Fixes build error on x86_64 allmodconfig, introduced by commit
5ab3a89a ("mfd: syscon: Add non-DT support").

drivers/regulator/anatop-regulator.c: In function 'anatop_regulator_probe':
drivers/regulator/anatop-regulator.c:134:2: error: implicit declaration of function 'of_get_parent' [-Werror=implicit-function-declaration]
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Acked-by: NRob Herring <rob.herring@calxeda.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the newly introduced devm_ioremap_resource() instead of
devm_request_and_ioremap() which provides more consistent error handling.

devm_ioremap_resource() provides its own error messages; so all explicit
error messages can be removed from the failure code paths.
Signed-off-by: NSachin Kamat <sachin.kamat@linaro.org>
Acked-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Ordering so many Kconfig alphabetically makes it a lot easier to read e.g.
from menuconfig.
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Provides support for 1801 variant of stmpe gpio port expanders.
This chip has 18 gpios configurable as GPI, GPO, keypad matrix,
special key or dedicated key function.

Note that special/dedicated key function is not supported yet.
Signed-off-by: NJean-Nicolas Graux <jean-nicolas.graux@stericsson.com>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use the wrapper functions for getting and setting the driver data using
spi_device instead of using dev_{get|set}_drvdata with &spi->dev, so we
can directly pass a struct spi_device.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The registration of the "leds-gpio" device was using
"vexpress_sysreg_dev" as a parent before it was actually
set to something different than NULL.

Trivial fix by reordering the code.
Reported-by: NLorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: NPawel Moll <pawel.moll@arm.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The abx500-clk driver is initiated at arch_initcall level. Moreover it
is relying on the ab8500-sysctrl API to be available. Therefore move
ab8500-sysctrl to arch_initcall level as well. The device is already
added before the abx500 clk device, thus it will be probed before as
well, which is exactly what we want.
Signed-off-by: NUlf Hansson <ulf.hansson@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Currently we check to see if we obtained the Tightly Coupled Program
Memory (TCPM) base and only execute the code within the check if we
have it. It's more traditional to return early if we don't have it.
This way we can flatten most of the function's code down to a single
tab spacing.
Signed-off-by: NLee Jones <lee.jones@linaro.org>
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

syscon.h header uses struct device_node in functions' declarations
without declaring it. This causes compilation warnings like:

include/linux/mfd/syscon.h:20: warning: ‘struct device_node’
declared inside parameter list
include/linux/mfd/syscon.h:20: warning: its scope is only this
definition or declaration, which is probably not what you want

Fix it by adding a forward declaration of struct device_node.
Signed-off-by: NSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: NKyungmin Park <kyungmin.park@samsung.com>
Acked-by: NDong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add of_comptabile string to the ab8500-usb cell to allow the driver to
grab properties from device-tree when available.
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Allows the OMAP HS USB host controller to be specified
via device tree.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Reviewed-by: NMark Rutland <mark.rutland@arm.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

PHY reset GPIO handling will be done in the PHY driver
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

For realistic systems the power management is controlled entirely via
runtime PM - if the device is not runtime suspended then the suspend
will abort without doing anything as functionality such as accessory
detection or audio bypass will require the device to be enabled while
if the device is runtime suspended it is already in the lowest power
state. This means that system suspend is redundant and can be removed
which avoids issues with attempting to double disable the regulators.
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

AB8500 asserts LATCH bits for masked out interrupts.  This patch
explicitly masks those out using the cached mask value to prevent
handle_nested_irq() being called for masked IRQ on the same register as
unmasked ones.
Acked-by: NLinus Walleij <linus.walleij@linaro.org>
Signed-off-by: NFabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Twelve Kconfig symbols, all related to WM8350, WM8351, and WM8352, are
unused. Commit 19d57ed5 ("mfd: Remove
custom wm8350 cache implementation") removed all their (actual) users.
Remove these symbols too.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Acked-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: NKukjin Kim <kgene.kim@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This patch changes the irq state from high to the now default low.
Because the default PMIC irq state of DA9055 got changed from high to low.
This change should not affect any of the existing users since all of them
use active low state.

This patch has been tested on smdkv6410.
Signed-off-by: NAshish <ashish.jangam@kpitcummins.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Allows the OMAP USB TLL module to be specified via device tree.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This is because we want to get rid of platform_data usage from probe().
The only information we need is PORT_MODE, and this can be supplied
to us by the user (i.e. omap-usb-host.c).

We also move channel clock management from runtime PM handlers into
omap_tll_enable/disable().
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

EHCI driver would need to know the number of ports available
on the platform. We set the nports parameter of platform_data
based on IP version if it was not already provided.
Signed-off-by: NRoger Quadros <rogerq@ti.com>
Acked-by: NFelipe Balbi <balbi@ti.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The Kconfig entry for DA9055 PMIC Support selects PMIC_DA9055. That was
probably inspired by the similar select statement in the entry for
DA9052/53 PMIC with I2C. But the DA9055 PMIC only comes in an I2C
variant and its driver doesn't need a separate Kconfig symbol for shared
code. In any case, this select can be dropped as PMIC_DA9055 doesn't
exist.
Signed-off-by: NPaul Bolle <pebolle@tiscali.nl>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Palmas device have three different i2c addresses. The device creates
the two new dummy i2c clients for accessing the register by using
primary client adapter. This new dummy i2c client have their of_node
as NULL.

The dummy i2c client is used for registering interrupt and on this,
it creates irq domain handle. This created irq domain handle has
their of_node as NULL.

Now when any child of this device is registered through the DT as
follows:
         palmas: tps65913@58 {
         	::::::::::::::::::

         	#interrupt-cells = <2>;
                interrupt-controller;

                palmas_rtc {
                       compatible = "ti,palmas-rtc";
                       interrupt-parent = <&palmas>;
                       interrupts = <8 0>;
                };
                ::::::::::;;;
         };

And child driver (palam-rtc in this case) get their irq number as
	irq = platform_get_irq(pdev, 0);

The returned irq number is error in this case. The reason is that
the created irq_domain handle for the palmas interrupt does not have
valid node and so matching of node fails with palmas node.

Hence initialising the newly dummy created client->of_node with the
primary clients of_node so that irq_domain handle have proper of_node
for matching.
Signed-off-by: NLaxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Add irq resources to pass to the charger mfd sub dev so
the charger can listen for interrupts.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

The enum is missing the definition for the first bit, which makes all
the rest off by one. Add definition for the TPS65090_IRQ_INTERRUPT bit
which at 0.
Signed-off-by: NRhyland Klein <rklein@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

is_palmas_charger checks for the presence of charging
functionality in the device
Signed-off-by: NGraeme Gregory <gg@slimlogic.co.uk>
Signed-off-by: NIan Lartey <ian@slimlogic.co.uk>
Acked-by: NLaxman Dewangani <ldewangan@nvidia.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

This driver cannot be a module, so "remove" is never called.  The
mishap is mine, and back then there was no warning due to __devexit().
Signed-off-by: NAlessandro Rubini <rubini@gnudd.com>
Acked-by: NGiancarlo Asnaghi <giancarlo.asnaghi@st.com>
Acked-by: NDavide Ciminaghi <ciminaghi@gnudd.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_*() functions to make cleanup paths more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_gpio_request_one() to make cleanup paths more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>

Use devm_gpio_request_one() to make cleanup paths more simple.
Signed-off-by: NJingoo Han <jg1.han@samsung.com>
Signed-off-by: NSamuel Ortiz <sameo@linux.intel.com>