Treat the VMA as the primary struct responsible for tracking bindings
into the GPU's VM. That is we want to treat the VMA returned after we
pin an object into the VM as the cookie we hold and eventually release
when unpinning. Doing so eliminates the ambiguity in pinning the object
and then searching for the relevant pin later.

v2: Joonas' stylistic nitpicks, a fun rebase.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1471254551-25805-27-git-send-email-chris@chris-wilson.co.uk

With NV12 we have two color planes to deal with so we must compute the
surface and x/y offsets for the second plane as well.

What makes this a bit nasty is that the hardware expects the surface
offset to be specified as a distance from the main surface offset.
What's worse, the distance must be non-negative (no neat wraparound or
anything). So we must make sure that the main surface offset is always
less or equal to the AUX surface offset. We do that by computing the AUX
offset first and the main surface offset second. If the main surface
offset ends up being above the AUX offset, we just push it down as far
as is required while still maintaining the required alignment etc.

Fortunately the AUX offset only reuqires 4K alignment, so we don't need
to do any of the backwards searching for an acceptable offset that we
must do for the main surface. And X tiled + NV12 isn't a supported
combination anyway.

Note that this just computes aux surface offsets, we do not yet program
them into the actual hardware registers, and hence we can't yet expose
NV12.

v2: Rebase due to drm_plane_state src/dst rects
    s/TODO.../something else/ in the commit message/ (Daniel)
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470821001-25272-12-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

SKL has nasty limitations with the display surface offsets:
* source x offset + width must be less than the stride for X tiled
  surfaces or the display engine falls over
* the surface offset requires lots of alignment (256K or 1M)

These facts mean that we can't just pick any suitably aligned tile
boundary as the offset and expect the resulting x offset to be useable.
The solution is to start with the closest boundary as before, but then
keep searching backwards until we find one that works, or don't. This
means we must be prepared to fail, hence the whole surface offset
calculation needs to be moved to the .check_plane() hook from the
.update_plane() hook.

While at it we can check that the source width/height don't exceed
maximum plane size limits.

We'll store the results of the computation in the plane state to make
it easy for the .update_plane() hook to do its thing.

v2: Replace for+break loop with while loop
    Rebase due to drm_plane_state src/dst rects
    Rebase due to plane_check_state()
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470821001-25272-11-git-send-email-ville.syrjala@linux.intel.com

intel_compute_tile_offset() and intel_add_fb_offsets() get passed the fb
and the rotation. As both of those come from the plane state we can just
pass that in instead.

For extra consitency pass the plane state to intel_fb_xy_to_linear() as
well even though it only really needs the fb.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470821001-25272-5-git-send-email-ville.syrjala@linux.intel.com

We repeat the SKL stride register value calculations a several places.
Move it into a small helper function.

v2: Rebase due to drm_plane_state src/dst rects
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMatthew Auld <matthew.auld@intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470821001-25272-4-git-send-email-ville.syrjala@linux.intel.com

intel_compute_page_offset() can dig up the correct pitch from the fb
itself, no need for the caller to pass it in.

A bit of extra care is needed for the lower level
_intel_compute_page_offset() since that one gets called before the
rotated pitch under intel_fb is populated. Note that we don't actually
call it with anything but DRM_ROTATE_0 there so we wouldn't actually
look up the rotated pitch there, but still, leave the pitch as something
the caller has to pass to _intel_compute_page_offset() as an
indicator that something is a bit special.

This leaves 'stride_div' in the skl plane update hooks as a mostly useless
variable so just get rid of it.

v2: Add a note why stride_div got nuked
v3: Extract intel_fb_pitch() since it can be useful later
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Daniel Vetter <daniel.vetter@ffwll.ch> (v2)
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470821001-25272-3-git-send-email-ville.syrjala@linux.intel.com

Redo the fb rotation handling in order to:
- eliminate the NV12 special casing
- handle fb->offsets[] properly
- make the rotation handling easier for the plane code

To achieve these goals we reduce intel_rotation_info to only contain
(for each plane) the rotated view width,height,stride in tile units,
and the page offset into the object where the plane starts. Each plane
is handled exactly the same way, no special casing for NV12 or other
formats. We then store the computed rotation_info under
intel_framebuffer so that we don't have to recompute it again.

To handle fb->offsets[] we treat them as a linear offsets and convert
them to x/y offsets from the start of the relevant GTT mapping (either
normal or rotated). We store the x/y offsets under intel_framebuffer,
and for some extra convenience we also store the rotated pitch (ie.
tile aligned plane height). So for each plane we have the normal
x/y offsets, rotated x/y offsets, and the rotated pitch. The normal
pitch is available already in fb->pitches[].

While we're gathering up all that extra information, we can also easily
compute the storage requirements for the framebuffer, so that we can
check that the object is big enough to hold it.

When it comes time to deal with the plane source coordinates, we first
rotate the clipped src coordinates to match the relevant GTT view
orientation, then add to them the fb x/y offsets. Next we compute
the aligned surface page offset, and as a result we're left with some
residual x/y offsets. Finally, if required by the hardware, we convert
the remaining x/y offsets into a linear offset.

For gen2/3 we simply skip computing the final page offset, and just
convert the src+fb x/y offsets directly into a linear offset since
that's what the hardware wants.

After this all platforms, incluing SKL+, compute these things in exactly
the same way (excluding alignemnt differences).

v2: Use BIT(DRM_ROTATE_270) instead of ROTATE_270 when rotating
    plane src coordinates
    Drop some spurious changes that got left behind during
    development
v3: Split out more changes to prep patches (Daniel)
    s/intel_fb->plane[].foo.bar/intel_fb->foo[].bar/ for brevity
    Rename intel_surf_gtt_offset to intel_fb_gtt_offset
    Kill the pointless 'plane' parameter from intel_fb_gtt_offset()
v4: Fix alignment vs. alignment-1 when calling
    _intel_compute_tile_offset() from intel_fill_fb_info()
    Pass the pitch in tiles in
    stad of pixels to intel_adjust_tile_offset() from intel_fill_fb_info()
    Pass the full width/height of the rotated area to
    drm_rect_rotate() for clarity
    Use u32 for more offsets
v5: Preserve the upper_32_bits()/lower_32_bits() handling for the
    fb ggtt offset (Sivakumar)
v6: Rebase due to drm_plane_state src/dst rects

Cc: Sivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NSivakumar Thulasimani <sivakumar.thulasimani@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470821001-25272-2-git-send-email-ville.syrjala@linux.intel.comAcked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Atm, we apply this workaround somewhat inconsistently at the following
points: driver loading, LVDS init, eDP PPS init, system resume. As this
workaround also affects registers other than PPS (timing, PLL) a more
consistent way is to apply it early after the PPS HW context is known to
be lost: driver loading, system resume and on VLV/CHV/BXT when turning
on power domains.

This is needed by the next patch that removes saving/restoring of the
PP_CONTROL register.

This also removes the incorrect programming of the workaround on HSW+
PCH platforms which don't have the register locking mechanism.

v2: (Ville)
- Don't apply the workaround on BXT.
- Simplify platform checks using HAS_DDI().
v3:
- Move the call of intel_pps_unlock_regs_wa() to the more
  logical vlv_display_power_well_init() (also fixing CHV) (Ville).
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470827254-21954-5-git-send-email-imre.deak@intel.com

Replace the private drm_rects/flags in intel_plane_state
with the ones now living in drm_plane_state.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469549224-1860-5-git-send-email-ville.syrjala@linux.intel.com

Only property creation uses the rotation as an index, so convert the
to figure the index when needed.

v2: Use the new defines to build the _MASK defines (Sean)

Cc: intel-gfx@lists.freedesktop.org
Cc: linux-arm-msm@vger.kernel.org
Cc: freedreno@lists.freedesktop.org
Cc: malidp@foss.arm.com
Cc: David Airlie <airlied@linux.ie>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Cc: Liviu Dudau <Liviu.Dudau@arm.com>
Cc: Sean Paul <seanpaul@chromium.org>
Acked-by: NLiviu Dudau <Liviu.Dudau@arm.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v1)
Signed-off-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Signed-off-by: NSean Paul <seanpaul@chromium.org>
Link: http://patchwork.freedesktop.org/patch/msgid/1469771405-17653-1-git-send-email-joonas.lahtinen@linux.intel.com

This reverts commit f64425a8.

active_streams will get totally out of whack with SST unless we
sync up with the hw state at readout, obviously! We don't yet
do that, so now the WARNs fire all the time. Let's revert :(
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470413142-26402-1-git-send-email-ville.syrjala@linux.intel.com
References: https://bugs.freedesktop.org/show_bug.cgi?id=95472#c14Acked-by: NChris Wilson <chris@chris-wilson.co.uk>

Rather than a mismash of struct drm_device *dev and struct
drm_i915_private *dev_priv being used freely within a function, be
consistent and only pass along dev_priv.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NJoonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-22-git-send-email-chris@chris-wilson.co.uk

In view of adding inline functions into the intel_frontbuffer section,
we first split the header into its own file so that we can integrate it
more easily with kerneldoc.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1470324762-2545-19-git-send-email-chris@chris-wilson.co.uk

s/active_mst_links/active_streams/ and use it also for SST. We can then
use this information in the hpd handling to see if the link is active
or not, and thus whether we may need to retrain.

Cc: Ander Conselvan de Oliveira <ander.conselvan.de.oliveira@intel.com>
Cc: Jim Bride <jim.bride@linux.intel.com>
Cc: Manasi D Navare <manasi.d.navare@intel.com>
Cc: Durgadoss R <durgadoss.r@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-6-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

The MST vs. SST selection should depend purely on the choice of the
connector/encoder. So don't try to determine the correct DDI mode
based on the intel_dp->is_mst, which simply tells us whether the sink
is in MST mode or not. Instead derive the information from the encoder
type. Since the link training code deals in non-fake encoders, we'll
also need to keep a second copy of that information around, which we'll
now designate as 'link_mst'.

Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1469717448-4297-4-git-send-email-ville.syrjala@linux.intel.comReviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Bspec says:
"Restriction : SRD must not be enabled when the PSR Setup time from DPCD
00071h is greater than the time for vertical blank minus one line."

Let's check for that and disallow PSR if we exceed the limit.

Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

DDI buffer prorgramming works quite differently depending on
the mode of the DDI port (DP/eDP/FDI vs. HDMI/DVI). Let's split
the function that does the programming into two matching variants
as well.
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1468328376-6380-7-git-send-email-ville.syrjala@linux.intel.com

This reverts commit b12e0ee2 ("drm/i915: Enable RC6 immediately"),
as it was never meant to be sent anywhere other than the bug report for
experimentation.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1469132179-4052-1-git-send-email-chris@chris-wilson.co.ukAcked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

Now that PCU communication is reasonably fast, we do not need to defer
RC6 initialisation to a workqueue.

References: https://bugs.freedesktop.org/show_bug.cgi?id=97017Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>

Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview

While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.

Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.

Changes since v1:
 - Add comment explaining the addition of the if
   (!mode_config->poll_running) in intel_hpd_init()
 - Remove unneeded if (!dev->mode_config.poll_enabled) in
   i915_hpd_poll_init_work()
 - Call to drm_helper_hpd_irq_event() after we disable polling
 - Add cancel_work_sync() call to intel_hpd_cancel_work()

Changes since v2:
 - Apparently dev->mode_config.poll_running doesn't actually reflect
   whether or not a poll is currently in progress, and is actually used
   for dynamic module paramter enabling/disabling. So now we instead
   keep track of our own poll_running variable in dev_priv->hotplug
 - Clean i915_hpd_poll_init_work() a little bit

Changes since v3:
 - Remove the now-redundant connector loop in intel_hpd_init(), just
   rely on intel_hpd_poll_enable() for setting connector->polled
   correctly on each connector
 - Get rid of poll_running
 - Don't assign enabled in i915_hpd_poll_init_work before we actually
   lock dev->mode_config.mutex
 - Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
   for doc purposes
 - Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
   intel_hpd_poll_enable()
 - Add some comments about racing not mattering in intel_hpd_poll_enable

Changes since v4:
 - Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
 - Drop the bool argument from intel_hpd_poll_init()
 - Remove redundant calls to intel_hpd_poll_init()
 - Rename poll_enable_work to poll_init_work
 - Add some kerneldoc for intel_hpd_poll_init()
 - Cross-reference intel_hpd_poll_init() in intel_hpd_init()
 - Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()

Changes since v5:
 - Minor kerneldoc nitpicks

Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLyude <cpaul@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 19625e85)

While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:

      - Disconnect all monitors
      - Connect VGA
      - Disconnect VGA
      - Connect HDMI

Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.

Changes since v3:
 - Expose intel_crt_reset() through intel_drv.h and call that in
   vlv_display_power_well_init() instead of
   encoder->base.funcs->reset(&encoder->base);

Changes since v2:
 - Use intel_encoder structs instead of drm_encoder structs

Changes since v1:
 - Instead of handling the register writes ourself, we just reuse
   intel_crt_detect()
 - Instead of resetting the ADPA during display IRQ installation, we now
   reset them in vlv_display_power_well_init()

Cc: stable@vger.kernel.org
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLyude <cpaul@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
(cherry picked from commit 9504a892)

Unfortunately, there's two situations where we lose hpd right now:
- Runtime suspend
- When we've shut off all of the power wells on Valleyview/Cherryview

While it would be nice if this didn't cause issues, this has the
ability to get us in some awkward states where a user won't be able to
get their display to turn on. For instance; if we boot a Valleyview
system without any monitors connected, it won't need any of it's power
wells and thus shut them off. Since this causes us to lose HPD, this
means that unless the user knows how to ssh into their machine and do a
manual reprobe for monitors, none of the monitors they connect after
booting will actually work.

Eventually we should come up with a better fix then having to enable
polling for this, since this makes rpm a lot less useful, but for now
the infrastructure in i915 just isn't there yet to get hpd in these
situations.

Changes since v1:
 - Add comment explaining the addition of the if
   (!mode_config->poll_running) in intel_hpd_init()
 - Remove unneeded if (!dev->mode_config.poll_enabled) in
   i915_hpd_poll_init_work()
 - Call to drm_helper_hpd_irq_event() after we disable polling
 - Add cancel_work_sync() call to intel_hpd_cancel_work()

Changes since v2:
 - Apparently dev->mode_config.poll_running doesn't actually reflect
   whether or not a poll is currently in progress, and is actually used
   for dynamic module paramter enabling/disabling. So now we instead
   keep track of our own poll_running variable in dev_priv->hotplug
 - Clean i915_hpd_poll_init_work() a little bit

Changes since v3:
 - Remove the now-redundant connector loop in intel_hpd_init(), just
   rely on intel_hpd_poll_enable() for setting connector->polled
   correctly on each connector
 - Get rid of poll_running
 - Don't assign enabled in i915_hpd_poll_init_work before we actually
   lock dev->mode_config.mutex
 - Wrap enabled assignment in i915_hpd_poll_init_work() in READ_ONCE()
   for doc purposes
 - Do the same for dev_priv->hotplug.poll_enabled with WRITE_ONCE in
   intel_hpd_poll_enable()
 - Add some comments about racing not mattering in intel_hpd_poll_enable

Changes since v4:
 - Rename intel_hpd_poll_enable() to intel_hpd_poll_init()
 - Drop the bool argument from intel_hpd_poll_init()
 - Remove redundant calls to intel_hpd_poll_init()
 - Rename poll_enable_work to poll_init_work
 - Add some kerneldoc for intel_hpd_poll_init()
 - Cross-reference intel_hpd_poll_init() in intel_hpd_init()
 - Just copy the loop from intel_hpd_init() in intel_hpd_poll_init()

Changes since v5:
 - Minor kerneldoc nitpicks

Cc: stable@vger.kernel.org
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLyude <cpaul@redhat.com>
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

While VGA hotplugging worked(ish) before, it looks like that was mainly
because we'd unintentionally enable it in
valleyview_crt_detect_hotplug() when we did a force trigger. This
doesn't work reliably enough because whenever the display powerwell on
vlv gets disabled, the values set in VLV_ADPA get cleared and
consequently VGA hotplugging gets disabled. This causes bugs such as one
we found on an Intel NUC, where doing the following sequence of
hotplugs:

      - Disconnect all monitors
      - Connect VGA
      - Disconnect VGA
      - Connect HDMI

Would result in VGA hotplugging becoming disabled, due to the powerwells
getting toggled in the process of connecting HDMI.

Changes since v3:
 - Expose intel_crt_reset() through intel_drv.h and call that in
   vlv_display_power_well_init() instead of
   encoder->base.funcs->reset(&encoder->base);

Changes since v2:
 - Use intel_encoder structs instead of drm_encoder structs

Changes since v1:
 - Instead of handling the register writes ourself, we just reuse
   intel_crt_detect()
 - Instead of resetting the ADPA during display IRQ installation, we now
   reset them in vlv_display_power_well_init()

Cc: stable@vger.kernel.org
Acked-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: NLyude <cpaul@redhat.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
[danvet: Rebase over dev_priv/drm_device embedding.]
Signed-off-by: NDaniel Vetter <daniel.vetter@ffwll.ch>

This function is no longer used outside of intel_pm.c so we can stop
exposing it and rename the __gen6_update_ring_freq() to take its place.
Suggested-by: NMika Kuoppala <mika.kuoppala@intel.com>
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468397438-21226-8-git-send-email-chris@chris-wilson.co.uk

Some hardware requires a valid render context before it can initiate
rc6 power gating of the GPU; the default state of the GPU is not
sufficient and may lead to undefined behaviour. The first execution of
any batch will load the "golden render state", at which point it is safe
to enable rc6. As we do not forcibly load the kernel context at resume,
we have to hook into the batch submission to be sure that the render
state is setup before enabling rc6.

However, since we don't enable powersaving until that first batch, we
queued a delayed task in order to guarantee that the batch is indeed
submitted.

v2: Rearrange intel_disable_gt_powersave() to match.
v3: Apply user specified cur_freq (or idle_freq if not set).
v4: Give in, and supply a delayed work to autoenable rc6
v5: Mika suggested a couple of better names for delayed_resume_work
v6: Rebalance rpm_put around the autoenable task
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1468397438-21226-7-git-send-email-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

Now that the last couple of hacks have been removed from the runtime
powermanagement users, we can fully enable the asserts by preventing the
temptation to disable them when our code is buggy.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1468055535-19740-11-git-send-email-chris@chris-wilson.co.ukReviewed-by: NMika Kuoppala <mika.kuoppala@intel.com>

has_dsi_encoder was introduced to indicate that the pipe is driving
a DSI encoder. Now that we have the output_types bitmask that can
tell us the same thing, let's just kill has_dsi_encoder.

v2: Rebase, handle BXT DSI transcoder, rewrote commit message

Cc: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-10-git-send-email-ville.syrjala@linux.intel.com

INTEL_OUTPUT_DISPLAYPORT hsa been bugging me for a long time. It always
looks out of place besides INTEL_OUTPUT_EDP and INTEL_OUTPUT_DP_MST.
Let's just rename it to INTEL_OUTPUT_DP.

v2: Rebase
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMika Kahola <mika.kahola@intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-9-git-send-email-ville.syrjala@linux.intel.com

Use the new output_types bitmask instead of has_dp_encoder.
To make it less oainlful provide a small helper
(intel_crtc_has_dp_encoder()) to do the bitsy stuff.

v2: Rebase
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-7-git-send-email-ville.syrjala@linux.intel.com

With the introduction of the output_types mask, intel_pipe_has_type()
and intel_pipe_will_have_type() are basically the same thing. Replace
them with a new intel_crtc_has_type() (identical to
intel_pipe_will_have_type() actually).

v2: Rebase
v3: Make intel_crtc_has_type() static inline (Chris)

Cc: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> (v2)
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-5-git-send-email-ville.syrjala@linux.intel.com

Rather than looping through encoders to see which encoder types
are being driven by the pipe, add an output_types bitmask into
the crtc state and populate it prior to compute_config and during
state readout.

v2: Determine output_types before .compute_config() hooks are called
Signed-off-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NMaarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466621833-5054-4-git-send-email-ville.syrjala@linux.intel.com

Since we now subclass struct drm_device, we can save pointer dances by
noting the equivalence of struct drm_device and struct drm_i915_private,
i.e. by using to_i915().

   text    data     bss     dec     hex filename
1073824    4562     416 1078802  107612 drivers/gpu/drm/i915/i915.ko
1068976    4562     416 1073954  106322 drivers/gpu/drm/i915/i915.ko

Created by the coccinelle script:

@@
expression E;
identifier p;
@@
- struct drm_i915_private *p = E->dev_private;
+ struct drm_i915_private *p = to_i915(E);
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: NDave Gordon <david.s.gordon@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1467628477-25379-1-git-send-email-chris@chris-wilson.co.uk

usleep_range is not recommended for waits shorten than 10us.

Make the wait_for_us use the atomic variant for such waits.

To do so we need to reimplement the _wait_for_atomic macro to
be safe with regards to preemption and interrupts.

v2: Reimplement _wait_for_atomic to be irq and preemption safe.
    (Chris Wilson and Imre Deak)

v3: Fixed in_atomic check due rebase error.
v4: Build bug on non-constant timeouts.
v5: Compile away cpu migration code in atomic paths.
Signed-off-by: NTvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Imre Deak <imre.deak@intel.com>
Cc: Mika Kuoppala <mika.kuoppala@intel.com>
Reviewed-by: NChris Wilson <chris@chris-wilson.co.uk>
Link: http://patchwork.freedesktop.org/patch/msgid/1467114710-29989-1-git-send-email-tvrtko.ursulin@linux.intel.com

Currently the backlight is being registered in the load phase (before
the display and its objects are registered). Move the backlight
registration into the analogous phase by performing it from the
connector registration, just after its creation.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-3-git-send-email-chris@chris-wilson.co.uk

Currently setting up the backlight for a panel is sometimes done
together with initialising the panel, and sometimes after the connector
is registered. The backlight setup does not depend upon connector
registration (i.e. access to sysfs/debugfs and the kobject hierachy) so
perform it consistently just after panel initialisation.

Note the discrepancy here as destroying the panel is done during
connector unregistration...
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466773227-7994-1-git-send-email-chris@chris-wilson.co.uk

The PPS registers are backed by power well #0 and as such may be reset
after system or runtime suspend (both implying a possible DC9
transition). Fix this by reusing the VLV/CHV PPS pipe-reassignment
logic. The difference on BXT is that the PPS instances are not pipe but
port (or more accurately pin) specific, so we only need to care about
the lost HW state. As opposed to VLV/CHV the SW state is fixed and
initialized during connector init.

This also paves the way towards using the actual port->PPS instance
mapping based on VBT.

This fixes eDP link training errors on BXT after suspend, where we
started the link training too early due to an incorrect T3 (panel power
on) register value.

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=96436Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: NVille Syrjälä <ville.syrjala@linux.intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466084243-5388-2-git-send-email-imre.deak@intel.com

Atm on IBX/CPT we attempt to detect if eDP is present even if LVDS was
already detected and an encoder for it was registered. This involves
trying to read out the eDP DPCD, which in turn needs the same power
sequencer that LVDS uses. Poking at the VDD line at an unexpected time
may or may not interfere with the LVDS panel, but it's probably safer to
prevent this. Registering both an LVDS and an eDP connector would also
present a similar problem accessing the shared PPS at any point later in
an unexpected way.

We also need this to be able fix PPS initialization before its first use
in the next patch. For that we want to be sure that PPS is not in use
by LVDS.

v2:
- Split out the PPS init fix to a separate patch. (Chris)
- Add comment about eDP init depending on LVDS init. (Chris)
- Make the use of the intel_encoder ptr less error prone.
v3:
- Use IBX/CPT reference instead of the incorrect ILK, add a WARN about
  this. (Ville)
v4:
- Use a helper to get the lvds encoder instead of opencoding the same.
  (Ville)

CC: Ville Syrjälä <ville.syrjala@linux.intel.com>
CC: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: NImre Deak <imre.deak@intel.com>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk> (v2)
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com> (v3)
Link: http://patchwork.freedesktop.org/patch/msgid/1466499109-20240-2-git-send-email-imre.deak@intel.com

It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.

This is a manual revert of commits 5fa836a9 ("drm/i915: DP link
training optimization") and 4e96c977 ("drm/i915: eDP link training
optimization").

Fixes: 5fa836a9 ("drm/i915: DP link training optimization")
Fixes: 4e96c977 ("drm/i915: eDP link training optimization")
Cc: <stable@vger.kernel.org> # v4.2+

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com
(cherry picked from commit 91df09d9)

During cleanup we have to synchronise with the async task we are using
to initialise and register our fbdev. Currently, we are using a full
synchronisation on the global domain, but we can restrict this to just
synchronising up to our task if we remember our cookie.

Whilst there, streamline the function parameters.

v2: async_synchronize_cookie() takes an exclusive upper bound, to
synchronize with our task we have to pass in the next cookie.
v3: Drop premature disregarding of the active cookie (we need to wait
until the task is complete before continuing in the teardown).
v4: Refactor waiting on async to incorporate a comment explaining why we
need the +1.
Signed-off-by: NChris Wilson <chris@chris-wilson.co.uk>
Cc: Lukas Wunner <lukas@wunner.de>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Reviewed-by: NDaniel Vetter <daniel.vetter@ffwll.ch>
Link: http://patchwork.freedesktop.org/patch/msgid/1466497015-8509-2-git-send-email-chris@chris-wilson.co.uk

It has been found out that in some HW combination the DisplayPort
fast link training feature caused screen flickering. Let's revert
this feature for now until we can ensure that the feature works for
all platforms.

This is a manual revert of commits 5fa836a9 ("drm/i915: DP link
training optimization") and 4e96c977 ("drm/i915: eDP link training
optimization").

Fixes: 5fa836a9 ("drm/i915: DP link training optimization")
Fixes: 4e96c977 ("drm/i915: eDP link training optimization")
Cc: <stable@vger.kernel.org> # v4.2+

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=91393Reviewed-by: NJani Nikula <jani.nikula@intel.com>
Signed-off-by: NMika Kahola <mika.kahola@intel.com>
Signed-off-by: NJani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1466410226-19543-1-git-send-email-mika.kahola@intel.com