Move the gadget devicetree settings into the core_params structure and
document them. Then set and check them in params.c, with the addition of
some helper functions, and remove the equivalent code in gadget.c.

Because these parameters came from the standalone s3c driver, they have
a fixed default value rather than an autodetected one. Preserve and
document this behavior to avoid any compatibility issues.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This hardware parameter is not host specific. It also applies to device
mode. Drop the "host" from the name to make that clear.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Remove the unnecessary prototypes for all the parameter setting
functions and declare those functions 'static' in the params.c file.

Also remove the duplicate documentation that went along with them. They
are already documented as part of the params structure definition.

Then move the constants that went along with the prototype into the
structure.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Replace this by statically defining a function with defaults, and just
assigning it. This will allow us to use parameters of any type and any
default value.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Consolidate and move all the parameter initialization code from the
probe function to params.c.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This makes it consistent with the hw_params struct and simplifies the
memory management for future refactoring. Fix up usage in all files.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add a params.c file and move all driver parameter code there, including
all the static parameter definitions.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The dma_desc_fs_enable does not correspond to any hardware parameter and
is unused. Remove it.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This shouldn't be freed by the HCD as it is owned by the core and
allocated with devm_kzalloc.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Make sure to drop the references taken by of_parse_phandle() and
bus_find_device() before returning from am335x_get_phy_control().

Note that there is no guarantee that the devres-managed struct
phy_control will be valid for the lifetime of the sibling phy device
regardless of this change.

Fixes: 3bb869c8 ("usb: phy: Add AM335x PHY driver")
Acked-by: NBin Liu <b-liu@ti.com>
Signed-off-by: NJohan Hovold <johan@kernel.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The current error handling flow uses incorrect goto label, fix it

Cc: <stable@vger.kernel.org>
Fixes: d12a8727 ("usb: gadget: function: Remove
	redundant usb_free_all_descriptors")
Signed-off-by: NPeter Chen <peter.chen@nxp.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Add super speed descriptors to f_hid.
Signed-off-by: NJanusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The patch improves readability of mv_u3d_start_queue()
by rearranging its code with two semantic modifications:
- assignment zero to ep->processing if usb_gadget_map_request() fails;
- propagation of error code from mv_u3d_req_to_trb() instead of
  hardcoded -ENOMEM.
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

mv_u3d_req_to_trb() does not check for dma mapping errors.

Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: NAlexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Finally get rid of dwc3_trace() hack. If any other
message is truly needed, we should add proper
tracepoints for them instead of hacking around with
dwc3_trace() or similar.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

instead of using a simple trace_printk() wrapper,
let's add an actual tracepoint and print further
details about the endpoint being operated upon.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Intel's BXT devices need to execute a _DSM method
during {runtime_,}{suspend,resume} in order to get a
chunk of dwc3 to power gate and save some extra
power.

Let's do that now.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

We'll be tracking a little more information for PCI
drivers, it's about time we add a private structure
for that.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When we get a half-way processed request, we should
make sure to try to prepare further TRBs for it or
for any possibly queued up request held in our
pending_list. This will make sure our controller is
kept busy for as long as possible.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Say we have three requests prepared to the HW (reqA,
reqB, and reqC). All of them are composed of
SG-lists with several entries and they all requests
interrupt only on last TRBs of the SG-list.

When we get interrupt for reqA, it could be that
reqB is already half-way transferred and some of its
TRBs will have HWO already cleared.

It's okay to free up TRBs without HWO bit set, but
we need to guarantee we don't giveback a request
that's half-way transferred as that will confuse
gadget drivers.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

In cases where we're given an SG-list which is
longer than the amount of currently available TRBs,
we will be left with the same request on
started_list and we should prioritize that request
over possible new requests on pending_list. That's
a way to guarantee requests complete in order.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This will give us a simpler way of figuring out how
many bytes were left in each TRB. It's useful for
cases where we queue only part of an SG-list due to
amount of available TRBs at the time of kicking the
transfer.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

If XferNotReady comes before usb_ep_queue() we will
set our PENDING request flag and wait for a
request. However, originally, we were assuming
usb_ep_queue() would always happen before our first
XferNotReady and that causes a corner case where we
could try to issue ENDTRANSFER command before
STARTTRANSFER.

Let's fix that by tracking endpoints which have been
started.
Reported-by: NJanusz Dziedzic <januszx.dziedzic@intel.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Instead of just delaying for 100us, we should
actually wait for End Transfer Command Complete
interrupt before moving on. Note that this should
only be done if we're dealing with one of the core
revisions that actually require the interrupt before
moving on.

[ felipe.balbi@linux.intel.com: minor improvements ]
Signed-off-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

dev_kfree_skb_any() is used to free packets that are dropped by the
network stack. Therefore the function should not be used for packets
that have been successfully processed by the network stack. Instead
dev_consume_skb_any() has to be used for such consumed packets.

This separation helps to identify dropped packets.
Signed-off-by: NTorsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: NHarish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Socket buffers should be linked to the (network) device that allocated
the buffers. __netdev_alloc_skb performs this task.
Signed-off-by: NTorsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: NJim Baxter <jim_baxter@mentor.com>
Signed-off-by: NHarish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Socket buffers should be linked to the (network) device that allocated
the buffers.
Signed-off-by: NTorsten Polle <tpolle@de.adit-jv.com>
Signed-off-by: NHarish Jenny K N <harish_kandiga@mentor.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

There is only one waiter for the completion, therefore there
is no need to use complete_all(). Let's make that clear by
using complete() instead of complete_all().

The usage pattern of the completion is:

waiter context                          waker context
  reinit_completion()
  usb_esp_queue()
  wait_for_completion_interruptible()

					ffs_ep0_complete()
					  complete()
Acked-by: NMichal Nazarewicz <mina86@mina86.com>
Signed-off-by: NDaniel Wagner <daniel.wagner@bmw-carit.de>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Michal Nazarewicz <mina86@mina86.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Acked-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

The combo of list_empty() check and return list_first_entry()
can be replaced with list_first_entry_or_null().
Signed-off-by: NMasahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Use the more common logging mechanism.

Miscellanea:

o Realign multiline statements
o Coalesce format
Acked-by: NRobert Jarzmik <robert.jarzmik@free.fr>
Acked-by: NNicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Let's not reimplement generic kernel helpers,
instead call kasprintf().

[ felipe.balbi@linux.intel.com: better commit log ]
Signed-off-by: NJuergen Gross <jgross@suse.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

When we change the USB function with configfs dynamically, we possibly
met this situation: one core is doing the control transfer, another core
is trying to unregister the USB gadget from userspace, we must wait for
completing this control tranfer, or it will hang the controller to set
the DEVCTRLHLT flag.

[ felipe.balbi@linux.intel.com: several fixes to the patch
	- call complete() before starting following SETUP transfer
	- add a macro for ep0_in_setup's timeout
	- change commit subject slightly
	- break lines at 72 characters (git adds an 8-character tab)
	- avoid changes to dwc3_gadget_run_stop() ]
Signed-off-by: NBaolin Wang <baolin.wang@linaro.org>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

That function is unnecessarily called from
dwc3_gadget_reset_interrupt(). Gadget drivers (and
thus, functions) are required to dequeue all pending
requests when they get notified about a USB Bus
Reset.

Trying to make sure there are no pending requests
only serves the purpose of working around possibly
bad gadgets.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This helper will be responsible for reading and
parsing our properties. No functional changes in
this patch, cleanup only.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

Kernel will give us page aligned memory anyway.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This little helper will be used to setup anything
related to GCTL register. There are no functional
changes, this is a cleanup only patch.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

This little helper will be used to make sure we're
dealing with a valid Synopsys DWC3 or DWC3.1 core.
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>

For the usb31 IP and from version 2.90a of the usb3 IP, the core
supports HW exit from L1 in HS. Enable it, otherwise the controller may
never exit from LPM to do a transfer.
Signed-off-by: NJohn Youn <johnyoun@synopsys.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@linux.intel.com>