Skip to content

K
Kernel

openeuler / Kernel
1 年多 前同步成功

通知 8
Star 0
Fork 0
K
Kernel
切换分支/标签
  1. 08 4月, 2014 1 次提交
  3. 30 3月, 2014 1 次提交
  5. 29 3月, 2014 3 次提交
  7. 28 3月, 2014 3 次提交
  9. 27 3月, 2014 3 次提交
  11. 26 3月, 2014 5 次提交
  13. 25 3月, 2014 4 次提交
    • A
      spi: clps711x: Remove <mach/hardware.h> dependency · 3dc92594
      由 Alexander Shiyan 提交于 
      This patch removes <mach/hardware.h> dependency. This is performed
by replace hard coded used memory regions and interrupt to getting
these values from resources passed to the driver. For the system-wide
registers we now able to use SYSCON driver.
Signed-off-by: NAlexander Shiyan <shc_work@mail.ru>
Signed-off-by: NMark Brown <broonie@linaro.org>
      3dc92594
    • D
      vxlan: fix nonfunctional neigh_reduce() · 4b29dba9
      由 David Stevens 提交于 
      The VXLAN neigh_reduce() code is completely non-functional since
check-in. Specific errors:

1) The original code drops all packets with a multicast destination address,
	even though neighbor solicitations are sent to the solicited-node
	address, a multicast address. The code after this check was never run.
2) The neighbor table lookup used the IPv6 header destination, which is the
	solicited node address, rather than the target address from the
	neighbor solicitation. So neighbor lookups would always fail if it
	got this far. Also for L3MISSes.
3) The code calls ndisc_send_na(), which does a send on the tunnel device.
	The context for neigh_reduce() is the transmit path, vxlan_xmit(),
	where the host or a bridge-attached neighbor is trying to transmit
	a neighbor solicitation. To respond to it, the tunnel endpoint needs
	to do a *receive* of the appropriate neighbor advertisement. Doing a
	send, would only try to send the advertisement, encapsulated, to the
	remote destinations in the fdb -- hosts that definitely did not do the
	corresponding solicitation.
4) The code uses the tunnel endpoint IPv6 forwarding flag to determine the
	isrouter flag in the advertisement. This has nothing to do with whether
	or not the target is a router, and generally won't be set since the
	tunnel endpoint is bridging, not routing, traffic.

	The patch below creates a proxy neighbor advertisement to respond to
neighbor solicitions as intended, providing proper IPv6 support for neighbor
reduction.
Signed-off-by: NDavid L Stevens <dlstevens@us.ibm.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      4b29dba9
    • C
      net: davinci_emac: Fix rollback of emac_dev_open() · cd11cf50
      由 Christian Riesch 提交于 
      If an error occurs during the initialization in emac_dev_open() (the
driver's ndo_open function), interrupts, DMA descriptors etc. must be freed.
The current rollback code is buggy in several ways.

  1) Freeing the interrupts. The current code will not free all interrupts
     that were requested by the driver. Furthermore,  the code tries to do a
     platform_get_resource(priv->pdev, IORESOURCE_IRQ, -1) in its last
     iteration.

     This patch fixes these bugs.

  2) Wrong order of err: and rollback: labels. If the setup of the PHY in
     the code fails, the interrupts that have been requested before are
     not freed:

        request irq
                if requesting irqs fails, goto rollback
        setup phy
                if phy setup fails, goto err
        return 0

     rollback:
        free irqs
     err:

     This patch brings the code into the correct order.

  3) The code calls napi_enable() and emac_int_enable(), but does not
     undo both in case of an error.

     This patch adds calls of emac_int_disable() and napi_disable() to the
     rollback code.

  4) RX DMA descriptors are not freed in case of an error: Right before
     requesting the irqs, the function creates DMA descriptors for the
     RX channel. These RX descriptors are never freed when we jump to either
     rollback or err.

     This patch adds code for freeing the DMA descriptors in the case of
     an initialization error. This required a modification of
     cpdma_ctrl_stop() in davinci_cpdma.c: We must be able to call this
     function to free the DMA descriptors while the DMA channels are
     in IDLE state (before cpdma_ctlr_start() was called).

Tested on a custom board with the Texas Instruments AM1808.
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      cd11cf50
    • C
      net: davinci_emac: Replace devm_request_irq with request_irq · 33b7107f
      由 Christian Riesch 提交于 
      In commit 6892b41d

Author: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Date:   Tue Jun 25 21:24:51 2013 +0530
net: davinci: emac: Convert to devm_* api

the call of request_irq is replaced by devm_request_irq and the call
of free_irq is removed. But since interrupts are requested in
emac_dev_open, doing ifconfig up/down on the board requests the
interrupts again each time, causing devm_request_irq to fail. The
interface is dead until the device is rebooted.

This patch reverts said commit partially: It changes the driver back
to use request_irq instead of devm_request_irq, puts free_irq back in
place, but keeps the remaining changes of the original patch.
Reported-by: NJon Ringle <jon@ringle.org>
Signed-off-by: NChristian Riesch <christian.riesch@omicron.at>
Cc: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>
      33b7107f
  15. 24 3月, 2014 2 次提交
  17. 22 3月, 2014 6 次提交
  19. 20 3月, 2014 2 次提交
  21. 19 3月, 2014 10 次提交