Skip to content

K
Kernel

openeuler / Kernel
12 个月 前同步成功

通知 5
Star 0
Fork 0
K
Kernel

体验新版 GitCode，发现更多精彩内容 >>

切换分支/标签
  1. 07 10月, 2009 15 次提交
  3. 06 10月, 2009 1 次提交
  5. 05 10月, 2009 9 次提交
  7. 03 10月, 2009 12 次提交
  9. 02 10月, 2009 3 次提交
    • A
      net: Use sk_mark for routing lookup in more places · 914a9ab3
      由 Atis Elsts 提交于 
      This patch against v2.6.31 adds support for route lookup using sk_mark in some 
more places. The benefits from this patch are the following.
First, SO_MARK option now has effect on UDP sockets too.
Second, ip_queue_xmit() and inet_sk_rebuild_header() could fail to do routing 
lookup correctly if TCP sockets with SO_MARK were used.
Signed-off-by: NAtis Elsts <atis@mikrotik.com>
Acked-by: NEric Dumazet <eric.dumazet@gmail.com>
      914a9ab3
    • S
      sky2: irqname based on pci address · 66466797
      由 Stephen Hemminger 提交于 
      This is based on Michal Schmidt fix for skge.

Most network drivers request their IRQ when the interface is activated.
sky2 does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:

1. modprobe sky2
   The card is detected as eth0 and requests IRQ 17. Directory
   /proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
   eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
   The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
   Now 8139too requests IRQ 17.

The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered

The fix is for sky2 to name the irq based on the pci device, as is done
by some other devices DRM, infiniband, ...  ie. sky2@pci:0000:00:00
Signed-off-by: NStephen Hemminger <shemminger@vyatta.com>
Reviewed-by: NMichal Schmidt <mschmidt@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      66466797
    • M
      skge: use unique IRQ name · 415e69e6
      由 Michal Schmidt 提交于 
      Most network drivers request their IRQ when the interface is activated.
skge does it in ->probe() instead, because it can work with two-port
cards where the two net_devices use the same IRQ. This works fine most
of the time, except in some situations when the interface gets renamed.
Consider this example:

1. modprobe skge
   The card is detected as eth0 and requests IRQ 17. Directory
   /proc/irq/17/eth0 is created.
2. There is an udev rule which says this interface should be called
   eth1, so udev renames eth0 -> eth1.
3. modprobe 8139too
   The Realtek card is detected as eth0. It will be using IRQ 17 too.
4. ip link set eth0 up
   Now 8139too requests IRQ 17.

The result is:
WARNING: at fs/proc/generic.c:590 proc_register ...
proc_dir_entry '17/eth0' already registered
...
And "ls /proc/irq/17" shows two subdirectories, both called eth0.

Fix it by using a unique name for skge's IRQ, based on the PCI address.
The naming from the example then looks like this:
$ grep skge /proc/interrupts
 17:        169   IO-APIC-fasteoi   skge@pci:0000:00:0a.0, eth0

irqbalance daemon will have to be taught to recognize "skge@" as an
Ethernet interrupt. This will be a one-liner addition in classify.c. I
will send a patch to irqbalance if this change is accepted.
Signed-off-by: NMichal Schmidt <mschmidt@redhat.com>
Acked-by: NStephen Hemminger <shemminger@vyatta.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      415e69e6