) is the same as (!A || B).

Fixes indentation too.

Tested by: compilation only
Caught by: cppcheck
Signed-off-by: NGeyslan G. Bem <geyslan@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This patch removes redundant condition.

 (!A || (A && B)) is the same as (!A || B).

Tested by compilation only.
Caught by cppcheck.
Signed-off-by: NGeyslan G. Bem <geyslan@gmail.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

instead of using:

	if (condition) {
		dev_WARN_ONCE(dev, true, "foo");
		return -EINVAL;
	}

let's use:

	if (dev_WARN_ONCE(dev, condition, "foo"))
		return -EINVAL;
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Change behavior during registration of gadgets and
gadget drivers in udc-core. Instead of previous
approach when for successful probe of usb gadget driver
at least one usb gadget should be already registered
use another one where gadget drivers and gadgets
can be registered in udc-core independently.

Independent registration of gadgets and gadget drivers
is useful for built-in into kernel gadget and gadget
driver case - because it's possible that gadget is
really probed only on late_init stage (due to deferred
probe) whereas gadget driver's probe is silently failed
on module_init stage due to no any UDC added.

Also it is useful for modules case - now there is no
difference what module to insert first: gadget module
or gadget driver one.
Tested-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NRuslan Bilovol <ruslan.bilovol@gmail.com>
[simplified code as requested by Alan Stern and Felipe Balbi,
 fixed checkpatch issues]
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Now when last user of usb_udc_attach_driver() is switched
to passing UDC name via usb_gadget_driver struct, it's safe
to remove this function
Tested-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NRuslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Now when udc-core supports binding to specific UDC by passing
its name via 'udc_name' member of usb_gadget_driver struct,
switch to this generic approach.
Tested-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NRuslan Bilovol <ruslan.bilovol@gmail.com>
[rebased and fixed checkpatch issues]
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Introduce new 'udc_name' member to usb_gadget_driver structure.
The 'udc_name' is a name of UDC that usb_gadget_driver should
be bound to. If udc_name is NULL, it will be bound to any
available UDC.
Tested-by: NMaxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: NRuslan Bilovol <ruslan.bilovol@gmail.com>
Signed-off-by: NMarek Szyprowski <m.szyprowski@samsung.com>
Tested-by: NPeter Chen <peter.chen@freescale.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

To prevent VBUS contention, the am335x MUSB phy senses VBUS first before
transitioning to host mode. However, for host-only mode, VBUS could be
directly tied to 5V power rail which could prevent MUSB transitions to
host mode.

This change receives dr_mode of the controller then bypass the first
VBUS sensing for host-only mode, so that MUSB can work in host mode
event if VBUS is tied to 5V.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The filename of am35x-phy-control.h is confusing. The header is used
by the am335x phy driver, but the filename refers to am35x. Even worse
there is indeed another device called am35x but it does not use this
header at all.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As of commit 3d7608e4 ("ARM: shmobile: bockw: remove legacy
board file and config"), the Renesas R-Car (Gen1) USB PHY driver is no
longer used.
In theory it could still be used on R-Car Gen1 SoCs, but that would
require adding DT support to the driver. Instead, a new driver using the
generic PHY framework should be written, as was done for R-Car Gen2.

Remove the driver for good.
Acked-by: NSimon Horman <horms+renesas@verge.net.au>
Signed-off-by: NGeert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Remove mach/irq.h from the list of included headers, there is no
compilation dependency on this include file, and the change is needed
to prevent a compilation failure, when mach/irq.h is removed.

Additionally remove other unneeded includes and sort out their order.
Signed-off-by: NVladimir Zapolskiy <vz@mleia.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

struct usb_request have 3 flags which might be
important to know about during debug. This patch
shows each of the 3 flags as a single letter:

z -> for zero
s -> short not okay
i -> interrupt

A capital letter means the feature is enabled
while a lower case letter means it is disabled;

Thus 'zsI' indicates that a ZLP is not needed,
that we can accept a short packet and interrupt
for this request should be enabled.
Signed-off-by: NFelipe Balbi <balbi@ti.com>

So far, dwc3 has always missed request->zero
handling for every endpoint. Let's implement
that so we can handle cases where transfer must
be finished with a ZLP.

Note that dwc3 is a little special. Even though
we're dealing with a ZLP, we still need a buffer
of wMaxPacketSize bytes; to hide that detail from
every gadget driver, we have a preallocated buffer
of 1024 bytes (biggest bulk size) to use (and
share) among all endpoints.
Reported-by: NRavi B <ravibabu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

This file already uses pr_debug in a few places; this converts the
remaining printks.
Signed-off-by: NRasmus Villemoes <linux@rasmusvillemoes.dk>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In general it is wise to clear interrupts before processing them.  If
you don't do that, you can get:
 1. Interrupt happens
 2. You look at system state and process interrupt
 3. A new interrupt happens
 4. You clear interrupt without processing it.

This patch was actually a first attempt to fix missing device insertions
as described in (usb: dwc2: host: Fix missing device insertions) and it
did solve some of the signal bouncing problems but not all of
them (which is why I submitted the other patch).  Specifically, this
patch itself would sometimes change:
 1. hardware sees connect
 2. hardware sees disconnect
 3. hardware sees connect
 4. dwc2_port_intr() - clears connect interrupt
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

...to:
 1. hardware sees connect
 2. hardware sees disconnect
 3. dwc2_port_intr() - clears connect interrupt
 4. hardware sees connect
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

...but with different timing then sometimes we'd still miss cable
insertions.

In any case, though this patch doesn't fix any (known) problems, it
still seems wise as a general policy to clear interrupt before handling
them.

Note that for dwc2_handle_usb_port_intr(), instead of moving the clear
of PRTINT to the beginning of the function we remove it completely.  The
only way to clear PRTINT is to clear the sources that set it in the
first place.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

The dwc2_hcd_reset_func() function is only ever called directly by a
delayed work function.  As such no locks are already held when the
function is called.

Doing a read-modify-write of CPU registers and setting fields in the
main hsotg data structure is a bad idea without locks.  Let's add
locks.

The bug was found by code inspection only.  It turns out that the
dwc2_hcd_reset_func() is only ever called today if the
"host_support_fs_ls_low_power" parameter is enabled and no code in
mainline enables that parameter.  Thus no known issues in mainline are
fixed by this patch, but it's still probably wise to fix the function.
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Some USB phy drivers have different handling for the controller in each
dr_mode. But the phy driver does not have visibility to the dr_mode of
the controller.

This adds an api to return the dr_mode of the controller which
associates the given phy node.
Signed-off-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since now, we may have more than one request during the test, and
it is better we just quit once the error occurs instead of try
queueing further requests.
Signed-off-by: NPeter Chen <peter.chen@freescale.com>
Suggested-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Reviewed-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Since composite now overwrites bcdUSB for any gadget, remove
setting it in legacy gadgets. All legacy gadgets set 0x0200, the
same as the value additionally set by composite, so there is no
behaviour change.
Signed-off-by: NIgor Kotrasinski <i.kotrasinsk@samsung.com>

Rebase onto current balbi/next
Signed-off-by: NKrzysztof Opasiak <k.opasiak@samsung.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

In some cases, like when you've got a "Microsoft Wireless Keyboard 2000"
connected to dwc2 with a hub, expected that we'll get some transfer
errors sometimes.  The controller is expected to try at least 3 times
before giving up.  See figure "Figure A-67. Normal HS CSPLIT 3 Strikes
Smash" in the USB spec.

The dwc2 controller has a way to support this by using the "EC_MC"
field.  The Raspberry Pi driver has logic for setting this right.  See
fiq_fsm_queue_split_transaction() in their "dwc_otg_hcd.c".  Let's use
the same logic.

After making this change, we no longer get dropped characters from the
above mentioned keyboard.  Other devices on the same bus as the keyboard
also behave more properly.

Thanks for Julius Werner for the expert analysis and suggestions.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

If you've got your interrupt signals bouncing a bit as you insert your
USB device, you might end up in a state when the device is connected but
the driver doesn't know it.

Specifically, the observed order is:
 1. hardware sees connect
 2. hardware sees disconnect
 3. hardware sees connect
 4. dwc2_port_intr() - clears connect interrupt
 5. dwc2_handle_common_intr() - calls dwc2_hcd_disconnect()

Now you'll be stuck with the cable plugged in and no further interrupts
coming in but the driver will think we're disconnected.

We'll fix this by checking for the missing connect interrupt and
re-connecting after the disconnect is posted.  We don't skip the
disconnect because if there is a transitory disconnect we really want to
de-enumerate and re-enumerate.

Notes:
1. As part of this change we add a "force" parameter to
   dwc2_hcd_disconnect() so that when we're unloading the module we
   avoid the new behavior.  The need for this was pointed out by John
   Youn.
2. The bit of code needed at the end of dwc2_hcd_disconnect() is
   exactly the same bit of code from dwc2_port_intr().  To avoid
   duplication, we refactor that code out into a new function
   dwc2_hcd_connect().
Signed-off-by: NDouglas Anderson <dianders@chromium.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Tested-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Support hisilicon,hi6220-usb for HiKey board
Acked-by: NRob Herring <robh@kernel.org>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NZhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Kmem caches help to get correct boundary for descriptor buffers
which need to be 512 bytes aligned for dwc2 controller.
Two kmem caches are needed for generic descriptors and for
hs isochronous descriptors which doesn't have same size.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Masks for HCDMA.CTD and HCDMA.DMAAddr are incorrect. As we always
start from first descriptor, no need to mask the address anyway.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

Use Streaming DMA mappings to handle cache coherency of frame list and
descriptor list. Cache are always flushed before controller access it
or before cpu access it.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>

As descriptor dma mode does not support split transfers, it can't be
enabled for high speed devices. Add a core parameter to enable it for
full speed devices.

Ensure frame list and descriptor list are correctly freed during
disconnect.
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NMian Yousaf Kaukab <yousaf.kaukab@intel.com>
Signed-off-by: NGregory Herrero <gregory.herrero@intel.com>
Signed-off-by: NFelipe Balbi <balbi@ti.com>