CONFIG_EP93XX_ETH=y, CONFIG_MII=n results in an obvious link error.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add multicast capability to Atmel ethernet macb driver.
Signed-off-by: NPatrice Vilchez <patrice.vilchez@rfo.atmel.com>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Convert the macb driver to use the generic PHY layer in
drivers/net/phy.
Signed-off-by: NFrederic RODO <f.rodo@til-technologies.fr>
Signed-off-by: NHaavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch adds support for DLPAR memory add to the eHEA driver. To detect
whether memory was added the driver uses its own memory mapping table and
checks for kernel addresses whether they're located in already known memory
sections. If not the function ehea_rereg_mrs() is triggered which performs
a rebuild of the mapping table and a re-registration of the global memory
region.
Signed-off-by: NThomas Klein <tklein@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes a potential null dereference bug where we dereference
nic before a null check. This patch simply moves the dereferencing
after the null check.

Signed-off-by: Micah Gruber < micah.gruber@gmail.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Cc: Chad Tindel <ctindel@users.sourceforge.net>
Cc: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Use list_for_each_entry() instead of manual iteration and substitute a
list_for_each_safe() loop with list_for_each_entry_safe()
Signed-off-by: NMatthias Kaehlcke <matthias.kaehlcke@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Acked-by: NLuis R. Rodriguez <mcgrof@gmail.com>
Signed-off-by: NAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Found by Guillaume LECERF <glecerf@gmail.com>
Signed-off-by: NDan Williams <dcbw@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch removes dead code introduced by
commit 90a42210 and spotted
by the Coverity checker.
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

While playing with the firmware a while back, I discovered a way to
access the device's entire address space before the firmware has been
loaded.

Previously we were loading the firmware early on (during probe) so that
we could read the MAC address from the EEPROM and register a netdevice.
Now that we can read the EEPROM without having firmware, we can defer
firmware loading until later while still reading the MAC address early
on.

This has the advantage that zd1211rw can now be built into the kernel --
previously if this was the case, zd1211rw would be loaded before the
filesystem is available and firmware loading would fail.

Firmware load and other device initialization operations now happen the
first time the interface is brought up.

Some architectural changes were needed: handling of the is_zd1211b flag
was moved into the zd_usb structure, MAC address handling was obviously
changed, and a preinit_hw stage was added (the order is now: init,
preinit_hw, init_hw).
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Tested by Zen Kato
zd1211b chip 0411:00da v4810 high 00-16-01 AL2230S_RF pa0 g--N-
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Zen Kato has a device which reports the 0xa RF type. The vendor driver
treats this as AL2230S, the same as devices with the AL2230S bit in the POD.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Zen Kato's device has a regulatory domain value of 0x49, which is not an
IEEE 802.11 code and is not even identified in the vendor driver.

Recent versions of the vendor driver don't even look at the regdomain
value any more, and just allow channels 1-11 everywhere. This patch
brings us more in line with that behaviour, by allowing channels 1-11
for regdomains which we don't know about.
Signed-off-by: NDaniel Drake <dsd@gentoo.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Hi,

This is the third submission of the network driver for PS3.
The differences from the previous one are:

  - renamed source file names so that their prefix can match
    with the module name
  - added cbe-oss-dev@ozlabs.org line for MAINTAINER file
  - changed some in copyright comments

If there are no more comments, please apply for 2.6.23.

Thank you

--
Subject: PS3: Ethernet driver

From: Masakazu Mokuno <mokuno@sm.sony.co.jp>

Add Gigabit Ethernet support for the PS3 game console.  The module will
be called ps3_gelic.

CC: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: NMasakazu Mokuno <mokuno@sm.sony.co.jp>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Don't turn the radio on until the interface is up. This saves some power in
case the driver is loaded but the card is not used.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Callers of enable_MAC() shouldn't have to worry about the bits in the
response's status word (and most of them don't). The return value is
sufficient information.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Matteo Croce reported Aironet initialization failures. They were caused by
a race in airo. airo finds a free interface name, then initializes the card
and finally registers the interface. Another device may get the same name
in the meantime.
The reason airo gets its name early is to use it in informative printks and
to name the resources it requests. The printks will be just fine without
the interface name and the resources can use the driver's name - that's
what other network drivers do anyway.
One of the talkative functions is setup_card(). It is called once before
registration and can be called later again. Let's have an empty dev->name
during the first call, so it doesn't print the ugly "airo(eth%d)" message.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

airo's kernel thread and the IRQ handler are needed only when the interface
is up.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Fix an assymetry between pci_{enable,disable}_device. airo did not disable
the PCI device when unloading the module. This caused suspend failures
after modprobe -r airo && modprobe airo.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

It needs writesb(), not available on all platforms.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Similar patch to ipw2200. Round the timer used for RF kill
switch off to 1 second boundary to save power.
Build tested only, don't have this hardware.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Make the ipw2200 driver polling of rf kill switch occur on second boundaries to reduce
power. Making all the wakeup's in the system occur together reduces power, and keeps
CPU in idle longer.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

I failed to notice that a u16 was being passed to the hardware.
This fixes it.

Thanks to Kasper F. Brandt for finding this!
Signed-off-by: NMichael Wu <flamingice@sourmilk.net>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

... by removing an ill-conceived, useless line.  Discovered by coverity.
Signed-off-by: NHolger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

Remove a header file that was ostensibly "removed" before, in commit
3ce40232.
Signed-off-by: NRobert P. J. Day <rpjday@mindspring.com>
Signed-off-by: NJohn W. Linville <linville@tuxdriver.com>

This patch introduces a capability flag that is used by the DLPAR userspace
tool to check which DLPAR features are supported by the eHEA driver.

Missing goto has been included.
Signed-off-by: NJan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Unmaintained, superceded by skge.

Prodded to deletion by Adrian Bunk.  Acked by Stephen Hemminger.
Signed-off-by: NJeff Garzik <jeff@garzik.org>

This patch fixes the following section mismatch:

<--  snip  -->

...
  MODPOST vmlinux
WARNING: drivers/built-in.o(.text+0x272f8b): Section mismatch: reference to .init.text:quattro_pci_find (between 'happy_meal_pci_probe' and 'happy_meal_pci_remove')
...

<--  snip  -->
Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

	At present, when a device is enslaved to bonding, if ipv6 is
active then addrconf will be initated on the slave (because it is closed
then opened during the enslavement processing).  This causes DAD and RS
packets to be sent from the slave.  These packets in turn can confuse
switches that perform ipv6 snooping, causing them to incorrectly update
their forwarding tables (if, e.g., the slave being added is an inactve
backup that won't be used right away) and direct traffic away from the
active slave to a backup slave (where the incoming packets will be
dropped).

	This patch alters the behavior so that addrconf will only run on
the master device itself.  I believe this is logically correct, as it
prevents slaves from having an IPv6 identity independent from the
master.  This is consistent with the IPv4 behavior for bonding.

	This is accomplished by (a) having bonding set IFF_SLAVE sooner
in the enslavement processing than currently occurs (before open, not
after), and (b) having ipv6 addrconf ignore UP and CHANGE events on
slave devices.

	The eql driver also uses the IFF_SLAVE flag.  I inspected eql,
and I believe this change is reasonable for its usage of IFF_SLAVE, but
I did not test it.
Signed-off-by: NJay Vosburgh <fubar@us.ibm.com>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NAlexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Code will do local_irq_save() on it.
Signed-off-by: NAlexey Dobriyan <adobriyan@sw.ru>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

usbnet_probe() handles a positive return value from the driver bind()
function as success, but will later only setup the status handler if the
return value was zero, leading to confusion. Patch adjusts this to accept
positive values as success in both checks.
Signed-off-by: NPeter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Get rid of dubious casts to (void *) which causes a sparse warning.
And move largeish function from inline to the one file that uses the code,
the compiler can then decide to inline it.

Compile tested only.
Signed-off-by: NStephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Add 88E1112 PHY ID to the marvell driver. Seems to do fine with the
88E1111 inits.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Simplify the marvell driver init a bit: Make the supported devices an
array instead of explicitly registering each structure. This makes it
considerably easier to add new devices down the road.
Signed-off-by: NOlof Johansson <olof@lixom.net>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Support for the Asix AX88796 network controller, an
NE2000 compatible 10/100 ethernet device with internal
PHY.

The driver supports PHY settings via either ioctl() or
the ethtool driver ops.
Signed-off-by: NBen Dooks <ben-linux@fluff.org>
Signed-off-by: NJeff Garzik <jeff@garzik.org>

Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

TX49XX SoCs include PCI NIC (TC35815 compatible) connected via its
internal PCI bus, but the NIC's PROM interface is not connected to
SEEPROM.  So we must provide its ethernet address by another way.
Signed-off-by: NAtsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: NJeff Garzik <jeff@garzik.org>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NAdrian Bunk <bunk@stusta.de>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

Signed-off-by: NFranck Bui-Huu <fbuihuu@gmail.com>
Signed-off-by: NRalf Baechle <ralf@linux-mips.org>

 delete mode 100644 arch/mips/configs/ocelot_c_defconfig
 delete mode 100644 arch/mips/momentum/ocelot_c/Makefile
 delete mode 100644 arch/mips/momentum/ocelot_c/cpci-irq.c
 delete mode 100644 arch/mips/momentum/ocelot_c/dbg_io.c
 delete mode 100644 arch/mips/momentum/ocelot_c/irq.c
 delete mode 100644 arch/mips/momentum/ocelot_c/ocelot_c_fpga.h
 delete mode 100644 arch/mips/momentum/ocelot_c/platform.c
 delete mode 100644 arch/mips/momentum/ocelot_c/prom.c
 delete mode 100644 arch/mips/momentum/ocelot_c/reset.c
 delete mode 100644 arch/mips/momentum/ocelot_c/setup.c
 delete mode 100644 arch/mips/momentum/ocelot_c/uart-irq.c
 delete mode 100644 arch/mips/pci/fixup-ocelot-c.c
 delete mode 100644 arch/mips/pci/pci-ocelot-c.c