There is no need to set the clock speed in read/write which will be performed
unnecessarily for each mdio access. Init it during probe is enough.

Also, the hardcoded clock value is not a proper way for all SoCs.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Which is wrong and not used, so no extra space needed by
mdiobus_alloc_size(), use mdiobus_alloc() instead.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since the reset is just clock setting, individual mdio reset is
not available.
Signed-off-by: NShaohui Xie <Shaohui.Xie@freescale.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Roger Chen says:

====================
support GMAC driver for RK3288

Roger Chen (6):
  patch1: add driver for Rockchip RK3288 SoCs integrated GMAC
  patch2: define clock ID used for GMAC
  patch3: modify CRU config for Rockchip RK3288 SoCs integrated GMAC
  patch4: dts: rockchip: add gmac info for rk3288
  patch5: dts: rockchip: enable gmac on RK3288 evb board
  patch6: add document for Rockchip RK3288 GMAC

Tested on rk3288 evb board:
Execute the following command to enable ethernet,
set local IP and ping a remote host.

busybox ifconfig eth0 up
busybox ifconfig eth0 192.168.1.111
ping 192.168.1.1
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The document descripts how to add properties for GMAC in device tree.

change since v2:

1. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
2. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

enable gmac in rk3288-evb-rk808.dts

changes since v2:
1. add fixed regulator for PHY
2. remove power-gpio, reset-gpio, phyirq-gpio, pmu_regulator setting
3. add "snps,reset-gpio", "snps,reset-active-low;" "snps,reset-delays-us"
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

add gmac info in rk3288.dtsi for GMAC driver

changes since v2:
1. add drive-strength in the pinctrl settings
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

modify CRU config for GMAC driver

changes since v2:
1. remove SCLK_MAC_PLL
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

changes since v2:
1. remove SCLK_MAC_PLL
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This driver is based on stmmac driver.

changes since v2:
- use tab instead of space for macros
- use HIWORD_UPDATE macro for GMAC_CLK_RX_DL_CFG and GMAC_CLK_TX_DL_CFG
- remove drive-strength setting in the driver and set it in the pinctrl settings
- use dev_err instead of pr_err
- remove clock names's macros, just use the real name of the clock
- use devm_clk_get() instead of clk_get()
- remove clk_set_parent(bsp_priv->clk_mac, bsp_priv->clk_mac_pll)
- remove gpio setting for LDO, just use regulator API
- remove phy reset using gpio in the glue layer, it has been handled in the stmmac driver
- remove handling phy interrupt (mii interrupt)

changes since v1:
- use BIT() to set register
- combine two remap_write() operations into one for the same register
- use macros for register value setting
- remove grf fail check in rk_gmac_setup() and save all the check in set_rgmii_speed()
- remove .tx_coe=1 in rk_gmac_data
Signed-off-by: NRoger Chen <roger.chen@rock-chips.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Alexander Duyck says:

====================
fib_trie: Reduce time spent in fib_table_lookup by 35 to 75%

These patches are meant to address several performance issues I have seen
in the fib_trie implementation, and fib_table_lookup specifically.  With
these changes in place I have seen a reduction of up to 35 to 75% for the
total time spent in fib_table_lookup depending on the type of search being
performed.

On a VM running in my Corei7-4930K system with a trie of maximum depth of 7
this resulted in a reduction of over 370ns per packet in the total time to
process packets received from an ixgbe interface and route them to a dummy
interface.  This represents a failed lookup in the local trie followed by
a successful search in the main trie.

				Baseline	Refactor
  ixgbe->dummy routing		1.20Mpps	2.21Mpps
  ------------------------------------------------------------
  processing time per packet		835ns		453ns
  fib_table_lookup		50.1%	418ns	25.0%	113ns
  check_leaf.isra.9		 7.9%	 66ns	   --	 --
  ixgbe_clean_rx_irq		 5.3%	 44ns	 9.8%	 44ns
  ip_route_input_noref		 2.9%	 25ns	 4.6%	 21ns
  pvclock_clocksource_read	 2.6%	 21ns	 4.6%	 21ns
  ip_rcv			 2.6%	 22ns	 4.0%	 18ns

In the simple case of receiving a frame and dropping it before it can reach
the socket layer I saw a reduction of 40ns per packet.  This represents a
trip through the local trie with the correct leaf found with no need for
any backtracing.

				Baseline	Refactor
  ixgbe->local receive		2.65Mpps	2.96Mpps
  ------------------------------------------------------------
  processing time per packet		377ns		337ns
  fib_table_lookup		25.1%	 95ns	25.8%	 87ns
  ixgbe_clean_rx_irq		 8.7%	 33ns	 9.0%	 30ns
  check_leaf.isra.9		 7.2%	 27ns	   --	 --
  ip_rcv			 5.7%	 21ns	 6.5%	 22ns

These changes have resulted in several functions being inlined such as
check_leaf and fib_find_node, but due to the code simplification the
overall size of the code has been reduced.

   text	   data	    bss	    dec	    hex	filename
  16932	    376	     16	  17324	   43ac	net/ipv4/fib_trie.o - before
  15259	    376	      8	  15643	   3d1b	net/ipv4/fib_trie.o - after

Changes since RFC:
  Replaced this_cpu_ptr with correct call to this_cpu_inc in patch 1
  Changed test for leaf_info mismatch to (key ^ n->key) & li->mask_plen in patch 10
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change adds a tracking value for the maximum suffix length of all
prefixes stored in any given tnode.  With this value we can determine if we
need to backtrace or not based on if the suffix is greater than the pos
value.

By doing this we can reduce the CPU overhead for lookups in the local table
as many of the prefixes there are 32b long and have a suffix length of 0
meaning we can immediately backtrace to the root node without needing to
test any of the nodes between it and where we ended up.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For some reason the compiler doesn't seem to understand that when we are in
a loop that runs from tnode_child_length - 1 to 0 we don't expect the value
of tn->bits to change.  As such every call to tnode_get_child was rerunning
tnode_chile_length which ended up consuming quite a bit of space in the
resultant assembly code.

I have gone though and verified that in all cases where tnode_get_child
is used we are either winding though a fixed loop from tnode_child_length -
1 to 0, or are in a fastpath case where we are verifying the value by
either checking for any remaining bits after shifting index by bits and
testing for leaf, or by using tnode_child_length.

size net/ipv4/fib_trie.o
Before:
   text	   data	    bss	    dec	    hex	filename
  15506	    376	      8	  15890	   3e12	net/ipv4/fib_trie.o

After:
   text	   data	    bss	    dec	    hex	filename
  14827	    376	      8	  15211	   3b6b	net/ipv4/fib_trie.o
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change pulls the node_set_parent functionality out of put_child_reorg
and instead leaves that to the function to take care of as well.  By doing
this we can fully construct the new cluster of tnodes and all of the
pointers out of it before we start routing pointers into it.

I am suspecting this will likely fix some concurency issues though I don't
have a good test to show as such.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change pushes the tnode freeing down into the inflate and halve
functions.  It makes more sense here as we have a better grasp of what is
going on and when a given cluster of nodes is ready to be freed.

I believe this may address a bug in the freeing logic as well.  For some
reason if the freelist got to a certain size we would call
synchronize_rcu().  I'm assuming that what they meant to do is call
synchronize_rcu() after they had handed off that much memory via
call_rcu().  As such that is what I have updated the behavior to be.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that the assignment of the tnode to the parent is
handled directly within whatever function is currently handling the node be
it inflate, halve, or resize.  By doing this we can avoid some of the need
to set NULL pointers in the tree while we are resizing the subnodes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change pulls the logic for if we should inflate/halve the nodes out
into separate functions.  It also addresses what I believe is a bug where 1
full node is all that is needed to keep a node from ever being halved.

Simple script to reproduce the issue:
	modprobe dummy;	ifconfig dummy0 up
	for i in `seq 0 255`; do ifconfig dummy0:$i 10.0.${i}.1/24 up; done
	ifconfig dummy0:256 10.0.255.33/16 up
	for i in `seq 0 254`; do ifconfig dummy0:$i down; done

Results from /proc/net/fib_triestat
Before:
	Local:
		Aver depth:     3.00
		Max depth:      4
		Leaves:         17
		Prefixes:       18
		Internal nodes: 11
		  1: 8  2: 2  10: 1
		Pointers: 1048
	Null ptrs: 1021
	Total size: 11  kB
After:
	Local:
		Aver depth:     3.41
		Max depth:      5
		Leaves:         17
		Prefixes:       18
		Internal nodes: 12
		  1: 8  2: 3  3: 1
		Pointers: 36
	Null ptrs: 8
	Total size: 3  kB
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change consists of a cut/paste of resize to behind inflate and halve
so that I could remove the two function prototypes.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change is to start cleaning up some of the rcu_read_lock/unlock
handling.  I realized while reviewing the code there are several spots that
I don't believe are being handled correctly or are masking warnings by
locally calling rcu_read_lock/unlock instead of calling them at the correct
level.

A common example is a call to fib_get_table followed by fib_table_lookup.
The rcu_read_lock/unlock ought to wrap both but there are several spots where
they were not wrapped.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that anything that can be shifted by, or compared
to a value shifted by bits is updated to be an unsigned long.  This is
mostly a precaution against an insanely huge address space that somehow
starts coming close to the 2^32 root node size which would require
something like 1.5 billion addresses.

I chose unsigned long instead of unsigned long long since I do not believe
it is possible to allocate a 32 bit tnode on a 32 bit system as the memory
consumed would be 16GB + 28B which exceeds the addressible space for any
one process.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change moves the pos value to the other side of the "bits" field.  By
doing this it actually simplifies a significant amount of code in the trie.

For example when halving a tree we know that the bit lost exists at
oldnode->pos, and if we inflate the tree the new bit being add is at
tn->pos.  Previously to find those bits you would have to subtract pos and
bits from the keylength or start with a value of (1 << 31) and then shift
that.

There are a number of spots throughout the code that benefit from this.  In
the case of the hot-path searches the main advantage is that we can drop 2
or more operations from the search path as we no longer need to compute the
value for the index to be shifted by and can instead just use the raw pos
value.

In addition the tkey_extract_bits is now defunct and can be replaced by
get_index since the two operations were doing the same thing, but now
get_index does it much more quickly as it is only an xor and shift versus a
pair of shifts and a subtraction.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch updates the fib_table_insert function to take advantage of the
changes made to improve the performance of fib_table_lookup.  As a result
the code should be smaller and run faster then the original.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes use of the same features I made use of for
fib_table_lookup to streamline fib_find_node.  The resultant code should be
smaller and run faster than the original.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch is meant to reduce the complexity of fib_table_lookup by reducing
the number of variables to the bare minimum while still keeping the same if
not improved functionality versus the original.

Most of this change was started off by the desire to rid the function of
chopped_off and current_prefix_length as they actually added very little to
the function since they only applied when computing the cindex.  I was able
to replace them mostly with just a check for the prefix match.  As long as
the prefix between the key and the node being tested was the same we know
we can search the tnode fully versus just testing cindex 0.

The second portion of the change ended up being a massive reordering.
Originally the calls to check_leaf were up near the start of the loop, and
the backtracing and descending into lower levels of tnodes was later.  This
didn't make much sense as the structure of the tree means the leaves are
always the last thing to be tested.  As such I reordered things so that we
instead have a loop that will delve into the tree and only exit when we
have either found a leaf or we have exhausted the tree.  The advantage of
rearranging things like this is that we can fully inline check_leaf since
there is now only one reference to it in the function.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes it so that leaf and tnode are the same struct.  As a
result there is no need for rt_trie_node anymore since everyting can be
merged into tnode.

On 32b systems this results in the leaf being 4 bytes larger, however I
don't know if that is really an issue as this and an eariler patch that
added bits & pos have increased the size from 20 to 28.  If I am not
mistaken slub/slab allocate on power of 2 sizes so 20 was likely being
rounded up to 32 anyway.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Both the leaf and the tnode had an rcu_head in them, but they had them in
slightly different places.  Since we now have them in the same spot and
know that any node with bits == 0 is a leaf and the rest are either vmalloc
or kmalloc tnodes depending on the value of bits it makes it easy to combine
the functions and reduce overhead.

In addition I have taken advantage of the rcu_head pointer to go ahead and
put together a simple linked list instead of using the tnode pointer as
this way we can merge either type of structure for freeing.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This change makes some fundamental changes to the way leaves and tnodes are
constructed.  The big differences are:
1.  Leaves now populate pos and bits indicating their full key size.
2.  Trie nodes now mask out their lower bits to be consistent with the leaf
3.  Both structures have been reordered so that rt_trie_node now consisists
    of a much larger region including the pos, bits, and rcu portions of
    the tnode structure.

On 32b systems this will result in the leaf being 4B larger as the pos and
bits values were added to a hole created by the key as it was only 4B in
length.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The trie usage stats were currently being shared by all threads that were
calling fib_table_lookup.  As a result when multiple threads were
performing lookups simultaneously the trie would begin to cache bounce
between those threads.

In order to prevent this I have updated the usage stats to use a set of
percpu variables.  By doing this we should be able to avoid the cache
bouncing and still make use of these stats.
Signed-off-by: NAlexander Duyck <alexander.h.duyck@redhat.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The GRE tap device supports Ethernet over GRE, but doesn't
care about the source address of the tunnel, therefore it
can be changed without bring device down.
Signed-off-by: NStephen Hemminger <stephen@networkplumber.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously l2tp module did not provide any means for the user space to
get notified when tunnels/sessions are added/modified/deleted.
This change contains the following
- create a multicast group for the listeners to register.
- notify the registered listeners when the tunnels/sessions are
  created/modified/deleted.
Signed-off-by: NBill Hong <bhong@brocade.com>
Reviewed-by: NStephen Hemminger <stephen@networkplumber.org>
Reviewed-by: NSven-Thorsten Dietrich <sven@brocade.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Instead of -1 with EAGAIN, read on a O_NONBLOCK tun fd will return 0.  This
fixes this by properly returning the error code from __skb_recv_datagram.
Signed-off-by: NAlex Gartrell <agartrell@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Validated that this was actually using the unsigned comparison with gdb.
Signed-off-by: NAlex Gartrell <agartrell@fb.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fix sparse warning:
net/tipc/link.c:1924:40: warning: Using plain integer as NULL pointer
Signed-off-by: NFabian Frederick <fabf@skynet.be>
Acked-by: NYing Xue <ying.xue@windriver.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Govindarajulu Varadarajan says:

====================
enic: Check for DMA mapping error

After dma mapping the buffers, enic does not call dma_mapping_error() to check
if mapping is successful.

This series fixes the issue by checking return value of pci_dma_mapping_error()
after pci_map_single().

This is reported by redhat here
https://bugzilla.redhat.com/show_bug.cgi?id=1145016
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds generic statistics for enic. As of now dma_map_error is the only
member. dma_map_erro is incremented every time dma maping error happens.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch checks for pci_dma_mapping_error() after dma mapping the data.
If the dma mapping fails we remove the previously queued frags and return
NETDEV_TX_OK.
Reported-by: NJan Stancek <jstancek@redhat.com>
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch makes vnic_wq_buf doubly liked list. This is needed for dma_mapping
error check, in case some frag's dma map fails, we need to move back and remove
previously queued buffers.
Signed-off-by: NGovindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Fugang Duan says:

====================
net: fec: add Wake-on-LAN support

The patch series enable FEC Wake-on-LAN feature for i.MX6q/dl and i.MX6SX SOCs.
FEC HW support sleep mode, when system in suspend status with FEC all clock gate
off, magic packet can wake up system. For different SOCs, there have special SOC
GPR register to let FEC enter sleep mode or exit sleep mode, add these to platform
callback for driver' call.

Patch#1: add WOL interface supports.
Patch#2: add SOC special sleep of/off operations for driver's sleep callback.
Patch#3: add magic pattern support for devicetree.
====================
Signed-off-by: NDavid S. Miller <davem@davemloft.net>