Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: David Lv <DavidLv@viatech.com.cn>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Jay Cliburn <jcliburn@gmail.com>
Cc: Chris Snook <chris.snook@gmail.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>
Cc: Andy Gospodarek <andy@greyhouse.net>

Signed-off-by: NFrancois Romieu <romieu@fr.zoreil.com>

Reported-by: NStephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Reported-by: NPaul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The conditional which decides to skip inactive filters does not
change with the change of loop index, so it is unnecessary to
check them many times.
Signed-off-by: NRongQing.Li <roy.qing.li@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since commit 3e4d3af5 (mm: stack based kmap_atomic()) we dont have
to disable BH anymore while mapping skb frags.

We can remove kmap_skb_frag() / kunmap_skb_frag() helpers and use
kmap_atomic() / kunmap_atomic()
Signed-off-by: NEric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is using the DCB netlink to set rate limit per ETS TC
Values are accepted in Kbps and rounded up to the nearest multiply of 100Mbps.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Although not specified in 8021Qaz spec, it could be useful to enable drivers
whose HW supports setting a rate limit for an ETS TC. This patch adds this
optional attribute to DCB netlink. To use it, drivers should implement and
register the callbacks ieee_setmaxrate and ieee_getmaxrate. The units are 64
bits long and specified in Kbps to enable usage over both slow and very fast
networks.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both tagged traffic and untagged traffic use tc tool mapping.
Treat RDMA TOS same as IP TOS when mapping to SL
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
CC: Sean Hefty <sean.hefty@intel.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Need to export this to enable drivers use rt_tos2priority()
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since vlan egress map is only good for tagged traffic, need to have other
mapping to be used by untagged traffic.
For that, the driver uses sch_mqprio mapping. This mapping could be set by
using tc tool from iproute2 package.
Mapped UP will be used by the HW for QoS purposes, but won't go out on the
wire.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Set TSA, promised BW and PFC using IEEE 802.1qaz netlink commands.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Adding QoS firmware commands:
- mlx4_en_SET_PORT_PRIO2TC - set UP <=> TC
- mlx4_en_SET_PORT_SCHEDULER - set promised BW, max BW and PG number
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of relying on HW to change schedule queue by UP, schedule
queue is fixed for a tx_ring, and UP in WQE is ignored in this aspect.  This
resolves two issues with untagged traffic:
1. untagged traffic has no UP in packet which is needed for QoS. The change
   above allows setting the schedule queue (and by that the UP) of such a stream.
2. BlueFlame uses the same field used by vlan tag. So forcing UP from QPC
   allows using BF for untagged but prioritized traffic.

In old firmware that force UP is not supported, untagged traffic will not subject to
QoS.

Because UP is set by QP, need to always have a tx ring per UP, even if pfcrx
module paramter is false.
Signed-off-by: NAmir Vadai <amirv@mellanox.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The R8A7740 has a Gigabit Ethernet MAC. This patch supports it.
Signed-off-by: NYoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: NKuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on original driver from chip manufacturer, but nearly full rewite.
Tested and used in production with Blackfin BF531 embedded processor.
Signed-off-by: NMike Sinkovsky <msink@permonline.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Based on original driver from chip manufacturer, but nearly full rewite.
Tested and used in production with Blackfin BF531 embedded processor.
Signed-off-by: NMike Sinkovsky <msink@permonline.ru>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Convert the macro to inline function to check the arguments.
Signed-off-by: NJoe Perches <joe@perches.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch introduces new team mode. It's TX port is selected by
user-set BPF hash function.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For transfering generic binary data (e.g. BPF code), introduce new
binary option type.
Signed-off-by: NJiri Pirko <jpirko@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If a specific clk_csr value is passed from the platform
this means that the CSR Clock Range selection cannot be
changed at run-time and it is fixed (as reported in the driver
documentation). Viceversa the driver will try to set the MDC
clock dynamically according to the actual clock input.
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Reviewed-by: NDavid Laight <david.laight@aculab.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The CSR Clock Range has been reworked and new macros has
been added in the platform header to allow the CSR Clock
Range selection in the GMII Address Register.
The previous work didn't add the other fields
that can be used to achieve MDC clock of frequency
higher than the IEEE 802.3 specified frequency limit
of 2.5 MHz and program a clock divider of lower value.
On such platforms, these are used indeed so this patch
adds them.
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

this patch adds the way to enable/disable the MAC
clock when call the open/close and resume/restore
functions.
This has been tested on ST platforms and SPEAr; thanks
to Francesco and Deepak.
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Tested-by: NFrancesco Virlinzi <francesco.virlinzi@st.com>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes the infinite waits from the mdio read and
write interfaces. These infinite waits have been replaced by
the timeout handling. In case if a time out occurs, an error is
returned.
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch re-works the internal GMAC DMA parameters
passed from the platform.
In the past, we only passed the pbl but, with new core,
other parameters can be passed and are mandatory on some
platforms.

New parameters are documented in stmmac.txt because this
patch has an impact for many platforms.
Signed-off-by: NShiraz Hashim <shiraz.hashim@st.com>
Signed-off-by: NVikas Manocha <vikas.manocha@st.com>
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Hacked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The patch adds the macros to be used for MDC clock selection. The MDC clock
frequency is based on scaled system clock, and has to be confined to a range
of 1-2.5 MHz. Based on the input CSR clock, the scaling factor has to be
selected.
The platform specific code will provide the default value of this scaling
factor, based on the input CSR clock.
There is an option to set MDC clock higher than the IEEE 802.3 specified
frequency limit of 2.5 MHz. This applies for the interfacing chips that
support higher MDC clocks. The resultant higher clock of 12.5 MHz requires
additional Macros to be defined for the clock divider corresponding to the
to the following selection.
-----------------------------------------
	Selection	MDC Clock
-----------------------------------------
	1000 		clk_csr_i/4
	1001 		clk_csr_i/6
	1010 		clk_csr_i/8
	1011 		clk_csr_i/10
	1100 		clk_csr_i/12
	1101	 	clk_csr_i/14
	1110 		clk_csr_i/16
	1111 		clk_csr_i/18

This support has to be added both in the include file, as well as driver. The
driver need to program the registers based on the interfacing chips. This would
be more board specific information and needs to be passed through the platform
code to the driver. This work would be carried out in the future patch set
release.
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Acked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch sanities the RX coe and adds the Type-1 Rx checksum offload engine (COE).

So the RX COE can be passed through the platform but can be fixed
at run-time in case of the core has the HW capability register.

Also to support the Type-1 Rx COE the driver must append the
HW checksum at the end of payload in case the Rx checksum
engine was used to  offload the HW checksum.

This v2 version also fixes the IPC that has to be enabled and verified.
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Hacked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch explicitly defines the CSUM offload engine type which need
(not mandatory) to be passed from the platform code.
STMMAC core supports two check sum offload engine types- Type-1 & Type-2.
Also, there are STMMAC cores that do not have the check sum offload
capabilities.

The behaviour of Type-1 & Type-2 cores related to provision of checksum
increases the packet length for Type-1 cores by 2, as the checksum is appended
at the end of data packet and the same is made accountable in the DMA status.
The STMMAC cores beyond Version-3.5 provide HW interface registers which allows
the user to read the HW capabilities, while to support the previous cores the
information related to HW capabilities has to be provided from the platform
code.

The Type-1 cores which do not have the HW register interface need this
information.

This patch also updates the driver's doc.
Signed-off-by: NDeepak Sikri <deepak.sikri@st.com>
Hacked-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

As stmmac mdio bus name prefix is hardcoded in the driver, this allows
only phys on stmmac mdio buses to connect, however stmmac should allow
phys on other mdio buses too.

This patch adds new variable phy_bus_name to plat_stmmacenet_data
struct to let the BSP decide which phy bus to be used by stmmac driver.
A typical use-case is to have generic MDIO buses like mdio-gpio on top
of stmmac.
Signed-off-by: NSrinivas Kandagatla <srinivas.kandagatla@st.com>
Acked-by: NFlorian Fainelli <florian@openwrt.org>
Signed-off-by: NGiuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Driver version update
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Renamed following functions:
bnad_cleanup_tx to bnad_destroy_tx
bnad_free_all_txbufs to bnad_txq_cleanup
bnad_free_txbufs to bnad_txcmpl_process
bnad_tx to bnad_tx_complete
bnad_cleanup_rx to bnad_destroy_rx
bnad_reset_rcb to bnad_rcb_cleanup
bnad_free_all_rxbufs to bnad_rxq_cleanup
bnad_cq_cmpl_init to bnad_cq_cleanup
bnad_alloc_n_post_rxbufs to bnad_rxq_post
bnad_poll_cq to bnad_cq_process
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The scheduling of tasklet and keeping the interrupts enabled makes interrupt
reduntant. 20% of the Tx interrupts have nothing left to process or could not
process as Tx tasklet was running.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch removes busy wait in tx/rx cleanup. bnad_cb_tx_cleanup() and
bnad_cb_rx_cleanup() functions are called from irq context, and currently
they do busy wait for the in-flight transmit or the currently executing napi
polling routine to complete. To fix the issue, we create a workqueue to defer
tx & rx cleanup processing, an in the tx rx cleanup handler, we will
wait respective in flight processing to complete, before freeing the buffers.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove irrelevant code. Change to start Hearbeat failure moniter after IOC
become operational.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Added NFC pause/resume logic. We only do NFC pause/resume if NFC version
is greater than 0x143 and it was halted before, otherwise we revert to
old NFC halt mechanism.

Made changes to avoid clearing off the interrupts during the initial
pll initialization.
Signed-off-by: NJing Huang <huangj@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>