Currently when there is share buffer in the SSU(storage
switching unit), the low waterline for RX private buffer is
too low to keep the hardware running. Hardware may have
processed all the packet stored in the private buffer of the
low waterline before the new packet comes, because hardware
only tell the peer send packet again when the private buffer
is under the low waterline.

So this patch only allocate RX private buffer if there is
enough buffer according to hardware user manual.

This patch also reserve some buffer for reusing when TC num
is less than or equal to 2, and change PAUSE_TRANS_GAP &
HCLGE_NON_DCB_ADDITIONAL_BUF according to hardware user
manual.
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

If we failed to enable NIC HW error interrupts during client
initialization in some cases, we should do exception handling to clear
flags and free the resources.

Fixes: 00ea6e5f ("net: hns3: delay and separate enabling of NIC and ROCE HW errors")
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ROCE HW errors should only be enabled when initializing ROCE's
client, the current code enable it no matter initializing NIC or
ROCE client.

So this patch fixes it.

Fixes: 00ea6e5f ("net: hns3: delay and separate enabling of NIC and ROCE HW errors")
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When loading or unloading module, it should wait for the reset task
done before it un-initializes the client, otherwise the reset task
may cause a NULL pointer reference.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing global reset, the MAC autoneg state of fibre
port is set to default, which may cause user configuration
lost. This patch fixes it by restore the MAC autoneg state
after reset.

Fixes: 22f48e24 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When HW is resetting, firmware is unable to handle commands
from driver. So if remove VLAN device from stack at this time,
it will fail to remove the VLAN ID from HW VLAN filter, then
the VLAN filter status is unsynced with stack.

This patch fixes it by recording the VLAN ID delete failed,
and removes them again when reset complete.

Fixes: 44e626f7 ("net: hns3: fix VLAN offload handle for VLAN inserted by port")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

For VF VLAN filter is disabled when VF VLAN table is full, then the
new VLAN ID won't be added into VF VLAN table, it will always print
fail log when remove these VLAN IDs. If user has added too many
VLANs, it will cause massive verbose print logs.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When doing selftest for fibre port with autoneg on, the MAC speed
may be incorrect, which may cause the selftest failed. This patch
fixes it by halting autoneg during the selftest.

Fixes: 22f48e24 ("net: hns3: add autoneg and change speed support for fibre port")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch does following things:
1. add the keyword const before some variables which won't be modified
   in functions.
2. changes some variables from signed to unsigned to avoid bitwise
   operation on signed variables.
3. adds or removes initialization of some variables.
4. defines a new structure to help parsing mailbox messages instead of
   using an array which is harder to get the meaning of each element.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

IMP will set restting state for all function when PF FLR, driver
just clear the restting state in resetting progress, but don't do
it in initializing progress. As FLR is not created by driver,
it is necessary to clear restting state when initializing HW device.
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds the recovery for the HNS H/W errors which occurred
before the driver initialization.
Reported-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Presently the HNS driver enables the HNS H/W error interrupts after
the dev initialization is completed. However some exceptions such as
NCSI errors can occur when the network port driver is not loaded
and those errors required reporting to the BMC.
Therefore the firmware enabled all the HNS ras error interrupts
before the driver is loaded. And in some cases, there will be some
H/W errors remained unclear before reboot. Thus the HNS driver needs
to process and recover those hw errors occurred before HNS driver is
initialized.

This patch adds processing of the HNS hw errors(RAS and MSI-X)
which occurred before the driver initialization. For RAS, because
they are enabled by firmware, so we can detect specific bits, then
log and clear them. But for MSI-X which can not be enabled before
open vector0 irq, we can't detect the specific error bits, so we
just write 1 to all interrupt source registers to clear.
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Presently the error handling code sets the reset level required
for the recovery of the hw errors to the reset framework in the
error_detected AER callback. However the rest_event would be
called later from the slot_reset callback. This can cause issue
of using the wrong reset_level if a high priority reset request
occur before the slot_reset is called.

This patch delays setting of the reset level, required
for the hw errors, to the reset framework until the
slot_reset is called.
Reported-by: NSalil Mehta <salil.mehta@huawei.com>
Signed-off-by: NShiju Jose <shiju.jose@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch fixes some coding style issues reported by some static code
analysis tools and code review, such as modify some comments, rename
some variables, log some errors in detail, and fixes some alignment
errors.

BTW, these cleanups do not change the logic of code.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuiSong Li <lihuisong@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch deletes some redundant code and refactors some bloated
functions.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to make it more readable, this patch modifies PF/VF's
RSS hash key configuring function.
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds some macros instead of magic numbers in serval places
Signed-off-by: NYufeng Mo <moyufeng@huawei.com>
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NYunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to improve readability, this patch uses macros to
replace some magic numbers, and adds some comments for some
others.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since HNAE3_CLIENT_UNIC and HNAE3_DEV_UNIC is not used any more,
this patch removes the redundant codes.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Remove references to HCLGE_MAC_ETHERTYPE_LLDP and use ETH_P_LLDP instead.
Signed-off-by: NAnirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: NAndrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: NJeff Kirsher <jeffrey.t.kirsher@intel.com>

All RAS and MSI-X should be enabled just in the final stage of HNS3
initialization. It means that they should be enabled in
hclge_init_xxx_client_instance instead of hclge_ae_dev(). Especially
MSI-X, if it is enabled before opening vector0 IRQ, there are some
chances that a MSI-X error will cause failure on initialization of
 NIC client instane. So this patch delays enabling of HW errors.
Otherwise, we also separate enabling of ROCE RAS from NIC, because
it's not reasonable to enable ROCE RAS if we even don't have a ROCE
driver.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In orginal codes, the driver only restore VLAN filter entries
for PF after reset, the VLAN entries of VF will lose in this
case.

This patch fixes it by recording VLAN IDs for each function
when add VLAN, and restore the VLAN IDs after reset.

Fixes: 681ec399 ("net: hns3: fix for vlan table lost problem when resetting")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

VF VLAN table can only support no more than 256 VLANs. When user
adds too many VLANs, the VF VLAN table will be full, and firmware
will close the VF VLAN table for the function. When VF VLAN table
is full, and user keeps adding new VLANs, it's unnecessary to
configure the VF VLAN table, because it will always fail, and print
warning message. The worst case is adding 4K VLANs, and doing reset,
it will take much time to restore these VLANs, which may cause VF
reset fail by timeout.

Fixes: 6c251711 ("net: hns3: Disable vf vlan filter when vf vlan table is full")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Since core reset is similar to the global reset, so this
patch removes it and uses global reset to replace it.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When unloading driver, the reset task should not be scheduled
anymore. If disable IRQ before cancel ongoing reset task,
the IRQ may be re-enabled by the reset task.

This patch uses HCLGE_STATE_REMOVING/HCLGEVF_STATE_REMOVING
flag to indicate that the driver is unloading, and we should
stop new coming reset service to be scheduled, otherwise,
reset service will access some resource which has been freed
by unloading.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When reset happens, the hardware reset should begin after the
driver has finished its preparatory work, otherwise it may cause
some hardware error.

Before Hardware's reset, it will wait for the driver to write
bit HCLGE_NIC_CMQ_ENABLE of register HCLGE_NIC_CSQ_DEPTH_REG
to 1, while the driver finishes its preparatory work will do that.
BTW, since some cases this register will be cleared, so it needs
some sync time before driver's writing.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

hclge_init_client_instance() is a little bloated and there is
some duplicated code. This patch adds some cleanup for it.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PF ROCE client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_ROCE_REGISTERED
to indicate that. And before calling PF ROCE client's uninit_instance(),
we clear this state.

So any operation of the ROCE client from HCLGE is not allowed if this
state is not set.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

When PF NIC client's init_instance() succeeds, it means this client
has been registered successfully, so we use HCLGE_STATE_NIC_REGISTERED
to indicate that. And before calling PF NIC client's uninit_instance(),
we clear this state.

So any operation of PF NIC client from HCLGE is not allowed if this
state is not set.
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The ifdef condition of function hclge_add_fd_entry_by_arfs() is
unnecessary. It may cause compile warning when CONFIG_RFS_ACCEL
is not chosen. This patch fixes it by removing the ifdef condition.

Fixes: d93ed94f ("net: hns3: add aRFS support for PF")
Reported-by: Nkbuild test robot <lkp@intel.com>
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The FEC capbility may be changed with port speed changes. Driver
needs to read the active FEC mode, and update FEC capability
when port speed changes.

Fixes: 7e6ec914 ("net: hns3: add support for FEC encoding control")
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds aRFS support for PF. The aRFS rules are also
stored in the hardware flow director table, Use the existing
filter management functions to insert TCPv4/UDPv4/TCPv6/UDPv6
flow director filters. To avoid rule conflict, once user adds
flow director rules with ethtool, the aRFS will be disabled,
and clear exist aRFS rules. Once all user configure rules were
removed, aRFS can work again.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

In order to be compatible with aRFS rules, this patch adds
spin_lock for flow director rule adding, deleting, querying,
and packages the rule configuration.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for FEC encoding control, user can change
FEC mode by command ethtool --set-fec, and get FEC mode by command
ethtool --show-fec. The fec capability is changed follow the port
speed. If autoneg on, the user configure fec mode will be overwritten
by autoneg result.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, our driver only supports phydev to autoneg or change
port speed. This patch adds support for fibre port, driver gets
media speed capability and autoneg capability from firmware. If
the media supports multiple speeds, user can change port speed
with command "ethtool -s <devname> speed xxxx autoneg off duplex
full". If autoneg on, the user configuration may be overwritten
by the autoneg result.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Previously, we can only identify copper and fiber type, the
supported link modes of port information are always showing
SR type. This patch adds support for multiple media types,
include SR, LR CR, KR. Driver needs to query the media type
from firmware periodicly, and updates the port information.

The new port information looks like this:
Settings for eth0:
        Supported ports: [ FIBRE ]
        Supported link modes:   25000baseCR/Full
                                25000baseSR/Full
                                1000baseX/Full
                                10000baseCR/Full
                                10000baseSR/Full
                                10000baseLR/Full
        Supported pause frame use: Symmetric
        Supports auto-negotiation: No
        Supported FEC modes: None BaseR
        Advertised link modes:  Not reported
        Advertised pause frame use: No
        Advertised auto-negotiation: No
        Advertised FEC modes: Not reported
        Speed: 10000Mb/s
        Duplex: Full
        Port: FIBRE
        PHYAD: 0
        Transceiver: internal
        Auto-negotiation: off
        Current message level: 0x00000036 (54)
                               probe link ifdown ifup
        Link detected: yes

In order to be compatible with old firmware which only support
sfp speed, we remained using the same query command, and kept
the former logic.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

The test results show that the maximum time of hardware return
to mac link state is 500MS.The software needs to set twice the
maximum time of hardware return state (1000MS).

If not modified, the loopback test returns probability failure.
Signed-off-by: Nliuzhongzhu <liuzhongzhu@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

MAC tnl interruptions are different from other type of RAS and MSI-X
errors, because some bits, such as OVF/LR/RF will occur during link up
and down.

The drivers should clear status of all MAC tnl interruption bits but
shouldn't print any message that would mislead the users.

In case that link down and re-up in a short time because of some reasons,
we record when they occurred, and users can query them by debugfs.
Signed-off-by: NWeihang Li <liweihang@hisilicon.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

This patch adds support for network interface message level
settings. The message level can be changed by module parameter
or ethtool.
Signed-off-by: NYonglong Liu <liuyonglong@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>

Currently we just print few information when tx timeout happens.
In order to find out the cause of timeout, this patch prints more
information about the packet statistics, tqp registers and
napi state.
Signed-off-by: NJian Shen <shenjian15@huawei.com>
Signed-off-by: NPeng Li <lipeng321@huawei.com>
Signed-off-by: NHuazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: NDavid S. Miller <davem@davemloft.net>