omap3_check_revision() does not depend on omap3_check_features()
move this above so that we can add logic based on revision
detected in check_features.
Signed-off-by: NNishanth Menon <nm@ti.com>
Acked-by: NMika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: NTony Lindgren <tony@atomide.com>

For ease of use it is preferrable to build in HSMMC driver
rather than build it as kernel module. This patches updates
default configuration for omap3evm to reflect this change.
Signed-off-by: NSriramakrishnan <srk@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support for omap hsmmc2 8-bit mux configuration.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The speed ctrl bit for MMC I/O is part of CONTROL_PROG_IO1 register
in omap3630.This patch sets it up accordingly.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The HSMMC1 controller on omap3630 supprts only 4-bit mode. If cpu
is 3630 configure HSMMC1 wires to 4-bit.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Change the cpu_is_omap3430() check to cpu_is_omap34xx() to allow HSMMC1/2
mux configuration for omap3630.
Signed-off-by: NMadhusudhan Chikkature <madhu.cr@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The use of the spin lock, which supposed to protect the the
dma_op_mode causing "INFO: inconsistent lock state" on
playback start.
Remove the spin locks around the dma_op_mode, when it's
purpuse is to protect the dma_op_mode.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NJarkko Nikula <jhnikula@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

This way it's more object oriented and easier to see what is happening.
No functional changes.
Signed-off-by: NFelipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Cache flush operation is handled in the upper client layer and iovmm
modules doesn't have to care about it. This patch will improve some
performance with current camera isp driver.
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

MPU side (v)-(p) mapping is necessary only if IOVMF_MMIO is set in
"flags".
Signed-off-by: NHiroshi DOYU <Hiroshi.DOYU@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add platform init code for EHCI driver.

Various fixes to the original patch by Ajay Kumar Gupta <ajay.gupta@ti.com>
and Anand Gadiyar <gadiyar@ti.com>.

Overo support added by Olof Johansson <olof@lixom.net>
Beagle support added by Koen Kooi <koen@beagleboard.org>
CM-T32 support added by Mike Rapoport <mike@compulab.co.il>
Signed-off-by: NSigned-off-by: Olof Johansson <olof@lixom.net>
Acked-by: NSteve Sakoman <steve@sakoman.com>
Signed-off-by: NKoen Kooi <koen@beagleboard.org>
Signed-off-by: NMike Rapoport <mike@compulab.co.il>
Signed-off-by: NAjay Kumar Gupta <ajay.gupta@ti.com>
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Signed-off-by: NFelipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add missing declarations to allow the recently introduced
ehci-omap driver to build on OMAP3
Signed-off-by: NAnand Gadiyar <gadiyar@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NGreg Kroah-Hartman <gregkh@suse.de>

AM35xx is functionally similar to OMAP3430 ES3.1 from a
powerdomain/clockdomain perspective. This patch initializes the
omap_chip bits on AM35xx for use by powerdomain and clockdomain code.
Signed-off-by: NRanjith Lohithakshan <ranjithl@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add support to detect AM3505/AM3517 devices at runtime.
Also updates the CPU names printed during boot.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

3630 is getting treated like next rev of 3430
omap_chip.oc variable has to be updated for 3630 version

Otherwise the Core power domain is not getting registered.

This gets used in the registration of power domains in:
"arch/arm/mach-omap2/powerdomains34xx.h"
core_34xx_es3_1_pwrdm
OMAP_CHIP_INIT(CHIP_GE_OMAP3430ES3_1)

Core power doman will get registered for 3630 only when .oc is
populated correctly.

Tested on Zoom3(3630) board
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Acked-by: NAlexander Shishkin <virtuoso@slind.org>
Acked-by: NAri Kauppi <kauppi@papupata.org>
Acked-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

OMAP3630 is the latest in the family of OMAP3 devices
and among the changes it introduces are:

New OPP levels for new voltage and frequency levels. a bunch of
Bug fixes to various modules feature additions, notably with ISP,
sDMA etc.

Details about the chip is available here:
http://focus.ti.com/general/docs/wtbu/wtbuproductcontent.tsp?templateId=6123&navigationId=12836&contentId=52606

Strategy used:
Strategy to introduce this device into Linux was discussed here:
Ref: http://marc.info/?t=125343303400003&r=1&w=2

Two approaches were available:
a) Consider 3630 generation of devices as a new family of silicon
b) Consider 3630 as an offshoot of 3430 family of devices

As a common consensus, (b) seems to be more valid for 3630 as:
* There are changes which are easily handled by using "FEATURES"
  infrastructure.
  For details how to do this, see thread:
  http://marc.info/?t=125050998500001&r=1&w=2
* Most of existing 34xx infrastructure can be reused(almost 90%+)
	- so no ugly if (cpu_is_omap34xx() || cpu_is_omap36xx())
	  all over the place
	- lesser chance of bugs due to reuse of proven code flow
	- 36xx specific handling can still be done where required
	  within the existing infrastructure

NOTE:
* If additional 34xx series are added, OMAP3430_REV_ESXXXX can be
  added on top of the existing 3630 ones are renumbered

This patch was tested on SDP3430, boot tested on 3630 platform using
3430sdp defconfig
Signed-off-by: NMadhusudhan Chikkature Rajashekar <madhu.cr@ti.com>
Signed-off-by: NNishanth Menon <nm@ti.com>
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Cc: Allen Pais <allen.pais@ti.com>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Felipe Balbi <felipe.balbi@nokia.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Sanjeev Premi <premi@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Sergio Alberto Aguirre Rodriguez <saaguirre@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Add runtime check for these OMAP35x variations
based on the detected Si features:
  OMAP3503, OMAP3515, OMAP3525 and OMA3530.

Also, delayed the call to pr_info() into actual
variant is detected in omap3_cpuinfo()
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The OMAP35x family has multiple variants differing
in the HW features. This patch detects these features
at runtime and prints information during the boot.

Since most of the code seemed repetitive, macros
have been used for readability.
Signed-off-by: NSanjeev Premi <premi@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The l3_ocpi_ck clock is needed on omap7xx processors for USB.
Additionally, bit 8 of the SOFT_REQ_REG needs to be enabled for
the usb_dc_ck on omap7xx, which is a different bit than that
of the omap16xx-defined clock of the same name.

I added a provision for the usb_dc_ck and l3_ocpi_ck clocks as
dc_clk and hhc_clk, respectively, for omap7xx CPUs.  Additionally,
I added a check in machine_without_vbus_sense for all omap7xx
devices, as presently I know of no omap7xx-based devices that
have vbus sense, and it made more sense to me to use a cpu check
here than to spell out each machine one at a time.  Finally, DMA
is disabled for omap7xx, as it causes problems with these chips.

Cc: linux-usb@vger.kernel.org
Cc: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

The MMC mux pins normally used by omap chips in devices.c
are different from what is needed by omap7xx chips.  This
change adds a conditional around the mux setup code to
enable the correct mux pins.

The omap730 and omap850 both use a different clock for the "fck"
clock of the MMC interface than other omap processors based on the
SOFT_REQ_REG, pin 12.  The "ick" clock is the same as that used
by other omap processors.

* Added the missing clock definition as mmc3_ck to clock.h
* Added the clock definition to omap_clks in clock.c
* Added CK_7XX to the mmci-omap.0 "ick" clock already in clock.c

With these changes, it is now possible to initialize and use MMC
cards with omap730 and omap850 devices.
Signed-off-by: NCory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Zoom2/Zoom3 kind of boards do not use omap uarts for console.
These use external debug board for console.

So these boards should not have "Uncompressing Kernel...."
log put on omap uarts.

By interoducing OMAP_LL_DEBUG_NONE option,
unnecessary writes to omap uarts is avoided.

In future, the DEBUG_LL interface will be enhanced
to use external debug board.
Signed-off-by: NVikram Pandita <vikram.pandita@ti.com>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Eliminate OMAP_MAX_NR_PORTS

Note that also the null terminator entry for omap1
serial_platform_data needs to be now removed to avoid
oopsing.

Note that mach-omap1 uses struct plat_serial8250_port
array, which requires a null terminator at the end,
and that's why we need to use ARRAY_SIZE - 1. This
is not needed on mach-omap2 as the array used is
struct omap_uart_state, and does not use a null
terminator.
Signed-off-by: NAlexander Shishkin <virtuoso@slind.org>
Acked-by: NKevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: NLadislav Michl <ladis@linux-mips.org>
Signed-off-by: NTony Lindgren <tony@atomide.com>

Initialize some of the RX-51 input GPIO lines as gpio keys. Enable gpio
keys as a module in rx51_defconfig.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Add new codes for camera focus key, and camera lens cover, keypad slide,
front proximity switches.
Signed-off-by: NJani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: NDmitry Torokhov <dtor@mail.ru>

Configure the APLL_INFREQ field in the APLL_CTL register
based on the platform data.
Provide also a function for childs to query the audio_mclk
frequency.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

audio_mclk value is going to be handled by the
twl4030-codec MFD driver, configure the correct
value for boards, which is using the twl4030 audio.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add audio_mclk to the platform data struct for the
twl4030-codec MFD driver.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Add needed platform data for the twl4030_codec MFD on boards,
where the audio part of the twl4030 codec is used.
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NTony Lindgren <tony@atomide.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

New MFD child to twl4030 MFD device.

Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.

This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.

The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: NPeter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: NSamuel Ortiz <sameo@linux.intel.com>
Signed-off-by: NMark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch '7xx-iosplit-plat-merge' into omap-for-linus

* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
  SUNRPC: Address buffer overrun in rpc_uaddr2sockaddr()
  NFSv4: Fix a cache validation bug which causes getcwd() to return ENOENT

As this struct is exposed to user space and the API was added for this
release it's a bit of a pain for the C++ world and we still have time to
fix it. Rename the fields before we end up with that pain in an actual
release.
Signed-off-by: NAlan Cox <alan@linux.intel.com>
Reported-by: Olivier Goffart
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

Commit 86cf898e ("intel-iommu: Check for
'DMAR at zero' BIOS error earlier.") was supposed to work by pretending
not to detect an IOMMU if it was actually being reported by the BIOS at
physical address zero.

However, the intel_iommu_init() function is called unconditionally, as
are the corresponding functions for other IOMMU hardware.

So the patch only worked if you have RAM above the 4GiB boundary. It
caused swiotlb to be initialised when no IOMMU was detected during early
boot, and thus the later IOMMU init would refuse to run.

But if you have less RAM than that, swiotlb wouldn't get set up and the
IOMMU _would_ still end up being initialised, even though we never
claimed to detect it.

This patch also sets the dmar_disabled flag when the error is detected
during the initial detection phase -- so that the later call to
intel_iommu_init() will return without doing anything, regardless of
whether swiotlb is used or not.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/davej/cpufreq:
  [CPUFREQ] Fix stale cpufreq_cpu_governor pointer
  [CPUFREQ] Resolve time unit thinko in ondemand/conservative govs
  [CPUFREQ] speedstep-ich: fix error caused by 394122ab
  [CPUFREQ] Fix use after free on governor restore
  [CPUFREQ] acpi-cpufreq: blacklist Intel 0f68: Fix HT detection and put in notification message
  [CPUFREQ] powernow-k8: Fix test in get_transition_latency()
  [CPUFREQ] longhaul: select Longhaul version 2 for capable CPUs

Doing the strcmp return value as

	signed char __res = *cs - *ct;

is wrong for two reasons.  The subtraction can overflow because __res
doesn't use a type big enough.  Moreover the compared bytes should be
interpreted as unsigned char as specified by POSIX.

The same problem is fixed in strncmp.
Signed-off-by: NUwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Michael Buesch <mb@bu3sch.de>
Cc: Andreas Schwab <schwab@linux-m68k.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: NLinus Torvalds <torvalds@linux-foundation.org>

* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
  agp/intel-agp: Set dma_mask for capable chipsets before agp_add_bridge()

Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jmorris/security-testing-2.6:
  ima: replace GFP_KERNEL with GFP_NOFS

We should set this before calling agp_add_bridge() so that it's done
before we map the scratch page too.

This should probably fix the regression reported as k.o. bug #14627.
Signed-off-by: NDavid Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: NDave Airlie <airlied@redhat.com>

Merge branch 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6

* 'omap-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6:
  OMAP: cs should be positive in gpmc_cs_free()
  omap: fix unlikely(x) < y
  omap3: clock: Fixed dpll3_m2x2 rate calculation
  omap3: clock: Fix the DPLL freqsel computations
  omap: Fix keymap for zoom2 according to matrix keypad framwork